Graco LineLazer III 200HS Operation
  1. Manuals
  2. Brands
  3. Graco Manuals
  4. Industrial Equipment
  5. LineLazer III 200HS
  6. Operation
Graco LineLazer III 200HS Operation

Graco LineLazer III 200HS Operation

Hide thumbs Also See for LineLazer III 200HS:
Table of Contents

Advertisement

Quick Links

Download this manual
Operation
LineLazer III 200
Read all Warnings and Instructions
3300 psi (227 bar, 22.7 MPa) Maximum Working Pressure
✓
234240
234241
✓
234242
234243
✓
234244
234245
Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441
Copyright 2003, Graco Inc. is registered to I.S. EN ISO 9001
✓
✓
✓
✓
✓
✓
✓
✓
✓
HS
✓
✓
309892A
ti3280a

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LineLazer III 200HS and is the answer not in the manual?

Questions and answers

Related Manuals for Graco LineLazer III 200HS

Summary of Contents for Graco LineLazer III 200HS

  • Page 1 ✓ ✓ 234240 ✓ ✓ 234241 ✓ ✓ 234242 ✓ ✓ 234243 ✓ ✓ ✓ 234244 ✓ ✓ ✓ 234245 ti3280a Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441 Copyright 2003, Graco Inc. is registered to I.S. EN ISO 9001...
  • Page 2 Warning WARNING MISE EN GARDE FIRE AND EXPLOSION HAZARD DANGER D’INCENDIE ET D’EXPLOSION Solvent and paint fumes can ignite or explode. Les gaz de solvent et de peinture peuvent s’enflammer ou exploser. To help prevent a fire and explosion: • Use only in an extremely well ventilated area.

  • Page 3: Tip Selection

    Tip Selection Tip Selection (cm) (cm) (cm) (cm) ✔ 221203* 2 (5) ✔ LL5213* 2 (5) LL5215* 4 (10) ✔ LL5217 4 (10) ✔ ✔ LL5219 4 (10) ✔ LL5315 4 (10) ✔ LL5317 4 (10) ✔ LL5319 4 (10) ✔...
  • Page 4 ti3671a Label No. 15A245, English Display Main ON/OFF switch Spray gun control Prime/Spray valve Filter Trigger lock Engine/Controls Drain and siphon tubes Pump valve Pressure control Turn control 309892A...
  • Page 5 Setup Setup Approximate Fill Level ti3308a ti3307a ti3309a ti3306a Ground sprayer with ground- Fill throat packing nut with Check engine oil level. Add Fill fuel tank. ing clamp during Setup and TSL to decrease packing SAE 10W-30, if necessary. Cleanup. wear.
  • Page 6 Safe Range (cold) ti3422a ti3430a Check hydraulic oil level. Set pump valve OFF. Install new strainer. Add Graco hydraulic oil, Grade 46, 169236 (5 gal- lon/18.9 liter) or 207428 (1 gallon/3.8 liter). Hydraulic tank capacity is 1 gallon(3.8 liter). 309892A...
  • Page 7 Setup ti3310a ti3296a PAINT ti3441a FLUSH Turn prime valve down. Turn Place siphon tube set in grounded metal pail partially filled with flushing fluid. Attach ground wire to pail pressure control counter- and to true earth ground. Do 1. - 5. of Startup to flush out storage oil shipped in sprayer. Use water to clockwise to lowest pres- flush water-base paint and mineral spirits to flush oil-base paint and storage oil.
  • Page 8 Startup Startup ti3313a ti3312a ti3314a ti3315a Start engine. Move fuel valve to open Move choke to closed Set throttle to fast Set engine switch ON 309892A...
  • Page 9 Startup ti3317a ti3316a ti3302a ti3318a Pull starter cord After engine starts, move Set throttle to desired set- Digital display is functional after engine starts. choke to open ting 309892A...
  • Page 10 Startup ti3294a 3304a ti3442a ti3442a ti3421a ti3322a Set pump valve ON. - Increase pressure enough to Take spray gun trigger safety Hold gun against grounded Hydraulic motor is now start hydraulic motor stroking metal flushing pail. Trigger active - and allow fluid to circulate for gun and increase fluid pres- 15 seconds;...
  • Page 11 Startup ti3325a ti3324a seat ti3327a PAINT ti3316a ti3322a ti3326a OneSeal SwitchTip and Guard Assembly Place siphon tube in paint Trigger gun again into flush- Engage trigger safety. Insert Screw assembly onto gun. pail. ing fluid pail until paint SwitchTip. Insert seat and Hand tighten.

  • Page 12: Gun Placement

    Gun Placement Gun Placement ti3331a ti3332a ti3328a ti3329a ti3330a ti3342a Install Gun Position Gun Select Gun Insert gun into gun holder. Position gun up/down, for- Connect gun cables to left or a One gun: Disconnect one gun selector plate from trigger. Tighten clamp.
  • Page 13 Gun Placement TI3710a English One line One line up to 24 in. (610 cm) wide. Two lines One line or two lines to spray around obstacles One gun curb Two gun curb Two lines or one line up to 24 in. (610 cm) wide. 309892A...

