Related Manuals for Videofied XT 620
Summary of Contents for Videofied XT 620
- Page 1 XT 210/620/730 GPRS Control Panel I N S T A L L M A N U A L Doc. - Ref. 230-XT Last modification date : June 2014 Firmware version : XLP.04.04.05.XXX and later www.videofied.com...
-
Page 2: Introduction
The XT is a fully wireless alarm system. It can be powered by standalone batteries or connected to a power supply. This panel is intended mainly for residential and commercial markets. With the Motion Viewers™ and Videofied ® range of products, the XT panel provides video verification in case of intrusion. -
Page 3: Table Of Contents
4.5 Delete the keypad or any other device..................19 4.6 Read the event log........................20 4.7 Programmable inputs and outputs...................20 4.8 Golden rules..........................21 5. Transmitted events list ..................... 6. 2G3G error codes....23 ..................7. Technical specification and security notes ............www.videofied.com... -
Page 4: Xt Panel Setup
DO NOT insert or remove the SIM card while the panel is powered. 1.2 Panel mounting Fix the back casing on the wall using the three mounting holes as shown. Mounting the panel is not required for programming. Bracket holes www.videofied.com... -
Page 5: Powering And Initialization
The panel is now reset, a CMA, XMA or XMB has to be enrolled to configure the panel. THE CONTROL PANEL MUST BE CONNECTED TO AN EXTERNAL POWER SUPPLY (OPTION 1) WHEN USING THE RINGTONE FEATURE OR SMARTPHONE APP. Option 1 Programming button Mains power supply Option 2 www.videofied.com... -
Page 6: Pairing The Keypad
Insert all LS14500 Lithium batteries into the keypad. • Do not mount the keypad. It will display one of the following screens: RSI (c) 2013 <=========XX=========> videofied.com • Press on both ESC NO keys at the same time and release. The indicator LED on the keypad will blink rapidly. -
Page 7: Xtender Mode
On a programed panel, you can choose between standalone and XTENDER modes from the menu : *When using an XT in XTENDER CONFIGURATION (LVL 4) > GENERAL PARAMETERS > XTENDER mode, the panel has to be powered by the mains power supply. www.videofied.com... -
Page 8: Xt Panel Programming
OK or YES There is no back door or Default codes to the system. Please refer to the restriction rule for codes (Chapter 4.4). CONFIRM CODE Some codes are already used by default and therefore cannot be used. OK or YES www.videofied.com... - Page 9 13/10/14 10:47 ENTRY COMPLETE ! CONNECTED TO MONITOR. STATION? OK or YES Use the Alphanumeric Keypad to enter in a 4-8 digit ACCOUNT NUMBER : account number provided by the Central Station. ACCOUNT NUMBER : 567001 OK or YES www.videofied.com...
- Page 10 Events list NOT TRANSMITTED: event is not transmitted, however it will appear on the keypad. Please liaise with your Monitoring Station to ensure that the requested events to transmit are correctly set. SERVER ADDRESSES ? OK or YES www.videofied.com...
- Page 11 It makes a difference between UPPER and lower case letters. To switch between UPPER and lower case, use the M/m key from CMA keypad or hold a digit key (0-9) for XMA/XMB. 2G3G PARAMETERS ? 2G3G LEVEL ? www.videofied.com...
- Page 12 The 2G3G level test can last several minutes. Do not interrupt the test or remove the SIM card during the test. OK or YES IMPORTANT : Videofied will require a 3/5 grade or better for reliable transmission of Video alarms. 2G3G LEVEL ?
-
Page 13: Xtender Mode Configuration
Enter the value you would like for the Arming Confirmation (0) : _ and press OK or YES For further information about the programmable inputs and outputs, please consult the following application notes available on our support website: 240-XT - APP NOTE - XTENDER CONFIGURATION MODE www.videofied.com... - Page 14 OK or YES LED indicator shall be turned off. After initial programming has been completed, make SYSTEM CHECK use of the menu overview document (available on our IN PROGRESS technical support website), to see full programming options. INSTALLATION SUCCESSFUL ! www.videofied.com...
-
Page 15: Xt Features Guide
OK or YES and press and press ( XMB model only) OK or YES OK or YES With remote Present your badge on badge reader the badge reader BR250 With remote Press Press keyfob www.videofied.com... -
Page 16: Arming And Siren Mode Configuration
CONFIGURATION (LVL 4) > AREAS AND DEVICES > DEVICES > DEVICES CONFIGURATION > DEVICE TYPE When in the ‘Arm From Host’ mode, the Videofied system will only arm and disarm when 9-12v is supplied and sustained. When both arming inputs are supplied voltage at the same time the Videofied Keypad display will show ‘SYSTEM ARMED. -
Page 17: Manage Badges And Access Codes
After 1 min of no use of the keypad and no tests running, the display returns to the standby display and LVL1. • When standby display, if the ESC NO key is held during 5s, the level is changed to LVL1. www.videofied.com... - Page 18 All user codes +2 The -1 and -2 codes (0998 et 0999) are as panic/duress codes. reserved to prevent conflicts when creating a All user codes -1 A total of 186 codes are forbidden. new user code. All user codes -2 www.videofied.com...
-
Page 19: Delete The Keypad Or Any Other Device
OK or YES A1 : KEYPAD KEYPAD 1 OK or YES DELETE OK or YES < = = = = XX = = = = > You can now remove the batteries from the device www.videofied.com... -
Page 20: Read The Event Log
The XT control panel has 3 programmable inputs and 2 programmable outputs. Please note that we advise to connect the panels to a power supply when using programmable inputs. These functions allow the linking of Videofied ® security systems to auxiliary equipment such as panic buttons, pepper spray, smoke generator, hard-wired door contact, light curtain, etc. -
Page 21: Golden Rules
LCD screen goes dark after 30 seconds of inactivity, press an Registration of up to 25 devices (including the keypad). arrow or numeric key to light it up. Use only batteries provided by Videofied (siren : Alkaline Respect indoor infrared devices installation height (2m10 to 2m30). batteries). -
Page 22: Transmitted Events List
After initial programming, using a remote keypad : Use the arrows to access : CONFIGURATION (level 4) > CONFIGURATION MONITOR. STATION > MONITORING PARAMETERS > EVENT TRANS. MODIFICATION Then use the arrows to determine the event to modify. Press OK or YES to edit. www.videofied.com... -
Page 23: G3G Error Codes
Insufficient GPRS Network: When the panel is unable to find any signal, proceed to GPRS level test in another location on site. You can also find the network state or condition of use by directly contacting your local operator. www.videofied.com... -
Page 24: Technical Specification And Security Notes
NF C 48-212:2004 NF EN50130-4:1995; A1:1998; A2:2003 NF EN50130-5: 1998 Class II EMEA SALES North American Headquarters 1375 Willow Lake Blvd, Suite 103 23, avenue du Général Leclerc Vadnais Heights, MN 55110 92340 BOURG-LA-REINE FRANCE E-Mail : usasales@rsivideotech.com E-Mail : emeasales@rsivideotech.com www.videofied.com...