Subscribe to Our Youtube Channel
Related Manuals for Alfa IN 5.0238-2
Summary of Contents for Alfa IN 5.0238-2
- Page 1 - 1 - WELDING INVERTER PEGAS 200 AC/DC PULSE OPERATING MANUAL ALFA IN a.s. © www.alfain.eu PEGAS 200 AC-DC PULSE ovo manual ENG 11...
-
Page 2: Table Of Contents
OPERATOR CONTROLS ................8 GETTING STARTED ................. 10 TWO STROKE AND FOUR STROKE IN TIG MODE ....... 13 ROUTINE MAINTENANCE & INSPECTION ..........14 STATEMENT OF WARRANTY ..............15 10. DISPOSAL ....................15 11. WARRANTY LIST ..................16 ALFA IN a.s. © www.alfain.eu... -
Page 3: Introduction
1. INTRODUCTION Congratulations on your new ALFA IN product. We are proud to have you as our customer and will strive to provide you with the best service and reliability in the industry. This Operating Manual has been designed to instruct you on the correct use and operation of your ALFA IN product. -
Page 4: Safety Instructions And Warnings
Do not work in a damp or humid environment. Do not use the welding machine if its cables are damaged in any way. Make sure that the earthing system of the electric equipment is correctly ALFA IN a.s. © www.alfain.eu... - Page 5 It meets the requirements of EN 60974-10 class A and it isn’t designed for using in residential areas, where the electrical energy is supplied by public low-voltage power supply network. It can be here potential problems with ensuring of electromagnetic compatibility in this areas, due to interference ALFA IN a.s. © www.alfain.eu...
-
Page 6: Technical Data
Mains voltage V/Hz 1x230/50-60 Welding current range 10 - 20 5 - 200 Open-circuit voltage U Welding current (DC=100%) I ta=40 °C Welding current (DC=60%) I ta=40 °C Welding current (DC=x%) I 20%=200 25%=200 ta=40 °C ALFA IN a.s. © www.alfain.eu... -
Page 7: Equipment
30%=200 ta=25 °C ALFA IN continuously strives to produce the best product possible and therefore reserves the right to change, improve or revise the specifications or design of this or any product without prior notice. Such updates or changes do not entitle the buyer of equipment previously sold or shipped to the corresponding changes, updates, improvements or replacement of such items. -
Page 8: Operator Controls
LED ratio of the pulse current and the base current . 5 – 100 %. Default 5 %.Just for the pulse mode. Display Voltage, %, time and Hz. LED Main Welding Current in the pulse mode. 5 – 200 A DC, 10 – 200 TIG AC ALFA IN a.s. © www.alfain.eu... - Page 9 Button switch Pulse/Non pulse mode. LED Pulse. If illuminated the Pulse mode was set. LED HF. If illuminated the HF ignition was set. LED Gas Test. If illuminated the mode of setting the gas flow was ALFA IN a.s. © www.alfain.eu...
-
Page 10: Getting Started
Prevent touching the electrode any metal material for in this mode the terminals 42 and 44 are under current. 8. Insert the coated electrode into the electrode holder, connect the clamps of the ground cable to the welding piece and you may start welding. ALFA IN a.s. © www.alfain.eu... - Page 11 3 s. More in the table MAIN PARTS above. Connect the work clamp to the work piece or at the welding table and you can start welding. The following table describes the influence setting the clearance ALFA IN a.s. © www.alfain.eu...
- Page 12 3. Standard separate remote control for changing the value of the welding current. All three models of remote controls can be connected by means of the front panel connector 43. Fig . 2 Foot pedal remote control ALFA IN a.s. © www.alfain.eu...
-
Page 13: Two Stroke And Four Stroke In Tig Mode
3. The welding process ends after releasing the stepping surface P1. 7. TWO STROKE AND FOUR STROKE IN TIG MODE TWO STROKE – 2T Welding current Down slope Current Postgas Pregas FOUR STROKE – 4T ALFA IN a.s. © www.alfain.eu... -
Page 14: Routine Maintenance & Inspection
The person carrying out the servicing needs and repairs must know what to look at, what to look for and what to do. ALFA IN a.s. © www.alfain.eu... -
Page 15: Statement Of Warranty
The warranty period begins on the date of sale to the end user. If warranty is being sought, please contact your ALFA IN product supplier for the warranty repair procedure. -
Page 16: Warranty List
As a warranty list serves proof of purchase (invoice) on which is the serial number of the machine, eventually a warranty list below, which is filled in by an authorized dealer. Serial number: Day, month (written in words) and year of sale: Stamp and dealer signature: ALFA IN a.s. © www.alfain.eu...
Need help?
Do you have a question about the 5.0238-2 and is the answer not in the manual?
Questions and answers