Salda RIS 700 V EKO 3.0 Mounting And Installation Instruction
Source: salda.lt/en, vetter-lufttechnik.de
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Salda RIS 700 V EKO 3.0
Summary of Contents for Salda RIS 700 V EKO 3.0
- Page 1 RIS 700 V EKO 3.0 MOUNTING AND INSTALLATION INSTRUCTION...
-
Page 2: Table Of Contents
REGULAR SYSTEM CHECK-UP 21. ELECTRICAL CONNECTION DIAGRAM (RIS 700VE EKO 3.0) 22. ELECTRICAL CONNECTION DIAGRAM (RIS 700VW EKO 3.0) 23. ECODESIGN DATA TABLE 24. DECLARATION OF CONFIMITY 25. WARRANTY 25.1. LIMITED WARRANTY COUPON | EN RIS 700 V EKO 3.0 v2019.05... -
Page 3: Symbols And Marking
• The device should be earthed in accordance with the rules of installation of electric appliances. It is forbidden to turn on and use un- earthed device. Follow the requirements of the device’s labels that indicate Danger. RIS 700 V EKO 3.0 v2019.05 EN |... -
Page 4: Dimensions And Weight
In exceptional cases harmful gases could be drawn out of the chimney or extraction ducting back into the room. In this case we strictly recommend to turn off Salda Antifrost and use an external preheater for heat exchanger anti-frost protection (see Salda Antifrost function on the Remote controller manual). -
Page 5: Construction
+5 C +40 C +40 C +40 C -40 C -3 C +15 C Figure. 7.1. With external pre-heater operating conditions +40 C +5 C +40 C +40 C -15 C +15 C RIS 700 V EKO 3.0 v2019.05 EN |... -
Page 6: Package
+15 C Figure. 7.2. With integrated pre-heater operating conditions 8. PACKAGE QUANTITY ON THE PALLET [mm] [mm] [mm] [units] RIS 700 V EKO 3.0 1305 1120 9. TRANSPORTATION Figure. 9.1. Lifting with forklift. | EN RIS 700 V EKO 3.0 v2019.05... -
Page 7: Unpacking
The protective film is intended to protect the unit during transportation. It is recommended to remove the film because other- wise oxidation signs may occur. Before every heating season the condensate tube shall be filled with water as indicated during the first startup! Figure. 13.1. Mounting positions (W=400 mm) RIS 700 V EKO 3.0 v2019.05 EN |... -
Page 8: Floor Mounting
Draining system must be installed in the premises where the temperature is not lower than 0°C. If temperature falls below 0°C the draining system should be isolated with thermal isolation. The siphon (3) must be mounted below the AHU’s (1) level. 14. CONNECTION OF THE AIR DUCT D2 dimensions depend on unit. | EN RIS 700 V EKO 3.0 v2019.05... -
Page 9: Connection Diagram
Figure. 15.1. RIS 700 V EKO 3.0 (* KE1 - used in electrical version. In horizontal version heater is positioned before supply fan; * KV1 - used in water version. For more information please, check the manual. ** Possible to control. PE1 - self-regulating preheater) Figure. -
Page 10: Start-Up Recommendations
- Observe staff safety regulations during maintenance and repair. - The motor is of heavy duty ball bearing construction. The motor is completely sealed and requires no lubrication for the life of the motor. - Detach fan from the unit. | EN RIS 700 V EKO 3.0 v2019.05... -
Page 11: Heat Exchanger
5 minutes. For boost controlled with the fast button (FLEX control panel), boost is activated for 5 minutes if the button is pressed once, and boost will deactivated immediately if the button is pressed second time. Maximum setting is 255min. RIS 700 V EKO 3.0 v2019.05 EN |... -
Page 12: System Protection
