Storage; Electrical Connection - Scheppach DP16VLS Instruction Manual

Adjusting the spindle retaining spring (Fig. 9)
It may be necessary for the spindle retaining spring to
be adjusted because of changed tension, making the
spindle return too quickly or too slowly.
1. To provide more space, lower the table.
2. Work on the left side of the drill.
3. Put a screwdriver in the front lower notch (L), keep-
ing it in place.
4. Remove the outer locknut (O) with a flat spanner
(SW16).
5. Leaving the screwdriver in the notch, loosen the
inner locknut (N) until the cut-out is released from
the boss (P).
WARNING! Spring is under tension!
6. Using the screwdriver, carefully turn the spring cap
(M) anti-clockwise until you can press the notch
into the boss (P).
7. Lower the spindle to the lowest position and hold
the spring cap (M) in place. When the spindle
moves up and down as desired, retighten the inner
locknut (N).
8. If it is too loose, repeat steps 3-5. If it is too tight,
repeat in reverse order.
9. Using a flat spanner, tighten the outer locknut (O)
against the inner locknut (N).
NOTE: Do not over-tighten and do not restrict the
movement of the spindle!
Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the following
parts are therefore also required for use as consum-
ables.
Wear parts*: carbon brushes; V-belts, batteries, bits
* Not necessarily included in the scope of delivery!
Spare parts and accessories can be obtained from our
service centre. To do this, scan the QR code on the
cover page.

12. Storage

Store the device and its accessories in a dark, dry and
frost-proof place that is inaccessible to children. The
optimum storage temperature is between 5 and 30˚C.
Store the electrical tool in its original packaging.
Cover the electrical tool in order to protect it from dust
and moisture.
Store the operating manual with the electrical tool.

13. Electrical connection

The electrical motor installed is connected and
ready for operation. The connection complies with
the applicable VDE and DIN provisions. The cus-
tomer's mains connection as well as the extension
cable used must also comply with these regula-
tions.
Important information
In the event of an overloading the motor will switch it-
self off. After a cool-down period (time varies) the mo-
tor can be switched back on again.
Damaged electrical connection cable
The insulation on electrical connection cables is often
damaged.
This may have the following causes:
• Passage points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been improp-
erly fastened or routed.
• Places where the connection cables have been cut
due to being driven over.
• Insulation damage due to being ripped out of the wall
outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not be
used and are life-threatening due to the insulation damage.
Check the electrical connection cables for damage
regularly. Make sure that the connection cable does
not hang on the power network during the inspection.
Electrical connection cables must comply with the ap-
plicable VDE and DIN provisions. Only use connection
cables of the same designation.
The printing of the type designation on the connection
cable is mandatory.
AC motor:
• The mains voltage must be 230-240 V~.
• Extension cables up to 25 m long must have a
cross-section of 1.5 mm².
• Connections and repairs of electrical equipment
may only be carried out by an electrician.
Anschlussart X
Wenn die Netzanschlussleitung dieses Gerätes be-
schädigt wird, muss sie durch eine besondere An-
schlussleitung ersetzt werden, die vom Hersteller oder
seinem Kundendienst erhältlich ist.
www.scheppach.com GB | 31