Summary of Contents for RADLEY 1282-201
- Page 1 OWNER’S MANUAL 3 Year Limited Warranty READ ALL INSTRUCTIONS BEFORE FIRST USE. KEEP THIS MANUAL FOR FUTURE REFERENCE. KEEP AWAY FROM CHILDREN. WEAR CSA APPROVED WEAR EAR WEAR FACE PROTECTION PROTECTION EYE PROTECTION...
- Page 2 Magazine Capacity 100 Nails 18 Gauge /8 - Fastener Capacity Long 120PSI Max PSI Average Air Consumption 0.5 CFM @ 90PSI Working pressure 60-100 PSI Magazine angle 90° Air inlet size Recommended hose size 1/4" or 3/8" Weight 3.08lb (1.4 kg) Call us on our toll-free customer support line: 1-866-349-8665 (Monday through Friday 9am –...
- Page 3 Product Speci cations ..................1 Table of Contents ....................2 Safety Guidelines ....................3-5 Symbols ........................6 Tool speci c arnings ................... 7 Know your 18-gauge pneumatic brad nailer ............8 Assembly and Operating ................9-14 Maintenance ....................15-18 Exploded View ..................... 19 Parts List ......................
- Page 4 This manual contains information that relates to PROTECTING PERSONAL SAFETY and PREVENTING EQUIPMENT PROBLEMS. It is very important to read this manual carefully and understand it thoroughly before using the product. The symbols listed below are used to indicate this information. Potential hazard that will result in serious injury or loss of life.
- Page 5 Do not use oxygen or any other combustible or bottled gas to power air-powered tools. Failure to observe this warning Oxygen can cause explosion and serious personal injury or death. Hydrogen Use only the compressed air to power the air-powered tools.
- Page 6 Keep children away from the work area. Do not allow children to handle power tools. Do not use this tool in the presence of ammable liquids or gases. Sparks that are created during use may ignite gases. Keep air hose away from heat, oil, and sharp edges. Check air hose for wear before each use and ensure that all connections are proper.
- Page 7 before performing any maintenance or changing accessories, when clearing a jammed fastener, when the tool is not in use, when it is being handed to another person, and when it is left unattended. Failure to comply may result in moderate injury or damage to equipment.
- Page 8 ...
- Page 10 The 18 Gauge pneumatic Brad Nailer is ideal for fastening all types of trim and molding around the house. The lightweight, narrow body tool is easy to handle, making it ideal for oor molding and cabinet trim. The brad nailer has a 100-brad magazine that res 18-gauge brads from /8 to Be sure to use a proper air compressor with air-powered tools.
-
Page 11: Air Compressor
Always use clean, dry, regulated, compressed air at 4.1 to 6.9bar (60-100PSI) Do not exceed the maximum or minimum pressures. Operating the tool at the wrong pressure (too low or too high) will cause excessive noise or rapid wear of tool. 18-gauge pneumatic brad 0 to 6.9 bar nailer... - Page 12 Read and follow all the safety instructions at the beginning of this manual. Inspect the air- powered tool prior to each use in order to: -Ensure that the proper power source is being used. -Verify that the tool is in proper working order. -Verify that the air pressure level (s) are properly set on the air compressor.
- Page 13 2.Hold the Brad Nailer rmly with onehand and use the other hand to press the latch (1) on the magazine (2) and slide it back. 3.Insert a strip of nails (1) into the magazine. After ensuring that the points of the nails are facing down, close the magazine.
- Page 14 The Brad Nailer has a depth adjustment dial below the trigger to adjust the ring depth of the fasteners. Note: Refer to the graphic imprinted below the trigger and adjust the ring depth accordingly. Turn the depth adjustment dial counterclockwise (with the discharge area of the tool facing away from the operator).
- Page 15 the Workpiece Contact will cause a fastener to be driven. ⚠ WARNING Extreme care should be taken because a nail will be driven when the firing head contacts any surface. Remove the non-jammed nails that are stored in the tool’s magazine. Operate the magazine latch and slide the pusher back to open the magazine for checking the jammed nails.
- Page 16 General inspection - Trigger, spring, None Worn or broken In-depth inspection parts Replace worn or broken parts Pneumatic See below Lubrication tool oil Lubrication: If the Air-powered brad nailer and the compressor are not equipped with an in-line lubrication system, place 2 to 3 drops of pneumatic tool oil into the air inlet before each use or after every 2 hours of continuous use, depending on the characteristics of the workpiece...
- Page 17 • Inspect the trigger, spring, and the safety mechanism for free movement on a regular basis in order to ensure that the safety system is fully functional. Verify that no part is loose or missing and that no parts are sticking or jammed. •...
- Page 18 1. The bumper is worn. 1. Replace the bumper. The nails are 2. The air pressure is 2. Adjust the air pressure. being driven too high. 3. Adjust the depth setting by turning too deep. 3. The depth the depth adjustment knob adjustment knob is counterclockwise (see section not adjusted...
- Page 19 1. Use proper nails. 1. Improper nails are (See section Clearing a jammed nail. ) used, or nails are The tool jams. 2. Inspect and replace the driver. damaged. 3. Tighten the magazine. 2. The driver guide is 4. Open and clean the magazine. damaged or worn.
- Page 21 When servicing, use only original equipment replacement parts. The use of any other parts may create a safety hazard or cause damage to the tool. Any attempt to repair or replace electrical parts on this tool may create a safety hazard unless repairs are performed by a quali ed technician. For more information, call the Toll-free Helpline, at 1-866-349-8665.
- Page 24 If this Radley tool fails due to a defect in material or workmanship within three years from the date of purchase, return it to any Home Hardware store with the original bill of sale for exchange. Two years for battery and charger. This warranty does not include expendable parts including but not limited to blades, brushes, belts and light bulbs.
- Page 25 OWNER’S MANUAL 3 Year Limited Warranty on tool 1282-201 RADLEY TOOLS READ ALL INSTRUCTIONS BEFORE FIRST USE. KEEP THIS MANUAL FOR FUTURE REFERENCE. KEEP AWAY FROM CHILDREN. WEAR CSA APPROVED WEAR EAR WEAR FACE EYE PROTECTION PROTECTION PROTECTION...