Subscribe to Our Youtube Channel
Related Manuals for Alfa IN PEGAS 160 E PFC
Summary of Contents for Alfa IN PEGAS 160 E PFC
- Page 1 - 1 - WELDING INVERTER PEGAS 160 E PFC OPERATING MANUAL ALFA IN a.s. © www.alfain.eu NA137-3...
-
Page 2: Table Of Contents
GETTING STARTED MMA – COATED ELECTRODE......9 GETTING STARTED TIG LIFT ARC...........9 7.2.1 How to connect the gas cylinder............9 7.2.2 Basic settings for TIG welding – stainless steel, DC current ..10 ROUTINE MAINTENANCE & INSPECTION..........10 STATEMENT OF WARRANTY..............11 10 DISPOSAL....................11 ALFA IN a.s. © www.alfain.eu... -
Page 3: Introduction
INTRODUCTION Congratulations on your new ALFA IN product. We are proud to have you as our customer and will strive to provide you with the best service and reliability in the industry. This Operating Manual has been designed to instruct you on the correct use and operation of your ALFA IN product. - Page 4 The operator must be insulated from the metal components connected to the return wire. • The earthing of the piece being worked could increase the risk of injury to the operator. • EN 60974-1 Standard: Open-circuit voltage. During the operation of the ALFA IN a.s. © www.alfain.eu...
-
Page 5: Electromagnetic Compatibility (Emc)
• Domestic electronic appliances (radios, TVs, videos, telephones, burglar alarms, etc.). • Computers, robots, electro-medical instruments and life-support systems. • Radio-television transmitters and receivers. • Pacemakers and hearing aids. ALFA IN a.s. © www.alfain.eu... -
Page 6: Technical Data
P 1max ALFA IN continuously strives to produce the best product possible and therefore reserves the right to change, improve or revise the specifications or design of this or any product without prior notice. Such updates or changes do not entitle the buyer of equipment previously sold or shipped to the corresponding changes, updates, improvements or replacement of such items. -
Page 7: Equipment
VM0253 Welding Cable Set 2x 3m 35-50 160A 5.0110 Box blue 4281 Valve Red.AR /CO2, 2 manometers,MINI S777a Light Reactive Welding Helmet ALFA IN S777a GRAY 705.0307 Torch ABITIG 26 4m V 35-50 705.0308 Torch SR26 8m V 35-50 705.0172 Torch SR17 4m V 35-50 705.0173... -
Page 8: Operator Controls
OPERATOR CONTROLS Fig . 1 Main parts FRONT PANEL Pos. Description LED ON LED over heating Current potentiometer Method switch MMA (electrode)/TIG Cooling ribs Panel quick connector + Mains socket with a pulg ON/OFF switch ALFA IN a.s. © www.alfain.eu... -
Page 9: Getting Started
Open the gas cylinder valve, open the valve on the TIG torch and adjust the gas flow on the gas regulator. The flow rate will be shown at the flow meter. This should be done according the table below. ALFA IN a.s. © www.alfain.eu... -
Page 10: Basic Settings For Tig Welding - Stainless Steel, Dc Current
Troubleshooting and repairing of PEGAS welding equipment should only be carried out only by suitably qualified or competent person. • A ‘competent person’ must be a person who has acquired through training, qualification or experience, or a combination of them, the knowledge and ALFA IN a.s. © www.alfain.eu... -
Page 11: Statement Of Warranty
• ALFA IN will repair or replace, at its discretion, any warranted parts or components that fail due to defects in material or workmanship within the warranty period. The warranty period begins on the date of sale to the end user. - Page 12 ALFA IN a.s. © www.alfain.eu...
Need help?
Do you have a question about the PEGAS 160 E PFC and is the answer not in the manual?
Questions and answers