Hager EG071 - 1 Channel Time Switch Manual and Tutorial Video

Function

The EG071 is a programmable time switch for the automatic control of electrical loads.
It is fully programmable with a maximum of 20 program steps. Each program step can be applied to one or several days, maximising the use of each memory location.
The display will flash in case of power failure to the unit.
The front cover is sealable preventing unauthorised access after completion of programming.

Presentation

Display

1. time.
2. circuit status (ON or OFF)
3. Day of the week (1 = Monday, 2 = Tuesday.. 7 = Sunday)

Buttons

4. "on/off" chooses whether the circuit is ON or OFF.
5. "Prog" to set the program and scroll program steps.
6. "reset"
7. "+" and "-": changes settings.

Time and day setting

Press key "+" or "-".
A continuous pressure on this key will scroll up or down minutes, hours and then days.

Programming

1. To start programming, press key "Prog", the first program step flashes.
   
2. Set the switching time with key "+" or "-"
3. Use the "on/off" button to choose between circuit ON and circuit OFF.
   ON = contact between terminals 2 and 3.
   OFF = contact between terminals 1 and 2.
4. Enter the settings by pressing "Prog". You must now choose the days of the week that the settings apply to.
   
5. With key "+" and "-", display one after the other each day of the week and select with key "on/off" if the program applies to this day or not. Days to which the switching is to be applied must be visible at the bottom of the display e.g. 1 2 3 4 5 visible, means switching will be applied Monday to Friday.
6. Press "Prog" to enter this program step.
   If no buttons are pressed within 2 min., the device switches back to automatic mode without recording your settings.
7. Program additional time settings by repeating steps 2 to 6 above (20 max.)
   To delete a program step, modify switching time with keys "+" and "-", until display --:-- (between 23:59 and 00:00).
8. To record your settings and return to automatic mode press "Prog" for more than 2 seconds.
   

To turn the circuit ON or OFF

1. press the "on/off" button. The display flashes.
   
2. use the "on/off", button to turn the circuit ON or OFF.

To switch back in automatic mode, press "on/off" for more than 2 seconds.

To check your settings

In automatic mode:
Press "Prog" repeatedly to display the day, the time and the circuit status (ON or OFF).
To switch back to automatic mode, press "Prog" for more than 2 sec.

To reset the time switch

Press the "reset" button, the program will be cancelled.

Technical specifications

Electrical characteristics

• supply voltage: 230V +10%/-15% 50/60Hz
  240V~ +/-6% 50/60Hz
• power consumption = 1 VA
• output: 1 changeover contact
  µ 16A - 230V AC1
  µ 3A - 230V cos ϕ = 0.6
• protection degree: IP20
• insulation class: II
• maximum operating height: 2000m
• rated impulse voltage: 4 kV
• upstream circuit breaker: 16 A
• voltage and current declared for the needs of EMC emissions tests: 230V~ / 0,5 A

Independent panel-mounted (DIN rail) control device

Functional characteristics

• accuracy: ±1min/day at 20°C
• operating reserve: lithium battery total of three years
• action type: 1B
• pollution category: 2
• software structure: class A

Environment

• operating temperature; -10 to +50°C
• storage temperature: -10 to +60°C

Connection tunnel terminals

• flexible: 0.5 to 2.5 mm²
• rigid: 0.5 to 4 mm²

Size: (17.5 mm)

Electrical connections

Warranty

NOT APPLICABLE FOR AUSTRALIA

A warranty period of 24 months is offered on hager products, from date of manufacture, relating to any material of manufacturing defect. If any product is found to be defective it must be returned via the installer and supplier (wholesaler).

This device must be installed only by a qualified electrician according to the installation standards in force in the country.

Correct Disposal of This product (Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems).

This marking shown on the product or its literature indicates that it should not be disposed with other household wasted at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes of disposal.

Usable in all Europe and in Switzerland

Hager Controls S.A.S., 3 rue Saint-Nicolas, B P. 10140, 6 703 SAVERNE CEDEX, France - www.hager.com