Advertisement

Quick Links

KBL 6900 / MAX10
Operating Instructions

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 6900 MAX10 and is the answer not in the manual?

Questions and answers

Summary of Contents for KBL 6900 MAX10

  • Page 1 KBL 6900 / MAX10 Operating Instructions...
  • Page 2 Copyright and Trademark © Copyright 2007 KBL AG This documentation covers only products manufactured by KBL This documentation must not be duplicated, photocopied, translated or stored on any electronic medium or in a machine- readable form, neither in whole or in part, without prior written consent by KBL AG.
  • Page 3: Table Of Contents

    Service level I ........................45 Service level II ........................53 Refilling / Changing Aroma and aquaCool................56 Colour codes for the pipes....................57 Error message ........................58 Tanning instructions ......................... 59 General tanning instructions ....................59 Operation and Service KBL 6900 / MAX10...
  • Page 4: General Safety - Exposure Schedule - Service

    Section 5.8 Please also keep to the service cycles given in the service plan (Section 2). Do not use any cleaning agents other than the ones approved Cleaning by KBL AG. Section 5.1 Operation and Service KBL 6900 / MAX10...
  • Page 5 1246 Central Park Dr. St. # 1 62269 O’Fallon, IL phone: 618-624-6000 NOTE: All repairs and replacement components including, but not limited to protective eyewear, lamps, timers and acrylic must be in compliance with CFR 21 1040.20. Operation and Service KBL 6900 / MAX10...
  • Page 6 (4) weeks of exposure. WARNING: As the device is intended to be used by only one person at a time, only one (1) pair of protective eyewear is provided with each KBL 6900. Use protective eyewear whenever equipment is energized. Read the instruction booklet before using.
  • Page 7: Service Plan

    For CPI-apparatuses (with burners) in Eco-mode or for CPI- apparatuses (without burners) in Power-mode: • Change tubes • Reset counters (8.2.2) • Reset counter of service hours For CPI-apparatuses (without burners) in Eco-mode with KBL CPI-tubes in Power-mode: 1000 • Change tubes • Reset counters (8.2.2) •...
  • Page 8: Equipment

    Air conditioning Electronic ballasts Music, MP3-player With a 256 MB memory for music Music, external signal Waste air tube Ø ~11.81”, ~118.11” Central exhaust air element Warm air recirculation legTanner S Default O Option Operation and Service KBL 6900 / MAX10...
  • Page 9: Operation During The Tanning Session

    Main display „waiting position“. When the coin-controlled signal appears, the functions are displayed and the sunbed can be operated by touching the corresponding keys. Any input will be confirmed by a beep tone. Operation and Service KBL 6900 / MAX10...
  • Page 10: Functions

    When adjusting the volume, the value set between 0 ... 99 % will be displayed in this field for a short time. When adjusting the fan speed, the value set between 20 ... 99 % will be displayed in this field for a short time. Operation and Service KBL 6900 / MAX10...
  • Page 11 „-„ keys. The volume will be displayed in the numerical field as a value between 0 – 99 %. Press the corresponding sensor key again and again until you have reached the desired volume. Operation and Service KBL 6900 / MAX10...
  • Page 12 When the system has been switched off, there will be a time lag before you can switch it on again due to the necessary cooling of the burners. Operation and Service KBL 6900 / MAX10...
  • Page 13 Tip: The music of the MP3-unit can only be controlled by one audio source, i.e. either by the chip of the MP3-player or by an external music source. Operation and Service KBL 6900 / MAX10...
  • Page 14 You can only switch on one colour, but you can switch them all off (see Service level). 48 high-performance diodes for each colour (Red - Green - Blue) produce the mood desired: relaxing blue, stimulating blue and calming green. Operation and Service KBL 6900 / MAX10...
  • Page 15 G off switchable via the menu. The other colour stimulation „activeColor“ (R - G - B) is without effect and is no longer offered for KBL 6900. It is only present for compatibility. Operation and Service KBL 6900 / MAX10...
  • Page 16 “1” and switched off by the „ - “ key below „0“. The display flashes a signal when the function is not activated. KBL can offer 2 aroma fragrances: „Sunrise“ and „Daydream“. The apparatus only has one fragrance which can changed very easily, however.
  • Page 17: Tips For The Studio Operator

