Table of Contents
Advertisement
en Descaling
3.
Remove limescale with a cloth soaked in vinegar.
Then wipe with clean water and rub dry with a soft
cloth (including under the door seal).
20 Descaling
To ensure that your appliance continues to operate cor-
rectly, it must be descaled regularly.
How frequently you need to run the descaling pro-
gramme will depend on the water hardness and how
many times you have used the steam function. The ap-
pliance indicates when only another five or fewer
steam-assisted operations are possible. If you do not
carry out the descaling, you can no longer set any op-
eration with steam.
Descaling comprises several steps and takes approx.
70–95 minutes:
¡ Descaling (approx. 55–70 minutes)
¡ First rinse cycle (approx. 9–12 minutes)
¡ Second rinse cycle (approx. 9–12 minutes)
For reasons of hygiene, the descaling programme must
be run in full.
If descaling is interrupted, you can no longer set any
operation. To ensure that the appliance is ready for op-
eration again, carry out two rinse cycles.
20.1 Preparing descaling
ATTENTION!
The length of time for which the descaler is left to work
is based on the recommended, liquid descaler. Other
descalers may damage the appliance.
▶
Only use the liquid descaler recommended by us
for the descaling programme.
If descaling solution comes into contact with the control
panel or other delicate surfaces, it will damage them.
▶
Remove descaling solution immediately with water.
1.
Mix the descaling solution:
200 ml liquid descaler
‒
400 ml water
‒
21 Drying
To prevent residual moisture, dry the cooking compart-
ment following operation.
ATTENTION!
If there is water on the cooking compartment floor
when operating the appliance at temperatures above
120 °C, this will damage the enamel.
▶
Do not use the appliance if there is water on the
cooking compartment floor.
▶
Wipe away any water on the cooking compartment
floor before operation.
21.1 Drying the cooking compartment
You can dry the cooking compartment by hand or use
the drying function.
1.
Allow the appliance to cool down.
2.
Remove dirt from the cooking compartment.
3.
Wipe away the water in the cooking compartment.
28
4.
In order to dry the cooking compartment, leave the
appliance door open in the detent position (approx.
30°) for approx. one hour.
2.
Open the control panel.
3.
Remove the water tank and pour the descaling solu-
tion into it.
4.
Once the descaling solution has been poured into
the water tank, slide the tank back in.
5.
Close the control panel.
20.2 Setting the descaling function
Requirement: → "Preparing descaling", Page 28
1.
Press
.
2.
In the operating mode menu, select "Descaling".
a The duration appears in the display. The duration
cannot be changed.
3.
Press
to start.
a The descaling programme starts and the duration
counts down.
a Once the first part of the descaling programme has
finished, an audible signal sounds. The appliance
prompts you to rinse twice.
4.
To rinse the appliance, for each rinse cycle:
Open the control panel and remove the water
‒
tank.
Thoroughly rinse the water tank and fill it with
‒
fresh water.
Slide in the water tank and close the control
‒
panel.
Use
to start rinsing.
‒
a A signal sounds when each rinse cycle has ended.
5.
Once the second rinsing cycle is complete:
Empty and dry the water tank.
‒
→ "Emptying the water tank", Page 18
Press
to switch the appliance off
‒
a Descaling is complete and the appliance is ready
for use.
4.
Dry the cooking compartment.
Leave the appliance door open for one hour to
‒
dry the cooking compartment by hand.
In order to use the drying function, set the drying
‒
function.
→ "Setting the drying process", Page 28
Setting the drying process
1.
Allow the appliance to cool down.
2.
Remove coarse dirt from the cooking compartment
and wipe away moisture from the cooking compart-
ment floor.
3.
Press
.
4.
In the operating mode menu, press the drying oper-
ating mode.
The duration is set to 10:00 min. and cannot be
changed.
Advertisement
Table of Contents
