Related Manuals for SOMFY J4 RTS
Summary of Contents for SOMFY J4 RTS
- Page 1 J4 RTS notice installateur Installationsanleitung guida d’installazione Installer guide...
-
Page 2: Table Of Contents
5.5. Setting the end limits 5.6. Programming the first Somfy local 9. technical data control point 1. IntRODUCtIOn The J4 RTS motor is designed to drive all types of external venetian blind. © 2011 Somfy SAS. All rights reserved. 06/2011... -
Page 3: Safety
- The motor, the torque and the operating time must be adjusted according to the complete installation. - Only Somfy original accessories should be used (adapters, brackets, connectors, power cable, etc.). - Fitting, testing, commissioning and repair of the installation must only be carried out by qualified personnel. -
Page 4: Installation
• Using the clips (5), attach the motor in the head rail (4) above the small acoustic tapes (6a). • The shaft can be fitted into the adapter using a headless screw (7). © 2011 Somfy SAS. All rights reserved. 06/2011... -
Page 5: 57 X 51 Mm Head Rail, Open Above
• Using the clips (5), attach the motor in the head rail (4). • The shaft can be fitted into the adapter using a headless screw (7). The internal clips cannot be used with J418 motors (J4 motors with a torque of 18 Nm). © 2011 Somfy SAS. All rights reserved. 06/2011... -
Page 6: 67 Mm Head Rail, Open Below
• The shaft can be fitted into the adapter using a headless screw (7). For motors with torque greater than 10 Nm • The additional clamp must be attached with a new bolt -> tightening torque ≤ 4 Nm. © 2011 Somfy SAS. All rights reserved. 06/2011... -
Page 7: 66 Mm Head Rail, Open Below
• Cut off the mains power supply. • Connect the motor according to the information in the table below: 230 V ~ 50 Hz Motor cable Neutral (N) Blue Live (P) Brown Earth ( ) Yellow/Green © 2011 Somfy SAS. All rights reserved. 06/2011... -
Page 8: Commissioning
5. COMMISSIOnIng The guide only describes commissioning using a Telis MOD/VAR type Somfy local control point. For commissioning using any other Somfy local control point, refer to the corresponding guide. 5.1. Identifying setting steps already completed Only one motor should be powered at a time. -
Page 9: Checking The Motor's Direction Of Rotation
• Press the Up button to check the direction of rotation. 5.4. Selecting the type of E.V.b. (type 1 or type 3) • The J4 RTS motor is factory set to operate with a type 1 E.V.B.. However, the user can select the operating mode for either a type 1 or type 3 E.V.B.. -
Page 10: Setting The End Limits
5.5. Setting the end limits Check that your J4 RTS actuator has been assembled in the blind in the lowered position with the slats closed. 5.5.1. End limit (automatic adjustment) • Briefly press the PROG button on the pre-programmed control: the E.V.B. moves briefly, the control point is programmed. -
Page 11: Programming The First Somfy Local Control Point
• Briefly press the PROG button on this control point: the E.V.B. moves briefly; the control point has been programmed. Checking the settings 5.7. Check the settings of the upper and lower end limits using the Somfy local control point. © 2011 Somfy SAS. All rights reserved. 06/2011... -
Page 12: Operation
• On a standard Telis type local control, 2 modes are available: EU mode and US mode. The J4 RTS motor is factory set to operate in US mode In US mode, briefly pressing the Up or Down button raises or lowers the E.V.B. -
Page 13: Operating With A Somfy Sensor
6.1.4. Selecting the mode. (EU mode or US mode) • The J4 RTS motor is factory set to operate in US mode. However, the user can choose between the EU and US modes. • Press the Up and Down buttons for 5 seconds the E.V.B. -
Page 14: Additional Settings
E.V.B. moves briefly; the "my" position is deleted (the "my" button now works only as a "STOP" button. If using a sun sensor, the E.V.B. moves to the lowered position when the sun appears). © 2011 Somfy SAS. All rights reserved. 06/2011... -
Page 15: Adding/Deleting Somfy Control Points And Sensors
7.2. Adding/Deleting Somfy RtS control points and sensors 7.2.1. Adding/Deleting an RtS control point • Find an RTS control point programmed in the motor. • Press the PROG button on the RTS control point (A) until PROG. PROG. the E.V.B.moves briefly: the motor is in programming PROG. -
Page 16: Sun Disappearing" Position
• Press the "my" button: the E.V.B. starts to move then stops in the favourite (my) position. • Press and hold the "my" and Down buttons for 5 seconds: the E.V.B. moves briefly; it will not change position when the sun disappears. © 2011 Somfy SAS. All rights reserved. 06/2011... -
Page 17: Modifying The Thumbwheel's Direction Of Rotation
• To confirm the motor's new direction of rotation, press and hold the "my" button for 2 seconds: the E.V.B. moves briefly; the motor's direction of rotation has been changed. © 2011 Somfy SAS. All rights reserved. 06/2011... -
Page 18: Modifying The End Limits
With a type 3 EVB, stop the EVB before the desired position, and adjust the limit with the thumbwheel of the local control point. • Press the Up button (the blind moves briefly to confirm programming). © 2011 Somfy SAS. All rights reserved. 06/2011... -
Page 19: Tips And Recommendations
The remote control is not compatible Pair then use a Telis Mod/VAR RTS remote easily control 8.2. Replacing a lost or broken Somfy control point This reset deletes all control points, however, it does not delete the sensors and the favourite position. -
Page 20: Restoring The Original Configuration
Operating temperature - 20°C to + 70°C Index protection rating IP 54 Maximum number of connected control points Maximum number of connected sensors Safety level Class I Torque (Nm) Motor length (mm) © 2011 Somfy SAS. All rights reserved. 06/2011... - Page 21 © 2011 Somfy SAS. All rights reserved. 06/2011...
- Page 22 SOMFY Predstavništvo United Arab Emirates: Jeddah : Tel: +61 (2) 8845 7200 Somfy France Tel: 00381 (0)25 841 510 Somfy Gulf Jebel Ali Free Tel: +966 2 69 83 353 Tel. : +33 (0) 820 374 374 Zone Austria: Singapore:...