Page 1
OR MAINTENANCE OF THIS EQUIPMENT CAN RESULT OR MAINTENANCE OF THIS EQUIPMENT CAN RESULT IN SERIOUS INJURY OR DEATH. IN SERIOUS INJURY OR DEATH. 2208 Starting w/Serial #322AR08001 2208 Starting w/Serial #322AR08001 2210 Starting w/Serial #322AR10001 2210 Starting w/Serial #322AR10001...
H&S WARRANTY H&S Manufacturing Co., Inc. (“H&S”) warrants this product to be free from defect in material and workmanship. Except as noted below, this warranty term is twelve (12) months on parts and labor, and twenty-four (24) months on parts only from the date of delivery of the product to the original purchaser by an authorized H&S dealer.
H&S reserves the right to make changes or add improvements to its products at any time without incurring any obligation to make such changes to products previously manufactured. Specifications, statements and descriptions of Products contained in this publication are subject to change without prior notification.
DEALER PRE-DELIVERY CHECKLIST AFTER COMPLETION, DEALER SHOULD REMOVE AND RETAIN FOR RECORDS After the Rake has been completely set up, check to be certain it is in correct operating order before delivering to the customer. The following is a list of points to inspect. Check off each item as you have made the proper adjustments and found the item operating satisfactorily.
DEALER DELIVERY CHECKLIST AFTER COMPLETION, DEALER SHOULD REMOVE AND RETAIN FOR RECORDS This checklist that follows is an important reminder of valuable information that should be passed on to the customer at the time this rake is delivered. Check off each item as you explain it to the customer. This delivery checklist, when properly filled out and signed, assures the customer that the pre-delivery service was satisfactorily performed.
SAFETY INFORMATION YOUR SAFETY ALERT! IS INVOLVED. THIS SYMBOL IS USED THROUGHOUT THIS BOOK WHENEVER YOUR PERSONAL SAFETY IS INVOLVED. TAKE TIME TO BE CAREFUL. REMEMBER: THE CAREFUL OPERATOR IS THE BEST OPERATOR. MOST ACCIDENTS ARE CAUSED BY HUMAN ERROR. CERTAIN PRECAUTIONS MUST BE OBSERVED TO PREVENT THE POSSIBILITY OF INJURY OR DAMAGE.
SAFETY INFORMATION Keep signs in good condition. Immediately replace any missing or damaged signs. RECOGNIZE SAFETY INFORMATION This is the safety alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury.
TRACTOR: This operator’s manual uses the term “Tractor” when identifying the power source. W A R N I N G TO PREVENT SERIOUS INJURY OR DEATH BEFORE YOU ATTEMPT TO OPERATE THIS EQUIPMENT, READ AND STUDY THE FOLLOWING INFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO OPERATES OR WORKS WITH THIS EQUIPMENT, WHETHER FAMILY MEMBER OR EMPLOYEE, IS FAMILIAR WITH THESE SAFETY PRECAUTIONS.
CAP SCREW TORQUE VALUES The specifications below are the torque values for fasteners as it adheres to the SAE torque value standards. All fasteners should be torqued to the proper values found in the figures below unless otherwise specified by the engineering drawing. •...
SET-UP & ASSEMBLY NOTE: Determine right or left side of the Rake by viewing it from the rear. If instructions or parts lists call for hardened bolts, refer to the Cap Screw Torque Values page to identify. 1. Assemble the Rake or check the Rake for proper assembly and adjustment. Make sure that all bolts are tightened.
TRANSPORTING TOWING ON HIGHWAY Follow state and local regulations when towing farm equipment on public highways. Never tow the rake on a public highway at a speed greater than 20 mph (32 kph). REFLECTORS Reflective decals are on the outer edges and sides of the rake for safety. Front facing amber Side facing amber Rear red reflective...
PREPARING FOR OPERATION ADJUSTMENTS There are multiple settings available for adjusting the hitch as shown in the picture. 1. Adjust the tractor hitch (if possible) so that it is 13 to 17 inches above ground. 2. Attach the rake to tractor with a 1” hitch pin that has a safety locking device.
OPERATION & ADJUSTMENTS EMERGENCY SHUTDOWN Stop the tractor engine, remove ignition key, and allow all mechanisms to stop before cleaning or working on the machine. IMPORTANT: Retighten all bolts on the rake after 100 acres as bolts can loosen up on new machinery. Re-torque rake tooth bolts after first 100 acres.
Page 20
OPERATION & ADJUSTMENTS FLOATATION Rake Arm/Wheels Floatation pressure of the rake wheels can be adjusted by adjusting the pressure rod assembly. • Hydraulically raise the rake beams so they are off the ground approximately 6”. • Loosen the lock ring and turn the rod collar to show more threads. This increases the down pressure of the rake wheels.
OPTIONAL EQUIPMENT CENTER KICKER WHEEL An optional center kicker wheel is available. If the hay is laying out flat, the extra wheel allows you to move the hay lying in the center of the rake out of the stubble for easier pick-up.
Page 22
LUBRICATION Become familiar with all lubrication points and establish a routine to ensure complete lubrication of the rake. GENERAL INFORMATION IMPORTANT: Catch and dispose of fluid per local waste disposal regulations whenever service is performed on hydraulic components, valves, cylinders, hoses, etc. WHEEL BEARING LUBRICATION, CLEAN &...
LUBRICATION 2 zerks on the front 2 zerks on the front of LH lift arm of RH lift arm 10 & 12-wheel only 10 & 12-wheel only 2 zerks on the rear 1 zerk on 2 zerks on the front of RH lift arm each beam of LH lift arm...
Stay Clear of Rake 11599 Do Not Go Near leaks 54033 U.S.A. 71188B Jack Storage Position 72203A Help Avoid Injury - Read and understand the operator’s manual 94222 2208 Decal/Right 94225 2210 Decal/Right 94226 2212 Decal/Right 90597 2208 Decal/Left 90596 2210 Decal/Left 90594...
TROUBLESHOOTING NOTE: This Troubleshooting Chapter presents problems, causes and suggested remedies beyond the extent of loose, worn or missing parts. It was developed with the understanding that the machine is in otherwise good operating condition. WARNING: MAKE SURE THAT THE TRACTOR IS SHUT OFF AND THE RAKE CANNOT MOVE BEFORE SERVICING THE RAKE.
Page 32
H&S MFG. CO. products approved for the FEMA SEAL OF QUALITY Manufactured By: H&S MANUFACTURING CO., INC. 2608 S. HUME AVE. MARSHFIELD, WI 54449 (715) 387-3414 | hsmfgco.com...