SOMFY J4 io Protect Quick Start Installation Manual

GUIDE TO FOLLOW
This quick-start guide, intended for the installer, presents the key
operations to be performed when installing the drive.
A complete manual is also available online at
more information. This document provides information regarding
the assembly operations performed by the manufacturer of the
load-bearing product, and the steps necessary to replace a drive in
an existing installation, for example.
· Several adjustments are made using the
CD
tools, notably setting the type of EVB for optimum control with
. Somfy home automation systems.
These instructions apply to the J4 io Protect
drives, which area available in the current
catalogue.
SPHERE OF APPLICATION
J4 drives are designed to drive all types of
Exterior Venetian Blinds (EVB).
The installer, a home motorisation and
automation professional,
that once the driven product is installed, it
respects the current standards in the country
of installation, notably standard EN 13561
relative to exterior blinds.
LIABILITY
Before installing and using the drive, please
read these instructions carefully. In addition to
the instructions provided in this guide, please
also· comply with the instructions set out in
the enclosed Safety instructiO!lS document.
The drive must be installed by a home
motorisation and automation professional,
in accordance with Somfy's instructions and
the applicable regulations in the country of
installation.
Any operation of the drive outside the sphere
of application described above is prohibited.
Such operation shall exclude Somfy from all
liability and invalidate the Somfy warranty, as
will any failure to comply with the instructions
given herein and in the enclosed Safety
.instructions document.
After installing the drive, the installer must
inform his customers of the operating and
maintenance conditions for the drive and
must pass the operating and maintenance
instructions on to them, as well as the
enclosed Safety instructions document. Any
After-Sales Service operation on the
requires intervention by a home motorisation
and automation professional.
Should any doubt arise during installation of
the drive or for additional information, coAsult
· a Somfy contact or visit www.somfy.com.
GENERAL SAFETY INSTRUCTIONS
Fitting, testing, commissioning and repair of
the installation must only be carried out by
qualified personnel.
Non contractual images
<
r-­
r--
0,.
0,.
M
in
...:
a,
0::
www.somfy.info
EMS2 and
The installation must be protected from all
unauthorised use.
. C omply with the assembly and operating
guides, in particular the safety instructions
supplied by the manufacturer of the device to
be used.
To remove the drive power cable, please
use the J4 cable removal tool supplied,
must ensure
ref:9017811.
The drive, torque and operating time must be
adjusted in relation to the whole installation.
The moving parts of the drives must be
protected if operating below 2.50 m from
ground level or another level.
Disconnect
the power supply before working on the
installation.
SAFETY INSTRUCTIONS FOR WIRING
&
Cables routed through a metal wall must
• be protected and insulated by sleeving or
sheathing.
&
Secure the cables to prevent any contact
• with moving parts.
A.. If the drive is used outdoors and if the
ill power supply cable is of the H05-WF
type, run the cable in a UV-resistant duct, e.g.
trunking.
&
Leave the dri;e power supply · cable
• accessible: it must be able to be easily
replaceable.
� Always make a loop in the power cable to
prevent water from entering the drive!
SPECIFIC INSTRUCTIONS
Correct operation of the installation is only
drive.
guaranteed if the installation and assembly
have been carried out according to best
practices, if the power supply is adequate and
if maintenance is carried out.
Do not use the installatfon if work (cleaning
windows, for example) is being carried out
nearby.
If the mushroom is used to stop the EVB in
the upper end limit position, the installer must
ensure that the mushroom is present when
(�)
•
"'-somti·'
for
www.somfy.info
Set&Go
all connected cables from
GLOSSARY
&
Safety Warning!
Caution!
�
CD
Information
/\
Local control point
my
io - Somfy
V
the complete installation is used for the first
time.
To avoid damaging the product: never
immerse it, avoid impacts, avoid dropping it
and never drill into it!
The phases and neutrals of each drive must
be connected together respectively, as shown
below:
Earth
:.:;: :i � � �
· M M
C �
As the manufacturer,
� ACTIVITES SA, F-7 4300 CL USES
hereby declares that the drive covered by
these instructions, marked for input voltage
230 V-50 Hz and used as set out in these
instructions, is in compliance with the
essential requirements of the applicable
European Directives and in particular of the
Machinery Directive 2006/42/EC and Radio
Equipment Directive 2014/53/EU. The full text
of the EU Declaration of Conformity is
available at www.somfy.com/ce. Antoine
Creze, Approval manager, acting on behalf of
the Business Director, Cluses, 12/2017 .
Alt innen solskjerming
PDF
7_3
. M -
SOMFY