Related Manuals for SolarEdge Home Battery 48V
Summary of Contents for SolarEdge Home Battery 48V
- Page 1 Home Battery 48V Installation Guide MAN-01-00954-1.1 For Europe and APAC Version 1.1...
-
Page 2: Disclaimers
The images contained in this document are for illustrative purposes only and may vary depending on product models. This manual describes installation of theSolarEdge Home Battery 48V . Read this manual before you attempt to install the product, and follow the instructions throughout the installation process. -
Page 3: Table Of Contents
Installing the Battery Modules Battery description Installation procedure Connecting a Single Battery Module Connecting Multiple Battery Modules Powering on the Battery Module Top Cover Installation Adding or Removing a Battery Module LED Indications Support Contact Information Home Battery 48V Installation Guide MAN-01-00954-1.1... -
Page 4: Revision History
Revision History 3 Revision History Version 1.0 (June 2022) First version of this guide Version 1.1 (January 2023) Various updates Home Battery 48V Installation Guide MAN-01-00954-1.1... -
Page 5: Handling And Safety Instructions
Handling and Safety Instructions Handling and Safety Instructions Read these instructions carefully before installing or operating the SolarEdge Home Battery 48V (referred to as the Battery or Battery Pack ). Failure to do so or to follow any of the instructions or warnings in this document can result in electrical shock, serious injury, or death, or may damage the battery and other property. -
Page 6: Operation
WARNING! In case of an electrolyte leak from the battery, avoid contact with electrolyte and follow the instructions in the SolarEdge Home Battery 48V Emergency Response Guide. WARNING! Use the battery only as directed in this document. - Page 7 WARNING! Do not use fluids, parts, or accessories other than those specified in this guide, including use of non-genuine SolarEdge parts or accessories, or parts or accessories not purchased directly from SolarEdge or a SolarEdge certified party.
- Page 8 Ensure that snow does not accumulate around the battery. WARNING! A non-functioning battery must be handled with caution. The battery state of charge and risk of venting may be unknown. Contact SolarEdge for assistance. WARNING! Do not attempt to remove or transport a damaged or non-functioning battery.
-
Page 9: Installation Tools
Make sure you have the following tools, before starting the installation: Crimping tool Torque wrench Drilling machine Level Phillips screwdriver Flat-blade screwdriver Cable cutter Wall plugs and screws Hammer Charging cable requirements Conductor cross section - 35mm Outer diameter 14-21mm maximum cable length 5m Home Battery 48V Installation Guide MAN-01-00954-1.1... -
Page 10: What's In The Package
IAC-RBAT-5KCINV-02 Phase (PN SE*K-RWS48) Accessory SolarEdge Home Battery 48V , cable set battery IAC-RBAT-5KCBAT-01 module to battery module Accessory SolarEdge Home Battery 48V , cable set tower to IAC-RBAT-5KCTOW-01 tower Floor stand support SolarEdge Home Battery 48V (optional) IAC-RBAT-5KFSTD-01 Accessory 10 * Spare connector kit for battery to Inverter... -
Page 11: Selecting And Preparing The Installation Site
The term Battery pack or Battery refers to all the battery modules connected to each other and to the same inverter, in one or two towers. Connect up to 5 battery modules in two towers (maximum 3 in a tower). Home Battery 48V Installation Guide MAN-01-00954-1.1... -
Page 12: General Guidelines And Requirements
Do not install the battery at any of following locations: residential rooms wall or ceiling niches entrance/exit areas or below a staircase/passage environments with humidity and condensed water level of over 90% earthquake zones where additional safety measures are required Home Battery 48V Installation Guide MAN-01-00954-1.1... -
Page 13: Clearance
20 cm from air vents 20 cm from other devices WARNING! Connect no more than 5 batteries per inverter. Use no more than 3 batteries per battery tower. NOTE The distance between the battery tower and Home Battery 48V Installation Guide MAN-01-00954-1.1... -
Page 14: Residential Barrier
If the installation surface is not made of a non-combustible material, a non-combustible barrier can be installed between the battery and the wall or structural surface. Home Battery 48V Installation Guide MAN-01-00954-1.1... - Page 15 If the Battery pack is installed on a wall or at a distance of 300mm from the wall that isolates the energy storage system from a residential space, the distance from other structures or objects must be increased. Home Battery 48V Installation Guide MAN-01-00954-1.1...
-
Page 16: Installing The Battery Modules
Not to be used to inverter communication. RS485 Communication socket to connect the DC bat - connectors battery module below to this battery module (in a battery tower) DC bat + connector Home Battery 48V Installation Guide MAN-01-00954-1.1... -
Page 17: Installation Procedure
Installation procedure 1. Install a floor stand. Floor stand is optional, however, for durable and robust insulation, SolarEdge recommends to install the battery modules on top of a floor stand, to be purchased seperately from SolarEdge. Depending on wall leveling, consider when installing more than one module. - Page 18 3. Place the battery module on the floor stand using the top handles. Make sure that the battery stands firmly, and not shaky, on the floor stand. Figure 7: Top handles Home Battery 48V Installation Guide MAN-01-00954-1.1...
