Advertisement
Quick Links
Advertisement
Related Manuals for Ferroli BLUEHELIX B S 45
Summary of Contents for Ferroli BLUEHELIX B S 45
- Page 1 BLUEHELIX B S 45 IT ISTRUZIONE PER L’USO L'INSTALLAZIONE E LA MANUTENZIONE ES INSTRUCCIONES DE USO, INSTALACIÓN Y MANTENIMIENTO TR KULLANMA, KURULUM VE BAK M TALIMATLAR EN INSTRUCTIONS FOR USE, INSTALLATION AND MAINTENANCE FR INSTRUCTIONS D'UTILISATION, D'INSTALLATION ET D'ENTRETIEN...
-
Page 2: General Warnings
BLUEHELIX B S 45 Indication during operation 1. GENERAL WARNINGS Heating “d2” fig. 2 Domestic hot water (DHW) “d1“ 2. OPERATING INSTRUCTIONS 2.1 Introduction BLUEHELIX B premix condensing fig. 3 heat exchanger in steel Fault partially pro- tected place "d3"... - Page 3 BLUEHELIX B S 45 Boiler electrically powered 2.4 Adjustments Switch on the power to the boiler. Summer/Winter Switchover summer/winter summer/winter Heating temperature adjustment fig. 5 - Switching on / Software version fig. 9 DHW temperature adjustment fig. 6 - Venting cycle...
-
Page 4: Installation
BLUEHELIX B S 45 Press the heating buttons (detail 3 - fig. 1) to access parallel curve offset; the display 3. INSTALLATION shows "OF" flashing. Use the DHW buttons (detail 1 - fig. 1) to adjust the parallel curve 3.1 General Instructions offset according to the characteristic (fig. - Page 5 BLUEHELIX B S 45 Connection to a storage tank for domestic hot water production Accessing the electrical terminal block The unit's electronic board is arranged for managing an external storage tank for domes- The electrical terminal block (fig. 15) can be accessed after removing the front panel (*** tic hot water production.
- Page 6 BLUEHELIX B S 45 Connection with separate pipes Table. 6 - Accessories Losses in m Fume exhaust inlet Vertical Horizontal PIPE 1 m M/F 1KWMA83W BEND 45° M/F 1KWMA65W 90° M/F 1KWMA01W PIPE SECTION with test point 1KWMA70W Ø 80...
- Page 7 BLUEHELIX B S 45 Configuration of flues Air inlet = / Fume outlet = Table. 7 - Connection with coaxial pipes Left outlets 041001X0 Rear outlets 041001X0 Right outlets 041001X0 1KWMA64W...
- Page 8 BLUEHELIX B S 45 Table. 8 - Connection with separate pipes Left outlets Rear outlets Right outlets...
-
Page 9: Service And Maintenance
BLUEHELIX B S 45 Connection to collective flues Replace nozzle B inserted in the gas pipe with that contained in the conversion kit, interposing seal D (see fig. 23). Reassemble the valve and check the tightness of the connection. Apply the label, contained in the conversion kit, near the data plate. - Page 10 BLUEHELIX B S 45 TEST mode activation 4.3 Maintenance Press the heating buttons (details 3 and 4 - fig. 1) together for 5 seconds to activate the Opening the front panel TEST mode. The boiler lights at the maximum heating power set as described in the fol- To open the boiler casing pull the panel outwards and release it (see fig.
-
Page 11: Technical Data And Characteristics
BLUEHELIX B S 45 4.4 Troubleshooting Fault Fault Possible cause Cure code Diagnostics No system H O circulation Check the circulating pump In case of operation faults or problems, the display flashes and the fault identification Exchanger protection activa- code appears. - Page 12 BLUEHELIX B S 45 fig. 29 - Top view (AIR INLET = / FUME OUTLET = 5.2 Water circuit fig. 27 - Side view 50 50 fig. 30 - Water circuit fig. 28 - Rear view...
- Page 13 BLUEHELIX B S 45 5.3 Diagrams 5.4 Technical data table Circulating pump head / pressure losses The column on the right gives the abbreviation used on the data plate. H [m H 1.000 1.500 2.000 2.500 Q [l/h] fig. 31 - Circulating pump head / Pressure losses BLUEHELIX B A = Boiler pressure losses - B = Circulating pump min.
- Page 14 BLUEHELIX B S 45...
- Page 15 BLUEHELIX B S 45 5.5 Wiring diagram LC32 FUSE 3.15A 250V 10 k 1.8 k 1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 1 2 3 4 5 6 7 8 9...