Rola RMX430 Manual

x2 x2
END SUPPORT END SUPPORT
(RIGHT) (LEFT)
Phillips Head Screwdriver
ASSEMBLY OF CROSS-BARS
1. Ensure the roof is clean, free from dust and grease.
2. Insert the neck of the End-Support into the void of the Cross-bar pro le.
They are designed to be a tight t: use a rubber mallet if necessary (Fig.1)
3. Pull back the rubber Bu er Strip about 20mm until the screw hole can be
accessed.(Fig. 2) Using a Phillips Head Screwdriver, fasten the screw through
the cross-bar and into the End Support.
Do this for all four sides and replace the bu er strip.
NOTE: The longer cross-bars are to be tted to the front of the vehicle. Check
labelling on the underside of the cross-bar.
ASSEMBLY OF CROSS-BARS
STEP 1: On the vehicle roof you will nd 4 Anchor Point Covers paired in two
locations indicated by the arrows in Fig 3.
Carefully remove these covers by sliding in the direction shown on the cover,
to reveal the anchor points as seen in Fig 4.
NOTE:
Take care when removing to avoid damaging Trim Cover Clip. Covers can
not be replaced while rack is tted.
For a Single-Bar tment, only remove the two Front or the two
Store the Anchor Point Covers and plugs safely while the Roof Racks are in use.
STEP 2
Revealing the anchor points you will notice a slot with folded ends closest to the
begining of the weather strip Fig 5. This tment will hook into these folded ends
and brace o a backing plate.
STEP 3
Place a Backing Plate (Part No. 22-0837) into the anchor point. This will self locate
into the bigger slot of the two as seen in Fig. 6
STEP 4
Now that the backing plate is seated into the anchor point. Place straps 9018 and
9019 directly on top of the backing plate. Then slide them into the outward
direction as seen Fig 7. The elongated end of the strap will slide into the smaller
slot and will be concealed by the folded end of the anchor point.
STEP 5
Secure straps 9018 and 9018 onto the backing plate using the M5x10 black xylan
bolts supplied Fig. 8. This kit comes wth the appropriated allen key to do so. After
completing this your anchor point should should appear as seen in Fig. 9
STEP 6
You are now ready to mount your cross bar assembly to the vehicle. Place the
front crossbar (usually the longer of the two or has label saying "FRONT" on the
underside of the roof bar) over the anchor points. Aligning the holes of the end
support and anchor point secure the bars to the roof using the M6 x 50 security
bolt provided. Use the the rubber sleeve provided to conceal the bolt. as per Fig.
10.
Repeat for the remaining anchor points and rear cross bar. You are now ready to
mount your "Accessories" set on to the cross-bars using the Global Mount
Channel. Once installed , insert the 'Global Channel' covers into the end supports.
Issue A
RMX430
19/08/13
RMX Series Roof Racks
VE & VF Commodore
Sedan & Sportswagon without Sunroof
x2 x2
MOUNT PAD MOUNT PAD SNAP-ON
(RIGHT) (LEFT)
Please Note: You will require the following tools
Flat Head Screwdriver
Holden
08/06 Onwards
9019
9018
x4
x4 x4
SECURITY STRAP
COVER COVER BRACKET
Rubber Mallet
Fig. 1
Fig. 3
Figure. 5
(9019)
Fig. 7
Fig. 9
M6 Anchor Point
CARRYING CAPACITY
x4 x4 x4
M6x45 M5x10
SECURITY XYLAN ASSEMBLY
22-0846
BACKING PLATE
BOLT BOLT
Safety Knife
Fig. 2
Fig. 4
Figure. 6
Fig. 8
(9018)
M5x10
Figure 4a.
Fig. 10
YOUR ANCHOR POINT
ACCESS MAY LOOK DIFFERENT
TO THIS ILLUSTRATION
RMX430
60 kg
x2
x1
CROSS-BAR ASSEMBLY
KEY
Screw
Screw hole
A
ANCHOR POINT
COVER
FULLY
or
REMOVE
SLIDE
B
(22-0837)
Quick Access
Snap-on Cover
THREADED
ANCHOR HOLE
page 1 of 3