ESAB Origo Mig C151 Instruction Manual
Hide thumbs Also See for Origo Mig C151:

Advertisement

GB
Origo™
Mig C141/ C151
Mag C171/ C201/ C251
Instruction manual
0463 326 001 GB 20120528
Valid for serial no. 736-xxx-xxxx

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Origo Mig C151 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for ESAB Origo Mig C151

  • Page 1 Origo™ Mig C141/ C151 Mag C171/ C201/ C251 Instruction manual 0463 326 001 GB 20120528 Valid for serial no. 736-xxx-xxxx...
  • Page 2 - 2 -...
  • Page 3: Table Of Contents

    1 SAFETY ............2 INTRODUCTION .
  • Page 4: Safety

    SAFETY Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or near the equipment observes all the relevant safety precautions. Safety precautions must meet the requirements that apply to this type of equipment. The following recommendations should be ob­...
  • Page 5 As the person responsible for the equipment, it is your responsibility to obtain information on approved collection stations. For further information contact the nearest ESAB dealer. ESAB can provide you with all necessary welding protection and accessories. - 5 - ba47e...
  • Page 6: Introduction

    + and - connections on the switching terminal by the wire feed unit. ESAB's accessories for the product can be found on page 26. Equipment The power source is supplied with:...
  • Page 7 Mig C141 Mig C151 Mag C171 -10 ÷ +40 -10 ÷ +40 -10 ÷ +40 Operating temperature Enclosure class IP 23 IP 23 IP 23 Application classifica­ tion Mag C201 Mag C251 Voltage 220-230V, 1∼ 50/60Hz 220-230V, 1∼ 50/60Hz Permissible load at 100% duty cycle 90A/18.5V 110A/19.5V...
  • Page 8: Installation

    Application class The symbol indicates that the power source is designed for use in areas with increased electrical hazard. INSTALLATION The installation must be carried out by a professional. Note! Connect the power source to the electricity mains with a network impedance of (C141 - 0.41; C151 - N/A;...
  • Page 9: Mig C141

    4.2.1 Mig C141 - 9 - ba47e...
  • Page 10: Mig C151

    4.2.2 Mig C151 - 10 - ba47e...
  • Page 11: Mag C171/C201/C251

    4.2.3 Mag C171/C201/C251 Electrical installation - 11 - ba47e...
  • Page 12: Mains Power Supply

    Mains power supply Check that the unit is connected to the correct mains power supply voltage, and that it is protected by the correct fuse size. A protective earth connection must be made, in accordance with regulations. Rating plate with supply connection data Recommended fuse sizes and minimum cable areas Mig C141 Mig C151...
  • Page 13: Connection And Control Devices

    WARNING Secure the equipment - particularly if the ground is uneven or sloping. Connection and control devices Mains supply switch with indicator lamp, Return cable with clamp, fixed, only in C171/C201/C251 only in C140/C150/C170/C200 Orange indicator lamp, overheating Knob for spot welding - ON/OFF and time setting, only in C171/C201/C251 Welding voltage switch Knob for wire speed setting...
  • Page 14: Welding Without Gas

    Welding without gas (Fe) (Al) (cored) (CuSi) connected when delivered (cored) Wire feed pressure Start by making sure that the wire moves smoothly through the wire guide. Then set the pressure of the wire feeder's pressure rollers. It is important that the pressure is not too great.
  • Page 15: Overheating Protection

    Overheating protection When the machine is switched on with the mains switch, [1] or [3] depending on machine model, indicator lamp [1] is on and lamp [2] off - the machine is ready to operate. If the internal temperature becomes too high, the welding is interrupted and disabled. This state is indicated by lighting of the orange indicator lamp [2] on the front of the machine.
  • Page 16: Fault Tracing

    Spare parts may be ordered through your nearest ESAB dealer, see the last page of this publication.
  • Page 17: Diagram

    Diagram - 17 - © ESAB AB 2012 ba47diag...
  • Page 18 - 18 - © ESAB AB 2012 ba47diag...
  • Page 19 - 19 - © ESAB AB 2012 ba47diag...
  • Page 20 - 20 - © ESAB AB 2012 ba47diag...
  • Page 21 - 21 - © ESAB AB 2012 ba47diag...
  • Page 22 - 22 - © ESAB AB 2012 ba47diag...
  • Page 23: Order Number

    0349 311 180 Origo Mig C151 0349 311 280 Origo Mig C171 0349 311 290 Origo Mig C201 0349 311 420 Origo Mig C251 Technical documentation is available on the Internet at www.esab.com - 23 - © ESAB AB 2012 ba47o...
  • Page 24: Wear Parts

    In order to weld with aluminium wires, proper rollers, nozzles and liners for aluminium wires MUST be used. It is recommended to use 3m long welding gun for aluminium wires, equipped with appropriate wear parts. - 24 - © ESAB AB 2012 ba47w1...
  • Page 25 In order to weld with aluminium wires, proper rollers, nozzles and liners for aluminium wires MUST be used. It is recommended to use 3m long welding gun for aluminium wires, equipped with appropriate wear parts. - 25 - © ESAB AB 2012 ba47w2...
  • Page 26: Accessories

    Mig C141/ C151 Mag C171/ C201/ C251 Accessories Digital meter 0349 302 598 Transformer kit for CO 0349 302 250 heater, 42V Traction kit for C141 0349 309 073 - 26 - © ESAB AB 2012 ba47a...
  • Page 27 - 27 - hints...
  • Page 28 - 28 - hints...
  • Page 29 - 29 - hints...
  • Page 30 - 30 - hints...
  • Page 31 - 31 - hints...
  • Page 32 ESAB Romania Trading SRL ESAB VAMBERK s.r.o. SOUTH AFRICA ESAB Mexico S.A. Bucharest Vamberk ESAB Africa Welding & Cutting Ltd Monterrey Tel: +40 316 900 600 Tel: +420 2 819 40 885 Durbanvill 7570 - Cape Town Tel: +52 8 350 5959...

Table of Contents