    But before doing so, service people should repair the defect. air) Possible reasons of this message can be: • the temperature in the apparatus is too high or • the exhaust vent system is defective For more information see 8.6 Operation and Service KBL 6900 / MAX10...
  • Page 18: Maintenance Of The Sun Bed

    For a harmless cleaning of the acrylic panes use the special Acrylic panes cleaning and disinfectant fluid „ megaClean “ (to be obtained from KBL) which has to be diluted in water at a ratio of 1:13. Clean only with a damp (not wet) washleather and a plexiglass Chromed parts cleaner (antistatic).
  • Page 19: Dismantling The Acrylic Panes

    You can also use it to clean the shoulder tanner. You can use megaClean as a detergent (spray the cloth with it). Operation and Service KBL 6900 / MAX10...
  • Page 20 Proceed in the same way with the shoulder tanner. Clean the upper surface of the base pane and fasten it with the two screws. Illustr. 5-4 Pan-head screw Illustr. 5-5 Suspension of the base pane Illustr. 5-6 Duct pane Operation and Service KBL 6900 / MAX10...
  • Page 21: Filter Panes

    After cleaning the pane, mount it again in reverse order. Illustr. 5-7 Remove filter pane cover Illustr. 5-8 Remove pane from the clamping springs The filters are marked with Mark „KBL 3020 0191“ Operation and Service KBL 6900 / MAX10...
  • Page 22: Tubes, Facial And Shoulder Tanners

    Shoulder Burner tanner mode tanner mode tanner Starters Power Power Super P. 500-600 500-600 1200 1000 1200 1000 hrs. hrs. hrs. hrs. hrs. hrs. hrs. hrs. Carry out a reset! Operation and Service KBL 6900 / MAX10...
  • Page 23 (foot area). inductive units Illustr. 5-9 Starter of tube 21 Illustr. 5-10 Left socket for tube 21 Illustr. 5-11 Back of lateral reflector with starter of tube 21 Operation and Service KBL 6900 / MAX10...
  • Page 24: Replacing The Burner Of The Facial Tanner

    Insert the burners in a straight position into their sockets. After being inserted into the socket, the little metal shackle in the centre of the reflector should face the reflector. Operation and Service KBL 6900 / MAX10...
  • Page 25: Replacing The Burner Of The Shoulder Tanner

    Position the reflector correctly under the Illustr. 5-6-8 chrome covering. To do so, press the reflector slightly to align it. Attach the outer covering vertically and tighten the screw. Operation and Service KBL 6900 / MAX10...
  • Page 26 Illustr. 5-6-6: Insert the new burner take off the burner including socket and ensure a snug fit Flat projection Illustr. 5-6-7: Insert the reflector Illustr. 5-6-8: Reflector correctly posi- tioned under the chrome cover Operation and Service KBL 6900 / MAX10...
  • Page 27: Unit Lighting

    (or to the left). Now you can replace the tube. Close the base pane. Illustr. 5-14 Unit lighting in the lower front section and the starter for this tube on the left side. Operation and Service KBL 6900 / MAX10...
  • Page 28 Make sure hat the reflector plate does not damage the tanning tubes. Release the tube and lift it up and sidewards, so you can take it out through the opening, then. Operation and Service KBL 6900 / MAX10...
  • Page 29: Filter Mats

    Filter mat in the base section. Open the bed pane and remove the fluorescent base section tube. Now you have free access to the filter mat. Illustr. 5-17 Filter mat in the base section Operation and Service KBL 6900 / MAX10...
  • Page 30: Canopy Drive

    XXL-unit remove the cover plates. Tighten both springs in a balanced way. Check the canopy drive: the canopy remains firm in any position. Close the lateral pane. Illustr. 5-18 Left tension screw Illustr. 5-19 Right tension screw Operation and Service KBL 6900 / MAX10...
  • Page 31: Cooling System And Exhaust Air