This setting can be changed, please see Flex_meniu_montuotojas section 14 “Misc” for details. ModBus type: RTU RS485_2 port is used for connecting the ModBus (Fig. 3); Settings (see section II.6.2. of the FLEX installer description): | EN RIS 700 V EKO 3.0 v2019.05... -
Page 13: Modbus Adresses
1 - a c t i v e , Textract 01h_Read_Coils DTJ(100) temperature sensor alarm o-passive 1 - a c t i v e , Texhaust 01h_Read_Coils Exhaust air temperature sensor alarm o-passive RIS 700 V EKO 3.0 v2019.05 EN |... -
Page 14: Electrical Connection Of The Hvac Unit
Switch on the mains voltage, switch on the blade switch Q, see Fig. 5 (actual appearance of the blade switch can be different from the given photo based on the model of the product). | EN RIS 700 V EKO 3.0 v2019.05... -
Page 15: System Adjustment Guidelines
11 12 13 14 15 18 19 20 21 22 23 24 26 27 29 30 32 33 RIS 700 V EKO 3.0 v2019.05 EN | 2 3 4 5 6 7 8 9 10 26 27 29 30 32 33... -
Page 16: Control Board Rg1
LED2 Air damper close LED2 + LED3 Air damper open LED4 Water valve open LED5 Water valve close LED6 BYPASS open LED7 BYPASS close LED8 Maximal fans speed LED9 Medium fans speed | EN RIS 700 V EKO 3.0 v2019.05... -
Page 17: Labeling, Characteristics Of The Controller And The System Components
Indicates when fans fail ON/OFF ALARM 0.05mA Indicates when fans running ON/ ANTI.F 0.05mA OFF 24V Electric/Water heater controll sig- B.0.10 nal 0-10V Water heater valve actuator. A.0.10 Bypass/Rotor 0-10V +24V 24VDC 0.1A RIS 700 V EKO 3.0 v2019.05 EN |... -
Page 18: Regular System Check-Up
The blade switch should be disconnected during service (if installed on the device). If blade switch is not installed, disconnect the power supply from the distribution panel. | EN RIS 700 V EKO 3.0 v2019.05... -
Page 19: Electrical Connection Diagram (Ris 700Ve Eko 3.0)
21. ELECTRICAL CONNECTION DIAGRAM (RIS 700VE EKO 3.0) RIS 700 V EKO 3.0 v2019.05 EN |... -
Page 20: Electrical Connection Diagram (Ris 700Vw Eko 3.0)
22. ELECTRICAL CONNECTION DIAGRAM (RIS 700VW EKO 3.0) | EN RIS 700 V EKO 3.0 v2019.05... -
Page 21: Ecodesign Data Table
4396 AHS Cold [ kWh/a ] 8600 8600 8600 8600 AHS Warm [ kWh/a ] 1988 1988 1988 1988 ErP Compliance 2018 2018 2018 2018 Internet address for disassembly instructions www.salda lt RIS 700 V EKO 3.0 v2019.05 EN |... -
Page 22: Declaration Of Confimity
Should any alterations be made in the products, this declaration will no longer apply. Notified body: VšĮ Technikos priežiūros tarnyba, Naugarduko g. 41, LT – 03227 Vilnius, Lithuania, identification number 1399. Quality: Salda UAB activities are in line with the international quality management system standard ISO 9001:2015. Date... -
Page 23: Warranty
3.4. when the unit was used not for its original purpose. 3.5. Company SALDA UAB is not responsible for potential loss of property or personal injury in cases where AHU is manufactured without a control system and the control system will be installed by the client or third parties. The manufacturer’s warranty does not cover devices that will be damaged by installing the control system. - Page 24 Heat exchanger cleaning Every 3-4 Filter replacement months** Look at the product label. ** - At least. NOTE. The purchaser is required to fill in the “Product maintenance table”. MAN000028 MAN000028 Ragainės g. 100 +370 41 540 415 Šiauliai LT-78109, LITHUANIA office@salda.lt...
Need help?
Do you have a question about the RIS 700 V EKO 3.0 and is the answer not in the manual?
Questions and answers