hager EG 470 User Instruction

A
A
B
O F F
B
A u to O N
O F F
C
P ro g
O N
O F F C
D
O N
O F F
O N
D
e t
re s
7 o ff
6 a u to
5 o n
4
r
e n te
3
2
1
+
–
ff
o n /o
r
c le a
EG 470
Working principle :
The EG 470 is a time switch for the auto-
matic control of electrical loads.
It is fully programmable with a maximum
of 84 program steps to be divided bet-
ween the four channels. Each program
step can be applied to one or several
days, maximising the use of each memo-
ry location.
An input lets you simultaneously force
the 4 channels to OFF.
The front cover is sealable preventing
unauthorised access after completion of
programming.
Warning : at the beginning of use, please
reset the device in order to clear the
memory before programming.
This is achieved by using a pen to push
the reset button.
Presentation :
2 3
Prog Auto
5
ON OFF A
1
ON OFF B
ON OFF
C
4
ON OFF
D
7
1 2 3 4 5 6 7
reset
clear on/off – + enter on auto off
8 9 10 11 12 13
Display :
➀
time
➁
circuit status of channels A, B, C and D
(ON or OFF)
➂
Indication of manual override on
channels A, B, C and D.
➃
day of the week
(1 = Monday, 2 = Tuesday ....)
➄
Indicator of operating mode :
time setting
prog programming mode
for channels A, B, C and D
auto running mode
timed override.
Buttons :
➅
Manual selector to override channels
A B, C and D.
➆
"1" to "7" selection of the days
➇
"clear" : to delete a program step.
➈
"on/off": chooses whether the circuit
is on or off
➉
"+" and "-" : changes settings
: to select the operating mode
11
(time setting, programming, running
mode or override)
12 "enter": to confirm
13 "reset"
User instruction
4 channels time switch -
weekly cycle
Time and day setting :
Prog Auto
1 2 3 4 5
– +
clear on/off
1. Press the key repeatedly to place the cursor
below
2. Select with key "1" to "7" , the actual day
(1 = Monday, 2 = Tuesday .)
3. Input time with buttons "+" and "-".
Programming channel A :
Prog Auto
A
B
C
1 2 3 4 5
D
6
clear on/off – +
1. Press the key repeatedly to place the cursor
below "prog" for channel A.
2. Select with keys "1" to "7" the day(s) assigned to
this program step. An arrow appears above each
day selected.
3. Input switching time with buttons "+" and "-".
4. Input the type of switching with button "on/off"
(for the first action ON is automatically proposed).
5. Enter this program step with button "enter".
Program additional time settings by repeating steps
2 to 5..
Programming channels B, C and D :
Press key to place the cursor below "prog" for
channels B, C or D.
Same way of programming as channel A.
Running Auto mode
The switch to automatic mode is made automati-
cally if no key is pressed for 2 minutes.
You can also select the "auto" mode by pressing
the key to place the cursor below "auto".
This mode is the current displaying mode.
Display of the time, the day and the state of the
four channels.
This mode does not allow any modification, except
the winter / summer time change.
Press key "+" or "-" and confirm with "enter".
GB
A
A
B
C
D
B
C
6 7
reset
D
enter on auto off
A
ON
A
B
C
D
B
C
6 7
reset
D
enter on auto off
To check your program on channels A,
B, C or D :
1. Press the key repeatedly to place the
cursor below "prog" for channel A, B, C or D.
2. Press the key "enter" repeatedly to display
the different program steps (switching
time, days of the week and state of the
channel ON or OFF).
To modify or delete a program
step on channels A, B, C or D :
Prog Auto
ON A
B
C
D
1 2 3 4 5 6 7
reset
clear on/off enter
– +
1. Press the key repeatedly to place the
cursor below "prog" for channel A, B, C or D.
2. Press the key "enter" repeatedly to select
the program step to modify or to delete.
3. Modify :
- switching time with keys "+" or "-"
- days assigned with keys "1" to "7".
- state of the channel with key "on/off".
To delete a program step, press "clear".
4. press "enter" to confirm.
To override the output :
Permanent override :
The 3 position selector (on - auto - off) for channels
A, B, C or D allows in automatic mode the output to
be overriden ON or OFF.
Prog Auto
A
ON
OFF B
ON
C
ON
D
1 2 3 4 5 6 7
reset
clear on/off enter
– +
1. Move the 3 position selector for channels
A, B, C or D to "ON" or "OFF"
2. A cursor on the display (in front of
channels A, B, C or D) indicates the
permanent override.
To switch back to automatic mode, move the
selector to "auto".
A
B
C
D
on auto off
A
B
C
D
on auto off