- Page 19 Figure 9: Setting the distance from the wall 6. Secure the battery module to the wall with screws and wall plugs. When using only two screws, make sure to use the two outer screws diagonally as shown on the figure below. Home Battery 48V Installation Guide MAN-01-00954-1.1...
- Page 20 Secure all battery modules to the wall as described above. Note that the maximum allowed amount of battery modules in a tower is three. Figure 11: Installing battery modules in a tower configuration Home Battery 48V Installation Guide MAN-01-00954-1.1...
-
Page 21: Connecting A Single Battery Module
IAC-RBAT-5KCINV-02 (to Inverter Wave Inverter) Tower to IAC-RBAT-5KCTOW-01 Tower Module IAC-RBAT-5KCBAT-01 Module (Same Tower) If you need a longer cable, you will have to crimp the connectors yourself using one of the following kits: Home Battery 48V Installation Guide MAN-01-00954-1.1... - Page 22 4. Before continuing with the installation, make sure the battery is OFF, then make sure that the front panel LEDs are OFF. If the battery is on, first turn OFF the CB, then the soft switch, as follows: Home Battery 48V Installation Guide MAN-01-00954-1.1...
- Page 23 b. Press the power button (soft switch, position 4 below) for 3-6 seconds until the indicator lights go out. Figure 14: Battery LED indicators Battery Capacity/ Alarm ID Indication LED Operation Indicator Power/Reset Button Home Battery 48V Installation Guide MAN-01-00954-1.1...
- Page 24 5. Connect the CAN-bus communication cable (RJ45) coming from the inverter, with the top battery module connector marked "Inverter". It is important to distinguish between the inverter communication port and any other module to module communication ports. Figure 15: Connecting the communication cable Home Battery 48V Installation Guide MAN-01-00954-1.1...
- Page 25 BAT+) to connect power from the inverter. Note the polarity. Insert the connectors into this socket until you hear a click. Figure 17: Connecting power from the inverter 8. Figure below shows the single battery module with completed connections. Home Battery 48V Installation Guide MAN-01-00954-1.1...
- Page 26 3-6 seconds, the LEDs will light. If this is a new battery (e.g. not RMA) only the first green LED or the first and second green LED should light constantly. No other LEDs should light. If you observe a different LEDs sequence, Home Battery 48V Installation Guide MAN-01-00954-1.1...
- Page 27 Connecting a Single Battery Module refer to for LED troubleshooting, or contact SolarEdge support with the Battery module SN and the LED sequence. Until this is solved, do not proceed with the installation. Figure 19: Battery LED indicators Battery Capacity/ Alarm ID...
-
Page 28: Connecting Multiple Battery Modules
Use only cables recommended by SolarEdge—see Connecting a Single Battery Module on page 20 Contact SolarEdge or your distributor to order the appropriate cable kit for your configuration. For cable kits and accessories, see What's in the Package on page 9. - Page 29 Figure 20: Connecting cables between the battery modules 4. Connect the DC and communication cable of the first or last battery module to the inverter. For ease of installation, SolarEdge recommends to connect the inverter to the top battery module. See the inverter installation guide for connection instructions.
-
Page 30: Powering On The Battery Module
Figure 21: Battery LED indicators Battery Capacity/ Alarm ID Indication LED Operation Indicator Power/Reset Button 2. Turn on the DC switch. Figure 22: Turning on the DC switch 3. Fasten the side door with the three screws. Home Battery 48V Installation Guide MAN-01-00954-1.1... -
Page 31: Top Cover Installation
3. Place the frame on top of the top battery module in the tower, secure it with the 3 screws provided in the kit 4. Assemble the top plate with the 5 screws. Figure 23: Top Cover Installation Home Battery 48V Installation Guide MAN-01-00954-1.1... -
Page 32: Adding Or Removing A Battery Module
5. Power on the battery module, see Powering on the Battery Module on page 29. The added module may have different SoC level than the existing modules, this is normal and will be balanced after a few charge/discharge cycles . Home Battery 48V Installation Guide MAN-01-00954-1.1... -
Page 33: Led Indications
LED Indications LED Indications The following section describes the LED behavior of the SolarEdge Home Battery 48V. Mode Behavior Operational LED is ON or Blinking once Normal operation of the battery NO other cases of operational LED Alarm – there is an alarm, but... - Page 34 Off On Heating fault 3 blinks Off Off Low SoC 3 blinks On On Temperature sensor 3 blinks On Off malfunction Battery Cell 3 blinks Off On malfunction Communication 3 blinks Off Off failure Home Battery 48V Installation Guide MAN-01-00954-1.1...
- Page 35 3 blinks Off On Temperature Ambient Under 3 blinks Off Off Temperature Mosfet Over 3 blinks On On Temperature Reserved 3 blinks On Off Reserved 3 blinks Off On Battery Locked 3 blinks Off Off Home Battery 48V Installation Guide MAN-01-00954-1.1...
- Page 36 LED Indications 35 Blink Mode Blinks once every 4 seconds 0.25S 3.75S Blinks three times every 6 seconds 0.5S 1.5S Home Battery 48V Installation Guide MAN-01-00954-1.1...
-
Page 37: Support Contact Information
System configuration information, including the type and number of panels connected and the number and length of strings. The communication method to the SolarEdge server, if the site is connected. The product's software version as it appears in the ID status screen. - Page 38 ...