HIKVISION DS-2CE10HFT-F User Manual

HIKVISION DS-2CE10HFT-F User Manual

Colorvu 5 mp turbohd bullet and turret cameras
Hide thumbs Also See for DS-2CE10HFT-F:

Advertisement

olorVu
5 MP
Bullet and Turret
Cameras
User Manual
122919NA
DS-2CE10HFT-F • DS-2CE10HFT-F28
DS-2CE12HFT-F • DS-2CE12HFT-F28
DS-2CE72HFT-F • DS-2CE72HFT-F28

Advertisement

Table of Contents
loading

Summary of Contents for HIKVISION DS-2CE10HFT-F

  • Page 1 5 MP Bullet and Turret Cameras User Manual 122919NA DS-2CE10HFT-F • DS-2CE10HFT-F28 DS-2CE12HFT-F • DS-2CE12HFT-F28 DS-2CE72HFT-F • DS-2CE72HFT-F28...
  • Page 2: Table Of Contents

    Contents User Manual ............3 Regulatory Information ............. 3 FCC Information ............3 FCC Compliance ............3 FCC Conditions ............3 EU Conformity Statement ..........3 Industry Canada ICES-003 Compliance ......4 Warning ............4 Safety Instruction ............4 Warnings ............
  • Page 3: User Manual

    User Manual Thank you for purchasing our product. If there are any questions or requests, please contact your dealer. This manual applies to the models below: Type Model DS-2CE10HFT-F Type I Camera DS-2CE10HFT-F28 DS-2CE12HFT-F Type II Camera DS-2CE12HFT-F28 DS-2CE72HFT-F Type III Camera...
  • Page 4: Industry Canada Ices-003 Compliance

    Voltage Directive 2014/35/EU, the EMC Directive the RoHS Directive 2011/65/EU 2014/30/EU, 2012/19/EU (WEEE Directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points.
  • Page 5: Cautions

    Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 12 VDC according to the IEC60950-1 standard. Refer to technical specifications for detailed information. Do not connect multiple devices to one power adapter to avoid overheating or a fire hazard caused by overload.
  • Page 6: Introduction

    1 Introduction 1.1 Product Features The main features are as follows: High performance CMOS sensor • OSD menu with configurable parameters • 24-hour color image • Smart light • 3-axis adjustment • 1.2 Overview 1.2.1 Overview of Type I Camera Figure 1, Type 1 Camera Overview Press and hold the switch button for five NOTE:...
  • Page 7: Installation

    2 Installation Before You Start Make sure that the device in the package is in good • condition and all assembly parts are included. Make sure that all related equipment is powered off • during the installation. Check the products’ specifications for the installation •...
  • Page 8: Ceiling/Wall Mounting With Junction Box

    Figure 5, Secure the Camera to the Ceiling Attach the bracket to the ceiling, and secure the camera with supplied screws. The supplied screw package contains self- NOTES: tapping screws and expansion bolts. For a concrete wall/ceiling, expansion bolts are required to fix the camera.
  • Page 9: Installation Of Type Ii Camera

    Take apart the junction box, and align the camera screw holes with those on the junction box cover. Attach the camera to the junction box cover with supplied screws. Figure 8, Attach Camera to Junction Box Cover Secure the junction box body on the ceiling/wall with supplied screws.
  • Page 10 Drill the screw holes and the cable hole (optional) on the ceiling according to the drill template. Figure 11, Drill Template NOTE: Drill a cable hole when using the ceiling outlet to route the cable. Route the cables through the cable hole or the side opening.
  • Page 11: Installation Of Type Iii Camera

    2.3 Installation of Type III Camera 2.3.1 Ceiling/Wall Mounting without Junction Box Before You Start Ceiling mounting and wall mounting are similar. The following uses ceiling mounting as an example. Disassemble the camera by rotating it to align the notch to one of the lines, as shown below. Figure 14, Dissemble the Camera Pry the mounting base open with a flat object (for example, a coin).
  • Page 12: Ceiling/Wall Mounting With Junction Box

    The supplied screw package contains self- NOTE: tapping screws and expansion bolts. Route the cables through the cable hole or side opening. Re-install and secure camera to the mounting base. Figure 18, Install the Camera Back Connect the corresponding cables such as power cord and video cable.
  • Page 13 Figure 20, Drill Template NOTE: Drill a cable hole when using a ceiling outlet to route the cable. Take apart the junction box, and align the mounting base screw holes with those on the junction box cover. Install the mounting base to the junction box cover with three PM4 screws.
  • Page 14: Menu Description

    Figure 23, Finish the Installation 3 Menu Description Follow the steps below to call the menu. NOTE: The actual display may vary by camera model. Connect the camera to the TVI DVR and the monitor, as shown below. Figure 24, Connection Power on the camera, TVI DVR, and the monitor to view the image on the monitor.
  • Page 15 Figure 25, Main Menu Overview Click the direction arrow to control the camera. 1) Click up/down button to select the item. 2) Click Iris + to confirm the selection. 3) Click left/right button to adjust selected value. UM ColorVu DS-2CExxHFT-Fxx 122919NA...
  • Page 16: Video Format

    3.1 VIDEO FORMAT You can set the video format to 5 MP @ 20 fps, 4 MP @ 30 fps, 4 MP @ 25 fps, 2 MP @ 30 fps, or 2 MP @ 25 fps. 3.2 EXPOSURE 3.2.1 EXPOSURE MODE You can set the EXPOSURE MODE to GLOBAL, BLC, HLC, WDR, or HLS.
  • Page 17: Video Settings

    3.3 VIDEO SETTINGS Move the cursor to VIDEO SETTINGS and click Iris+ to enter the submenu. IMAGE MODE, WHITE BALANCE, BRIGHTNESS, CONTRAST, SHARPNESS, SATURATION, 3DNR, and MIRROR are adjustable. Figure 26, Video Settings 3.3.1 IMAGE MODE IMAGE MODE adjusts the image saturation. You can set it to STD (Standard) or HIGH-SAT (High Saturation).
  • Page 18: Saturation

    3.3.6 SATURATION Saturation is the proportion of pure chromatic color in the total color sensation. Adjust this feature to change the color intensity. 3.3.7 3 DNR (3D DNR) 3 DNR refers to 3D digital noise reduction. Compared to general 2D digital noise reduction, 3D digital noise reduction processes the noise between two frames in addition to processing the noise in one frame.
  • Page 19: Exit

    3.7 EXIT Move the cursor to EXIT and click Iris+ to exit the menu. 3.8 SAVE & EXIT Move the cursor to SAVE & EXIT and click Iris+ to save the settings and exit the menu. UM ColorVu DS-2CExxHFT-Fxx 122919NA...

Table of Contents