SOMFY HOME MOTION J4 RTS Installer's Manual
  1. Manuals
  2. Brands
  3. SOMFY Manuals
  4. Engine
  5. J4 RTS
  6. Installer's manual
SOMFY HOME MOTION J4 RTS Installer's Manual

SOMFY HOME MOTION J4 RTS Installer's Manual

Hide thumbs Also See for HOME MOTION J4 RTS:
Table of Contents

Advertisement

Quick Links

Download this manual
J4 RTS
Notice installateur
Installationsanleitung
Guida d'installazione
Installer Guide

Advertisement

Table of Contents
loading

Related Manuals for SOMFY HOME MOTION J4 RTS

Summary of Contents for SOMFY HOME MOTION J4 RTS

  • Page 1 J4 RTS Notice installateur Installationsanleitung Guida d’installazione Installer Guide...

  • Page 2: Table Of Contents

    2.1. Safety and responsibility - The motor, torque and operating time must be adjusted according to the complete installation. - Only Somfy original accessories should be used (adapters, brackets, connectors, power cable, etc.). personnel. - Correct operation of the installation is only guaranteed if the installation and assembly have been carried out according to best practices, if the electrical supply is adequate and if maintenance is carried out.
  • Page 3 To avoid damaging the product: 2) Never immerse it in liquid! 3) Avoid impacts! 4) Do not drop it! 5) Never drill holes in it! 6) Avoid moving the blind if ice has formed on it. © 2013 Somfy SAS. All rights reserved. 06/2013...
  • Page 4 If the EVB is equipped with a z-shaped slat, it will be necessary to adjust the upper end limit for the motor. In this case, the mushroom is used to ensure the safety of the EVB. Motor tilt The J4 RTS motor has been designed to operate horizontally: 10° maxi © 2013 Somfy SAS. All rights reserved. 06/2013...

  • Page 5: Installation

    Using the clips (5), attach the motor in the head rail (4) above the small acoustic tapes (6a). The shaft can be fitted into the adapter using a headless screw (7). Tightening torque = 2 N.m maximum © 2013 Somfy SAS. All rights reserved. 06/2013...

  • Page 6: 57 X 51 Mm Head Rail, Open Above

    The shaft can be fitted into the adapter using a headless screw (7). Tightening torque = 2 N.m maximum The internal clips cannot be used with J418 motors (J4 motors with a torque of 18 Nm). © 2013 Somfy SAS. All rights reserved. 06/2013...
  • Page 7 The shaft can be fitted into the adapter using a headless screw (7). Tightening torque = 2 N.m maximum For motors with torque greater than 10 Nm The additional clamp must be attached with a new bolt -> tightening torque © 2013 Somfy SAS. All rights reserved. 06/2013...

  • Page 8: 66 Mm Head Rail, Open Below

    Fit the two head rail adaptors (8) on the motor. Insert the motor into the head rail (4). Using the clips (5), attach the motor in the head rail (4). © 2013 Somfy SAS. All rights reserved. 06/2013...

  • Page 9: Wiring

    Do not interlace the supply cable of the J4 RTS plate with another cable. To ensure that the radio signal is transmitted correctly, it is necessary to pull the J4 RTS plate supply cable out of the head rail by at least 30 cm. © 2013 Somfy SAS. All rights reserved. 06/2013...

  • Page 10: Commissioning

    5. COMMISSIONING The guide only describes commissioning using a Telis MOD/VAR type Somfy local control point. For commissioning using any other Somfy local control point, refer to the corresponding guide. 5.1. Identifying setting steps already completed Only one motor should be powered at a time.

  • Page 11: Checking The Motor's Direction Of Rotation

    Otherwise, set the upper end limit position below the mushroom or use mushroom extensions. © 2013 Somfy SAS. All rights reserved. 06/2013...
  • Page 12 Stop the E.V.B. in the desired position (the thumbwheel on the Telis MOD/VAR local control point can be used to set the desired position precisely). Press the Up button (the E.V.B. programming). © 2013 Somfy SAS. All rights reserved. 06/2013...

  • Page 13: Control Point

    E.V.B. has been programmed. Checking the settings 5.7. Check the settings of the upper and lower end limits using the Somfy local control point. 6. OPERATING 6.1. Standard operation 6.1.1. Favourite position (my) Besides the upper and lower positions, an intermediate position known as the «favourite position (my)»...

  • Page 14: Operating With A Somfy Sensor

    (my) position. disappearing (SDP) position. (SDP) position is activated. If the "privacy position" has been activated, the E.V.B. will not change position when the sun is disappearing. © 2013 Somfy SAS. All rights reserved. 06/2013...

  • Page 15: Additional Settings

    Press and hold the "my" and Up buttons for 5 seconds: the E.V.B. button now works only as a "STOP" button. If using a sun sensor, the E.V.B. moves to the lowered position when the sun appears). © 2013 Somfy SAS. All rights reserved. 06/2013...

  • Page 16: Adding/Deleting Somfy Control Points And Sensors

    7.2. Adding/Deleting Somfy RTS control points and sensors 7.2.1. Adding/Deleting an RTS control point Find an RTS control point programmed in the motor. Press the PROG button on the RTS control point (A) until the E.V.B. PROG. PROG. mode. Press the PROG button on the RTS control point (B) E.V.B.

  • Page 17: Sun Disappearing" Position

    Press the "my" button: the E.V.B. starts to move then stops in the favourite (my) position. Press and hold the "my" and Down buttons for 5 seconds: the E.V.B. the sun disappears. © 2013 Somfy SAS. All rights reserved. 06/2013...

  • Page 18: Modifying The Thumbwheel's Direction Of Rotation

    Move the E.V.B. to a position other than the end limits. Press the Up and Down buttons for 5 seconds the E.V.B. and hold the "my" button for 2 seconds: the E.V.B. changed. © 2013 Somfy SAS. All rights reserved. 06/2013...

  • Page 19: Modifying The End Limits

    With a type 3 EVB, stop the EVB before the desired position, and adjust the limit with the thumbwheel of the local control point. Press the Up button (the blind programming). © 2013 Somfy SAS. All rights reserved. 06/2013...

  • Page 20: Tips And Recommendations

    The remote control is not compatible Pair then use a Telis Mod/VAR RTS remote easily control 8.2. Replacing a lost or broken Somfy control point This reset deletes all control points, however, it does not delete the sensors and the favourite position.

  • Page 21: Technical Data

    - 20 °C à + 70 °C Index protection rating IP 54 Maximum number of connected control points Maximum number of connected sensors Safety level Classe I Torque (Nm) Motor length (mm) Acoustic power level © 2013 Somfy SAS. All rights reserved. 06/2013...
  • Page 22 SOMFY Predstavništvo United Arab Emirates: Jeddah : Tel: +61 (2) 8845 7200 Somfy France Tel: 00381 (0)25 841 510 Somfy Gulf Jebel Ali Free Tel: +966 2 69 83 353 Tel. : +33 (0) 820 374 374 Zone Austria: Singapore:...

Table of Contents