Erone SEL2641R433-I - Receiver Manual

Introduction

The receiver type SEL2641 R433I is a superheterodyne single conversion receiver with integrated rolling-code decoding. The demodulation is AM/ASK. A special algorithm allows to keep synchronyzed transmitter and receiver.
The receiver which makes the activation, once received the transmitter code, has to be connected during the installation to the device to control ( gate, garage door, rolling shutters, awnings, anti-burglar appliances, lighting, etc.). The transmitter memorization can be carried out with 2 push-buttons.
All the receivers of the range Erone 433 can store into the EEPROM a serial number, a manufacturer key and a synchronism algorithm of more transmitters.
The product fully complies with the European Directives 73/23/CEE, 89/336/CEE and with the Regulation EN 60065.

Usable transmitters

Technical specifications

Main features

• Memory for 85 transmitter keys
• Display of the transmitter key number
• Display of the memory position for the last memorized transmitter
• Overwrite of a transmitter code
• Full memory cancellation.

Receiver detail

Fig. 1

Connections

Transmitter memorizing

"Red relay" output

1. Keep the button PR of the receiver pressed down until the led LR remains lit, then release the button PR.
2. Press the key of the transmitter which is to be memorized: the led LR will turn off and the relay RR will excite for a while.
3. Press the key of the transmitter again and verify the activation of the relay RR the red led LR lit and the flash of the led LV.

At each activation, and for all the transmission time, the red led LR will turn on, the green led LV will flash and the relay RR remains excited.

"Green relay" output

1. Keep the button PV of the receiver pressed down until the led LV remains lit, then release the button PV.
2. Press the key of the transmitter which is to be memorized: the led LV will turn off and the relay RV will excite for a while.
3. Press the key of the transmitter again and verify the activation of the relay RV thegreen led LV lit and the flash of the led LR.

At each activation, and for all the transmission time, the green led LV will turn on, the red led LR will flash and the relay RV remains excited.

NOTE : The memory capacity is of 85 transmitter keys. That means that a 4 keys transmitter needs 4 memory positions.

It is possible to display the memory position by following the procedure 2B A transmitter key can be memorized on each relay RR or RV but not on both.

Transmitter memory position display

1. Activate the transmitter to display and verify the which is the led that turns on and the relay which excites.
2. Keep the button PR pressed down for 1 sec.

At this point a sequence of 7 flashes of the led LR and LV commences: by taking a note of the colors it is possible to get the memory position, according to the following table
(Tab. 1):

Example:

Sequence: LR, LR, LV, LV, LR, LR, LR.
Number: 0 + 0 + 4 + 8 + 0 + 0 + 0 = 12
So the transmitter is located on the 12th memory position.

Transmitter codes overwrite

1. Keep the button PR or PV of the receiver pressed down for 4 sec. until the corresponding led remains lit, then release the button.
2. Within 2 sec. press down PV for 1 sec: the led lit will turn off.
3. Within 2 sec, begin to push PR or PV according the sequence which represents the position to overwrite ( see. tab.1 ).
4. At the end of the sequence the led LV or LR will turn on ( depending upon the memory information)
5. Within 4 sec. activate the key of the new transmitter which is to be memorized.

Memory space display

1) Keep the button PV of the receiver pressed down for 1 sec.

At this point a sequence of 7 flashes of the led LR and LV commences: by taking a note of the colors it is possible to get the number of the memory location already occupied, following the above tab.1

Memory full

When the receiver memory is full, if ( at the end of item 2 of the memorizing procedure ) the key of a new transmitter is activated, both the leds LV and LR flash 3 times.

Cancelling the entire memory

1. Keep the button PR of the receiver pressed down until the led LR remains lit.
2. Release the button PR and within 1 sec. keep the buttons PR and PV pressed down simultaneously for 4 sec. until a sequence of 3 flashes of the led LR and LV commences.
   At the end the entire memory has been cancelled.

GUARANTEE

The guarantee period of the product is 24 months, beginning from the manufacturer date. During this period, if the product does not work correctly, due to a defective component, the product will be repaired or substituted at the discretion of the producer. The guarantee does not cover the plastic container integrity. After-sale service is supplied at the producer's factory.

Manufactured by CDVI Wireless S.p. A.
Via Piave, 23 - 31020 S.Pietro di Feletto (TV) - ITALY
Tel. +39-0438-450860 - Fax. +39-0438-455628
e-mail: info@erone.com
Web: www.erone.com

Documents / Resources

References

• Erone |

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Erone SEL2641R433-I - Receiver Manual