  • Page 14: Trigger Sensor Adjustment

    Gun Placement ti3691a ti3355a ti3347a ti3343a Trigger Sensor Adjustment Clearing Tip Clogs Adjust screw in handle to syn- Release trigger, put trigger Put trigger safety ON, return safety ON. Rotate SwitchTip. SwitchTip to original posi- chronize spray icon with fluid Take trigger safety OFF and tion, take trigger safety OFF spray.

  • Page 15: Digital Tracking System (Dts)

    Digital Tracking System (DTS) Digital Tracking System (DTS) ti3364a ti3399a ti3369a ti3356a ti3389a ti3400a ti3378a Operation - Main Menu Short press moves to next dis- Start engine, page 8. Short press DTS button to Short press DTS button to play. Sprayer Model displays briefly.
  • Page 16 Digital Tracking System (DTS) ti3401a ti3405a ti3403a TI3407a ti3402a ti3408a ti3406a ti3404a Short press DTS button to Short press DTS button to Short press DTS button to Press and hold DTS button move to Job Distance (ft or m). move to Job Material move to Line Width (LW) to change LW.
  • Page 17 Digital Tracking System (DTS) ti3409a TI3411a TI3359A TI3363A ti3410a TI3357A TI3361A TI3366A Short press DTS button to Short press DTS button to Press and hold DTS button move to Job Film Build. move to job RESET display. to reset job distance, job short press DTS button to Note: Displays the average wet material and film build values...
  • Page 18 Digital Tracking System (DTS) TI3368A TI3374A TI3362A TI3376A TI3379A TI3372A DTS Secondary Menu Start engine, page 7. Simultaneously press DTS Measure Mode display appears To use Measure Mode, press Pressure display appears button and set ON/OFF and hold DTS button until switch ON.
  • Page 19 Digital Tracking System (DTS) ti3288a TI3384A TI3381A TI3386A Short press DTS again to Short press DTS again to Press and hold DTS button Set ON/OFF switch OFF to start measuring. stop measuring. to reset to zero. exit Measure mode. ON appears on left side of Note: Repeated short presses of display.
  • Page 20 Digital Tracking System (DTS) TI3387A TI3391A TI3393A TI3394A Short press DTS button to Short press DTS button to Short press DTS button to Short press DTS button to move from MEAS display to move to Total Material move to SPRAY (distance). move to TOTAL (distance).
  • Page 21 Digital Tracking System (DTS) TI3398A TI3396A TI3397A TI3395A Short press DTS button to Short press DTS button to Press DTS button to move to Short press to move to dis- move to Engine Hour dis- move to live Engine RPM stored error code.
  • Page 22 Digital Tracking System (DTS) Roll 25ft or 10 m ti3419a TI3360A ti3418a TI3358A To calibrate distance meter, Move LineLazer exactly 25 ft Press DTS again to return to Short press DTS button to accurately measure out 25 ft or 10 m. Do not back up. CAL screen.

  • Page 23: Change Display Units

    Digital Tracking System (DTS) ti3288a TI3367A TI3367A TI3365A TI3362A Change Display Units Turn ON/OFF switch OFF at Pressure: Volume: Distance: any time to exit Secondary Press and hold (8 seconds) Press and hold (8 seconds) Press and hold (8 seconds) Menu and return to pressure DTS button to change pressure DTS button to change volume...

  • Page 24: Pressure Relief

    Cleanup Cleanup ti3296a ti3305a ti3288a PAINT ti3441a ti3422a ti3306a Pressure Relief Pressure Relief Pressure Relief Ground sprayer with ground- Set pump valve OFF. Turn pressure to lowest set- Turn prime valve down. ing clamp. Turn ON/OFF switch OFF. ting. Trigger gun to relieve pres- sure 309892A...
  • Page 25 Cleanup ti3310a PAINT TI3371A TI3375A FLUSH FLUSH ti3690a Remove guard and Unscrew bowl, remove filter. Clean filter, guard and Remove siphon tube set SwitchTip. Assemble without filter. SwitchTip in flushing fluid. from paint and place in flush- Clean filter. ing fluid. Use water for water base paint and mineral spir- its for oil base paint.
  • Page 26 Cleanup ti3294a ti3287a ti3421a ti3417a ti3442a TI3377A PAINT FLUSH Turn ON/OFF switch ON and Turn prime valve horizontal. Hold gun against paint pail. Move gun to flushing pail, start engine. Set pump valve Take trigger safety OFF. hold gun against pail, trigger Turn pressure control up gun to throughly flush sys- until motor begins to drive...
  • Page 27 Cleanup PAINT ti3296a FLUSH TI3383A 20 SEC TI3380A ti3288a Pump Armor TI3385A ti3441a ti2895a Turn prime valve down and Raise siphon tube above Caution: If flushing with water, Make sure plastic center allow flushing fluid to circu- flushing fluid and run flush again with mineral spirits, tube is tightened securely.
  • Page 28 Cleanup TI3388A TI3390A FLUSH Wipe sprayer, hose and Clean tip, guard and gasket gun with a rag soaked in wth a soft bristle brush to water or mineral spirits. prevent part failure due to dried materials. Assemble parts and attach loosely onto gun.
  • Page 29 Graco distributor to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.
  • Page 30 Warranty / Garantie / Garantía / Garanzia / Garantia TO PLACE AN ORDER, contact your Graco distributor, or call 1-800-690-2894 to identify the nearest distributor. All written and visual data contained in this document reflects the latest product information available at the time of publication.

Table of Contents