    (tubes). The exhaust air is then blown off through the exhaust flue (green). Illustr. 5-20 Body cooling (blue) and unit Illustr. 5-21 Exhaust fan (mounting cooling (green), filter mats (orange) and picture) warmed air (red) Operation and Service KBL 6900 / MAX10...
  • Page 32 (three nozzles). Air nozzles Filter mat Air- conditioning unit with fan and air hose Illustr. 5-24 Cooling principle of base section Operation and Service KBL 6900 / MAX10...
  • Page 33: Air-Conditioning Unit

    Open the front cover and vacuum-clean the heat exchangers, if necessary. Check the connection hose each time the tubes are replaced. Defective hoses must be replaced. Operation and Service KBL 6900 / MAX10...
  • Page 34: Condensate Pump

    - the aquaCool function must be switched off suddenly and the canister must be replaced by a new one. More about replacement see Section 8.4 . aroma About replacement see Section 8.4 . Operation and Service KBL 6900 / MAX10...
  • Page 35: Music System With Mp3-Player

    (see illustration on the following page). Illustr. 5-26 Installation below the base Illustr. 5-27 MP3 player with music card pane Illustr. 5-28 Construction elements Illustr. 5-29 MP3 for megaVoice Operation and Service KBL 6900 / MAX10...
  • Page 36: Replacing The Aquacool Nozzles

    After 1000 hours of operation, the aquaCool nozzles have to be replaced in order to ensure that aquaCool stays fully operative and efficient. The installation instructions will be enclosed in your spare parts consignment. Operation and Service KBL 6900 / MAX10...
  • Page 37: Technical Data

    ~92.91” x ~53.15” x ~55.12” when closed ~92.91” x ~53.15” x ~70.87” when opened Central exhaust air duct Diameter ~11.81” Height (top edge) ~62.99” Exhaust air hose Ø ~11.81” Weight (with air- ~1477.1 lbs conditioning unit) Operation and Service KBL 6900 / MAX10...
  • Page 38: Views

    12590 ning unit w/o air-conditio- 11330 ning unit 3-phase: 3x 50 A (for Canada with ground fault circuit interrupter) Fuses 2-phase: 2x 70 A (for Canada with ground fault circuit interrupter) Operation and Service KBL 6900 / MAX10...
  • Page 39: Wiring Diagram

    K1.3 X0.N3 K2.3 K2.5 change connections K2.5 K1.5 K1.3 L3(T) (K2.5) - from[X0.L3D]to[X0.L2C] X0.N6 K1.5 X0.N1 (X0.N1) - from[X0.L1C]to[X0.L3D] L2(S) X0.N6 X0.N3 (K1.5) - from[X0.L3D]to[X0.L2C] (X0.N3) - from[X0.L2C]to[X0.L3D] set jumper X0.L3 from[X0.L1]to[X0.L2] X0.L3 Operation and Service KBL 6900 / MAX10...
  • Page 40: Megavoice Without Music Option

    (connected in parallel, equal-phased). Music amplifier C Audio- switch megaVoice 3220 2885 00 3220 3230 20 3220 3222 95 E8: 6 5 ... 2 1 MP3 Musik 3220 3222 90 Audio switch MP3 Music MP3 megaVoice Operation and Service KBL 6900 / MAX10...
  • Page 41: External Music Signal Without Channel Selection

    9100017000, and the music signal is connected to the clamps “IN”. Transformer 9100 0170 00 C Audio- Music amplifier switch 3220 2885 00 megaVoice 3220 3230 20 E8: 6 5 ... 2 1 3220 3222 95 Transformer Music signal Operation and Service KBL 6900 / MAX10...
  • Page 42: External Music Signal With Channel Selection

    Audio switch. (see 7.4) The following diagram shows the wiring of the channel selection on the audio equipment’s side. Wiring on the audio system of the studio Wiring on the audio system of the studio Operation and Service KBL 6900 / MAX10...
  • Page 43: External Timer

    Connect the RJ22 cable to the board and guide it together with the power or RCA jack cable through the feedthrough in the back. Illustr. 7-8-2: Board attached Illustr. 7-8-1: Position of spacer supports Operation and Service KBL 6900 / MAX10...
  • Page 44: Service

    Key 5 to move forward in the menu Key 0 to move backwards in the menu Stop key to leave service level or menu Start key to select a menu item or to save the value displayed Operation and Service KBL 6900 / MAX10...
  • Page 45: Service Level I

