Table of Contents
Advertisement
Quick Links
D0T Series PIR Siren Camera
User Manual
Thank you for purchasing our product. If there are any
questions, or requests, do not hesitate to contact the
dealer.
This manual applies to the models below:
Type I Camera
Type II Camera
This manual may contain several technical mistakes or
printing errors, and the content is subject to change
without notice. The updates will be added to the new
version of this manual. We will readily improve or
update the products or procedures described in the
manual.
Type
User Manual
Model
DS-2CE12D0T-PIRXF
DS-2CE72D0T-PIRXF
01000020201211
Advertisement
Table of Contents
Related Manuals for HIKVISION DS-2CE12D0T-PIRXF
Summary of Contents for HIKVISION DS-2CE12D0T-PIRXF
- Page 1 This manual applies to the models below: Type Model Type I Camera DS-2CE12D0T-PIRXF Type II Camera DS-2CE72D0T-PIRXF This manual may contain several technical mistakes or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual.
-
Page 2: Regulatory Information
Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. - Page 3 Safety Instruction Warnings In the use of the device, you must be in strict compliance with the electrical safety regulations of the nation and region. Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 12 VDC according to the IEC60950-1 standard and IEC62368-1 standard.
-
Page 4: Product Features
1 Introduction 1.1 Product Features The main features are as follows: High performance CMOS sensor OSD menu with configurable parameters Smart IR PIR detection Built-in siren 4 in 1 video output 1.2 Overview 1.2.1 Overview of Type I Camera Switch Button Video Cable Bracket... -
Page 5: Installation
2 Installation Before you start Make sure that the device in the package is in good condition and all the assembly parts are included. Make sure that all the related equipment is power-off during the installation. Check the specification of the products for the ... - Page 6 Note: The supplied screw package contains self-tapping screws, and expansion bolts. For cement wall/ceiling, expansion bolts are required to fix the camera. For wooden wall/ceiling, self-tapping screws are required. 5. Connect the corresponding power cord, and video cable. 6.
- Page 7 5. Secure the junction box’s body on the ceiling/wall with supplied screws. Figure 2-6 Secure the Junction Box on the Wall/Ceiling 6. Route the cables through the bottom cable hole, or the side cable hole of the junction box. 7. Combine the junction box cover with its body. Figure 2-7 Combine the Junction Box Cover back to its Body 8.
-
Page 8: Ceiling/Wall Mounting With Junction Box
Figure 2-9 Pry the Mounting Base 3. Drill screw holes and the cable hole on the ceiling. 4. Attach the mounting base to the ceiling and secure it with supplied screws. For cement ceiling, you need to install the expansion bolts at first. Expansion Bolts Self-tapping Screws Figure 2-10 Attach the Mounting Base to the Ceiling... - Page 9 1. Drill screw holes and the cable hole (optional) on the wall. 2. Take apart the junction box, and align the screw holes of the mounting base with those on the junction box’s cover. 3. Install the mounting base to the junction box’s cover with three PM4 screws.
-
Page 10: Menu Description
3 Menu Description Please follow the steps below to call the menu. NOTE: The actual display may vary with your camera model. Steps: 1. Connect the camera with the TVI DVR, and the monitor, shown as the figure 3-1. Figure 3-1 Connection 2. -
Page 11: Video Format
2). Click Iris + to confirm the selection. 3). Click left/right direction button to adjust the value of the selected item. 3.1 VIDEO FORMAT You can set the video format to 2MP@30fps or 2MP@25fps. 3.2 EXPOSURE EXPOSURE MODE You can set the EXPOSURE MODE to GLOBAL, BLC, HLC, or DWDR. -
Page 12: Video Settings
The Smart IR function is used to adjust the light to its most suitable intensity, and prevent the image from over exposure. AUTO Automatically switch Color, or B&W (Black and White) according to actual scene brightness. You can turn on/off the IR LIGHT, and set the value of SMART IR in this menu. - Page 13 WHITE BALANCE White balance, the white rendition function of the camera, is to adjust the color temperature according to the environment. It can remove unrealistic color casts in the image. You can set WHITE BALANCE mode to AUTO, or MANUAL. AUTO ...
-
Page 14: Alarm Time
This function is only showed when you switch the video output to TVI mode. 3.5.3 ALARM TIME ALARM TIME refers to the duration of audible and visual alarm. 3.5.4 VOLUME You can set the volume to HIGH, MEDIUM, or LOW. 3.6 FACTORY DEFAULT Reset all the settings to the factory default.