Anest Iwata KIWAMI-1-18B14 Instruction Manual

INSTRUCTION MANUAL
Spray Gun
Be sure to observe warning s and cautions in this instruction manual.
If not, it can cause paint ejection and serious bodily injury by drawing organic solvent.
Be sure to observe following marked items which are especially important .
Indicates a potentially hazardous situation which, if not avoided, may result in serious injury or loss of life.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury or
property damage.
Indicates notes which we ask you to observe. The safety precautions in this instruction manual are the
minimum necessary conditions. Follow national and local regulations regarding fire prevention, electricity
and safety as well as your own company regulations.
IMPORTANT WARNING: Our spray guns, airbrushes, and other products are made to conform by our local group companies with local laws and regulations
that may differ from place to place. Improper trade of products outside of designated domestic territories (unauthorized reselling) can result in legal violations,
local fines, and penalties. ANEST IWATA CORPORATION assumes no liability for products acquired through unauthorized reselling and in such cases and due
to quality control protocols, unauthorized reselling renders the warranty null and void.
Symbol Marking on the Spray Gun:
This Anest-iwata spray gun kit
complies to machinery directive
2006/42/EC and ATEX directive
2014/32/EU,for EU market and
machinery regulations 2008
No.1597 ATEX directive 2016
No.1107 for UK market.
Important specifications
Max. Pressure 0.70MPa / 7.0bar / 100psi
Noise level 79dB(A)
Spray condition Recommended
Measuring point 1m backwards from spray gun, 1.6m height
Max. temperature Atmosphere: 5°C ~40°C (41°F~104°F)
Important
Never connect pressure feeding paint except pressure feed type spray gun.
Main specifications
Nozzle orifice
Type of
Model
feed
KIWAMI-1-13B4
-14B2
-16B2
-13KP6
-14KP6
Gravity
-13B8
-14B8
-13B10
-16B12
-18B14
Suction
-14B8S
Pressure
※ 1. Atomizing air pressure means air pressure at gun inlet when trigger is pulled and air flows ．
※ 2. Opening of fluid adjust knob is 3 turns from full close.
II 2 G Ex h X
II
Complies Specific Group II
with Marking for (Surface)
European Explosion
Directive Protective
Air and Fluid: 5°C ~43°C (41°F~109°F)
Recommended condition
Air cap assy
Φ mm (in)
Mark Atomizing air pressure
MPa (bar / PSI)
1.3 (0.051) B4 0.20(2.0/29)
1.4 (0.055)
B2 0.24(2.5/36)
1.6 (0.062)
1.3 (0.051)
KP6 0.20 (2.0/29)
1.4 (0.055)
1.3 (0.051)
B8 0.20 (2.0/29)
1.4 (0.055)
1.3 (0.051) B10 0.15 (1.5/21.8)
1.6 (0.062) B12 0.18 (1.8/26.1)
1.8 (0.069) B14 0.15 (1.5/21.8)
1.4 (0.055) B8 0.20 (2.0/29)
2 G Ex h
Category Type of Ignition
(Zone 1&2) Atmosphere Protection
(GAS) (not applied)
Model
KIWAMI-1-13B4
KIWAMI-1-14B2
KIWAMI-1-16B2
KIWAMI-1-13KP6
KIWAMI-1-14KP6
KIWAMI-1-13B8
KIWAMI-1-14B8
KIWAMI-1-13B10
KIWAMI-1-16B12
KIWAMI-1-18B14
KIWAMI-1-14B8S
Air
Fluid output consumption
※ 1
mL/min L/min (cfm)
140 160 (5.6)
200
230 (8.1)
195
165
200 (7.1)
170
185
230 (8.1)
200
140 200 (7.1)
155 220 (7.8)
※ 2
175 180 (6.4)
※ 2
160
230 (8.1)
180
− 1 −
This manual contains IMPORTANT
WARNINGS and INSTRUCTIONS.
Equipment in this manual is exclusively for
painting purposes.
Do not use for other purposes.
The operator shall be fully conversant with
the requirements stated in this instruction
manual including important warnings,
cautions and operation and correct handling.
Read and understand the instruction
manual, before use and retain for reference.
IIB T6 Gb
Explosion Temperature Explosion
Group Class Protection
(Ethylene) (≤ 85°C) level
(EPL)
Nozzle needle assy combination
Fluid nozzle
Orifice Φ mm (in) Mark
Φ 1.3 (0.051) / K1 / 13B4
Φ 1.4 (0.055) / K1 / 14B2
Φ 1.6 (0.062) / K1 / 16B2
Φ 1.3 (0.051) / K1 / 13KP6
Φ 1.4 (0.055) / K1 / 14KP6
Φ 1.3 (0.051) / K1 / 13B8
Φ 1.4 (0.055) / K1 / 14B8
Φ 1.3 (0.051) / K1 / 13B10
Φ 1.6 (0.062) / K1 / 16B12
Φ 1.8 (0.069) / K1 / 18B14
Φ 1.4 (0.055) / K1 / 14B8
Spray
Pattern width
distance Viscosity
mm (in)
mm (in) s/Ford#4
250 (9.8)
275 (10.8)
200 (7.9)
240 (9.4) 200 (7.9)
245 (9.6)
260 (10.2)
275 (10.8)
240 (9.4) 150 (5.9)
275 (10.8) 200 (7.9)
※ 2
235 (9.2) 150 (5.9)
※ 2
240 (9.4)
200 (7.9)
250 (9.8)
T
Amb
X
+5°C +40°C
Additional
Ambient
conditions: Any
Temperature
static Electricity
should be
discharged and
needs to be
diverted to the
ground via a
conductive air hose
not included.
Fluid needle
Mark
13 WIDER1
13H WIDER1
13 WIDER1
18 WIDER1
13 WIDER1
Paint
Mass
Air & fluid
g (lbs.)
connection
16
22
Air
G1/4
(NPS1/4)
16
290
(0.64)
Fluid
G1/4
18
(NPS1/4)
18
16
22