    Booth ON/OFF B. Inter 00/h Gate ON/OFF B.Timer AR. Cont 99% Aqua ON/OFF AQ. Time Color R G B Cycle Audio Extern Extern Volume 84% (±2%) ON / OFF Nonstop Preselection W P S Operation and Service KBL 6900 / MAX10...
  • Page 46 Selection With the START key you open the sub menus. With the STOP key you go back one level higher. If you have changed a value and you will safe it press START. Operation and Service KBL 6900 / MAX10...
  • Page 47 1. The hours are set using keys 2 – 4 and the minutes with the help of the keys 3 – 8 Weekday: Monday to Sunday Selection Confirm..Time A/BON and A/BOF Hours / Min Safe Operation and Service KBL 6900 / MAX10...
  • Page 48 The day of the week appears automatically PIN II opens service level II. PiN II Enter PIN II and the menu on „service level II“ opens. Ask the KBL-Service for PIN II. This menu has four sub-menus: : • AROMA •...
  • Page 49 AQ.TIME: The spraying cycle is set in the menu CYCLE and the spraying duration in this menu AQ.TIME between 2 ... 6 seconds. The details are set by pressing the „+“ and „-“ keys above or under the time display. Operation and Service KBL 6900 / MAX10...
  • Page 50 The duration of the breaks of aroma and aqua can be set between 1... 5 minutes. The details are set by pressing the „+“- and „-“ keys above or below the time. Adjust Confirm. + / - Operation and Service KBL 6900 / MAX10...
  • Page 51 / off Conrm. + / - Adjust in 2-%- + / - Steps Adjust in 2-%- + / - Steps on / off+ / - Select Conrm. on / off+ / - Operation and Service KBL 6900 / MAX10...
  • Page 52 Pop and for „next external music channel“ with Studio (see also service level II for the configuration the external chan- nels in menu „C M A B“ ). Use +“ key for forward and „-“ key for backward. Operation and Service KBL 6900 / MAX10...
  • Page 53: Service Level Ii

    The setting can be changed by pressing the “+” or “-“ key above or below the symbol. If the two dots behind the letter are at the bottom, the respective function is inactivated. no channel selection possible, facial tanner can be operated Operation and Service KBL 6900 / MAX10...
  • Page 54 Attention! Always carry out a reset after each tube replacement Enter the hours change safe Here you can store the time stamps of the rst and last download Time stamps of the software. Selection First Download Last Download Operation and Service KBL 6900 / MAX10...
  • Page 55 This is analogue to the display after the rst start. The version depends on the sunbed: without easyCare (here 5.3) or with easycare (here 1.8). Selection Sub-type of the sun bed UV-type Sun bed Operation and Service KBL 6900 / MAX10...
  • Page 56: Refilling / Changing Aroma And Aquacool

    Screw the lid on again. Keep clean the end of the tubes when changing the tank (use a plastic bag). Only use the specic water by KBL „aquacool“. Otherwise the nozzles may clog up which might produce infections. Put the constructional elements back into their original place in the sunbed.
  • Page 57: Colour Codes For The Pipes

    Yellow aroma Abb. 8-2 Compressor Abb. 8-3 aquaCool Abb. 8-4 aroma Abb. 8-5 Canopy underside Abb. 8-6 Canopy upper side Abb. 8-7 Ionizor and aroma pipes Abb. 8-8 Pipes at the nozzles Operation and Service KBL 6900 / MAX10...
  • Page 58: Error Message

    — formating or wrong inserted, — Plug at MP3 iInterface or at I²C Audio switch is inserted uncorrect. Conguration error: I²C-Relay board (8) an I²C Relais board (2) at E05BUS:REL the same time connected. Operation and Service KBL 6900 / MAX10...
  • Page 59: Tanning Instructions

    • people who get sunburn without tanning when exposing themselves to the sun • people suffering from sunburn • people who suffer or have suffered from skin cancer or who are predisposed towards it Operation and Service KBL 6900 / MAX10...
  • Page 60 KBL AG Ringstraße 24-26 · 56307 Dernbach · Germany fon +49 (0) 26 89.94 26-0 · fax +49 (0) 26 89.94 26-66...

Table of Contents