Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Weber mt CF 3 HD
Summary of Contents for Weber mt CF 3 HD
- Page 1 Operating and Maintenance Manual CF 3 HD Honda GX 160 Weber Maschinentechnik GmbH Im Boden 5 - 8 , 10 D-57334 Bad Laasphe-Rückershausen / Germany Tel.: + 49 (0) 27 54 / 398 0 Fax: + 49 (0) 27 54 / 398 101 E-Mail: info@webermt.de...
- Page 2 CF 3 HD...
-
Page 3: Table Of Contents
Safety guidelines Graphic presentation Device description Technical data Activities prior to starting work Starting Compacting Shutting down Maintenance overview Maintenance work Operating fluids and fill levels Troubleshooting Measures to be taken if stored for long periods Contact addresses CF 3 HD... -
Page 4: Introduction
You can obtain information on the assembled Honda petrol engine and find a spare-part list for it at www.honda-engines-eu.com The valid conformity declaration is enclosed with every machine delivery. CF 3 HD... -
Page 5: Safety Guidelines
This machine is capable of exceeding the permissible sound level of 80 dB(A). The owner might also face additional dangers when using the machine. Precautionary action must, therefore, be taken. Protective equipment includes: Ear protection Hard hat Safety shoes Protective gloves CF 3 HD... - Page 6 Do not position yourself or work under suspended loads. If lubricating oils and fuel come into contact with skin, they can cause skin cancer. Upon contact with the skin, clean affected skin with suitable cleaning agent without delay. CF 3 HD...
- Page 7 Important information for operating and maintenance personnel is marked by pictograms. Warning against irritants or materials hazardous to health Warning against a hazardous place Warning against a suspended load Wear ear protection General regulation Environmental protection Hard hat Safety shoes Protective gloves CF 3 HD...
-
Page 8: Graphic Presentation
Graphic presentation Overall view CF 3HD 1 Water tank 2 Engine 3 Handle 4 Under carriage 5 Engine bracket 6 Base plate 7 Wear ear protection (Stickers) 8 Gas lever 9 Exciter CF 3 HD... -
Page 9: Device Description
Start the Honda gasoline engine with the attached reversing starter. After starting, vibration is switched on via the centrifugal clutch attached to the engine. Use the gas lever to vary the engine speed between idle and full throttle. The machine is steered with the handle. CF 3 HD... -
Page 10: Technical Data
Technical data CF 3 HD Weight Operating weight CECE in kg (basic device) Dimensions 1160 Overall length in (in mm) Overall width/with attachment plates (in mm) Height with folded manual guidance rod (in mm) Base plate length (base in mm) - Page 11 1Description 2 TYPE ....................... 3 Serial-Number 4 Year of construction ......................5 Mass 6 Rated power KW CF 3 HD...
-
Page 12: Activities Prior To Starting Work
Slide the hand truck under the base plate. Use the handle (1) to tilt the machine to the front and swivel the undercarriage (2) beneath the base plate (3). Never transport a hand guide rod to be cocked. CF 3 HD... - Page 13 Attach the Poly pad (1) to the rear of the base plate (2). Fasten the Poly pad with holder, screws, spring-lock washers and nuts on the base plate front and rear. Ensure that the Poly pad rests under the base plate. CF 3 HD...
-
Page 14: Starting
Allow the handle (1) to slide back into the initial position, and then forcefully and completely pull it through with both hands. After the engine has warmed up, slide the choke lever (2) to the right (open). CF 3 HD... -
Page 15: Compacting
Push the fuel cock (2) to the right (close). Turn the short-circuit button (1) to the „0“ - OFF position. During breaks—even if they are short—the machine must be shut down. Parked devices that represent an obstacle must be safeguarded against conspicuously. CF 3 HD... -
Page 16: Maintenance Overview
If lubricating oils and fuel come into contact with skin, they can cause skin cancer. Upon contact with the skin, clean affected skin with suitable cleaning agent without delay. If accessible during maintenance, check the condition and stability of all screws. CF 3 HD... -
Page 17: Maintenance Work
Clean the air filter insert in accordance with theguidelines provided by the engine manufacturer, or replace if there is extreme fouling. Dispose of oils, oil-soaked cloths, and parts replaced and smeared with oil in an environmentally friendly manner. CF 3 HD... - Page 18 Checking the V-belt Remove the V-belt guard (1). Check the V-belt (1) for cracks, damaged flanks, and wear. If there is excessive wear - replace the V-belt as specified in the repair manual. CF 3 HD...
-
Page 19: Operating Fluids And Fill Levels
Operating fluids and fill levels Subassembly Fuel Quantity Summer Winter CF 3 HD Quality Engine SAE 10 W 40 Engine oil 0,6 l (-10 ~ + 50 °C) API - CD CE-CF-CG or SHPD or CCMC - D4 - D5 - PD2... - Page 20 CF 3 HD...
- Page 21 CF 3 HD...
-
Page 22: Measures To Be Taken If Stored For Long Periods
Check fuel filter, change if necessary All bare parts/accelerator/accelerator - Oil/grease control cable/fastening bolts If the machine is to be stored for longer than six months, then contact the Weber service organi- zation to discuss additional measures. CF 3 HD... - Page 23 278 01 Kralupy nad Vitavou E-Mail info@webermt.cz WEBER MT Telefon + 1(207) - 947 - 4990 USA and 4717 Broadmoor Ave. SE Suite B Telefax + 1(207) - 947 – 5452 Canada Grand Rapids, MI 49512 E-Mail sales@webermt.us service@webermt.us CF 3 HD...
- Page 24 > Vibration rollers > Joint cutters > Internal vibrators and converters > Rollers Weber MASCHINENTECHNIK GmbH Im Boden 57334 Bad Laasphe - Rückershausen Telephone + 49 27 54 / 398 0 - Fax +49 27 54 / 398 101 CF 3 HD...