Related Manuals for Skymsen LIS-1,5-N
Summary of Contents for Skymsen LIS-1,5-N
- Page 1 HIGH SPEED BLENDER, STAINLESS STEEL, STAINLESS STEEL CUP, 1,5 LITERS – SILENZIO MODELO LIS-1,5-N...
-
Page 2: Table Of Contents
SUMMARY 1. Introduction ..................3 1.1 Safety ........................3 1.2 Main Components ....................4 1.3 Características Técnicas ..................5 2. Installation And Pre Operation ............5 2.1 Installation ......................5 2.2 How to assemble the Blender Cup ................. 5 2.3 Pre-Operation ......................6 3. -
Page 3: Introduction
1. Introduction 1.1 Safety When using this equipment, keep in mind some basic safety precautions: 1.1.1 Read all the instructions. 1.1.2 In order to avoid the risk of electric shocks and damage to the machine, never install equipment on a wet or humid surface nor dip it in water or any other liquid. 1.1.3 The use of the equipment must be supervised when used next to children. -
Page 4: Main Components
IMPORTANT If the Power Cord is not in good usage conditions, it must be replaced by qualified personnel. 1.2 Main Components All components of this machine were designed and made to its proper function according to pattern tests and experience of Siemsen. PICTURE 01 1 –... -
Page 5: Características Técnicas
1.3 Características Técnicas TABLE 01 CHARACTERISTIC UNIT LIS-1,5-N Voltage 127 ó 220 * Frequency 50 / 60 Power Rating Consumption kW/h 0,38 Height Width Depth Net Weight Gross Weight Cup Maximum Capacity (*) Voltage will be only the one indicated on motor characteristics label. -
Page 6: Pre-Operation
PICTURE 02 2.3 Pre-Operation You have to: – Check the voltage before to switch ON the blender. Use only the voltage indicated on the blender base . – Check if the machine is firm the supporting surface must be clean and dry to avoid water or dirt to be aspired along with the air . -
Page 7: Operation
You should not: - Expect your blender to replace any other kitchen appliance. It is not supposed to make mashed potatoes, it does not blend egg white or any other cream for covering, it does not grind raw meat, it does not blend hard pastas and do not extract kernels from fruits and vegetables. -
Page 8: Cleaning
3.3 Cleaning The blenders cup parts are resistant to corrosion, hygienic and easily cleaned. Before using them for the first time and after each use, take apart the cup pieces (pic. 02) and clean them very well with warm clean water and neutral soap, wipe and dry them well. DO NOT WASH ANY PIECES IN A DISH WASHER. -
Page 9: Cautions With Stainless Steel
3.4 Cautions with Stainless Steel: The Stainless Steel may present rust signs, which ARE ALWAYS CAUSED BY EXTERNAL AGENTS, especially when the cleaning or sanitization is not constant and appropriate. The Stainless Steel resistance towards corrosion is mainly due to the presence of chrome, which in contact with oxygen allows the formation of a very thin protective coat. -
Page 10: General Safety Practices
4. General Safety Practices IMPORTANT If any recommendation is not applicable to your equipment, please ignore it. The following safety instructions are addressed to both the operator of the machine as well as the person in charge of maintenance. The machine has to be delivered only in perfect conditions of use by the Distributor to the user. -
Page 11: Safety Procedures And Notes Before Switching The Machine On
* DO NOT remove, tear off or maculate any safety or identification labels stuck on the machine. If any labels have been removed or are no longer legible, contact your nearest dealer for replacement. 4.2 Safety Procedures and Notes before Switching the Machine ON IMPORTANT Carefully read ALL INSTRUCTIONS of this manual before turning the machine ON. -
Page 12: Operation
When checking the tension of belts or chains DO NOT insert your fingers between belts and pulleys, nor between the chains and gears. Check protections and safety devices to make sure they are working properly. 4.4 Operation 4.4.1 Warnings Do not use the machine with long hair that could touch any part of the machine. This might lead to a serious accident. -
Page 13: Analysis And Problems Solving
5. Analysis and Problems Solving 5.1 Problem, causes and solutions The Blender has been designed to need minimum maintenance. However, some performance failures may happen due to normal wear during the machine lifetime. If some problem arises with your Blender, check Table - 02 as follows, where there are detailed some recommended possible solutions. - Page 14 TABLE 02 PROBLEM CAUSES SOLUTIONS - Lack of power or the plug is off - Check if the plug is on its its socket. socket, and if there is electric - The Machine does not switch power. - Problem with the internal or external electrical circuits of the - Call Technical Assistance.
-
Page 15: Electrical Diagram
6. Electrical Diagram 7. Applicable Norms Brazilian Norm No. 12 december 2010... - Page 16 METALÚRGICA SIEMSEN LTDA. CNPJ: 82.983.032/0001-19 Rodovia Ivo Silveira - km 12, nº 9525, Galpão 1 - Bairro: Bateas - CEP: 88355-202 Brusque - Santa Catarina - Brasil Fone: +55 47 3211 6000 - Fax: +55 47 3211 6020 www.siemsen.com.br - comercial@siemsen.com.br 46070.2 - INGLÊS Data de Correção: 01/09/2014 - ALÉM DESTAS MÁQUINAS, FABRICAMOS UMA LINHA COMPLETA DE EQUIPAMENTOS.
Need help?
Do you have a question about the LIS-1,5-N and is the answer not in the manual?
Questions and answers