Related Manuals for Hyundai HTRT4140-1
Summary of Contents for Hyundai HTRT4140-1
- Page 1 PETROL CHAINSAW HTRT4140-1 WARNING: Read thoroughly the instruction manual before use.
-
Page 2: Table Of Contents
CONTENTS SECURITY INSTRUCTIONS YOUR PRODUCT ASSEMBLY FILLING THE FUEL TANK AND OIL TANK OPERATION MAINTENANCE AND STORAGE DECLARATION OF CONFORMITY WARRANTY PRODUCT FAILURE WARRANTY EXCLUSIONS... -
Page 3: Security Instructions
1. SAFETY WARNINGS WARNING! When using this type of tool, basic precautions should always be followed to reduce the risk of fire, electric shock and injury. Read all instructions carefully before attempting to use this product and retain these instructions. - Page 4 Keep handles dry, clean and free from oil and grease. Be concentrated when using the tool. Look at what you do, make sense and do not use the tool when you are tired. Remove the blade guard before using the tool. ...
- Page 5 whose tension and lubrication are incorrect can either break or increase the risk of rebound. Keep handles dry, clean and free of oil and grease. Oily, greasy grips are slippery and cause loss of control. Cut only wood, as well as for pruning and cutting wood. Do not use the chain saw for any ...
- Page 6 Hold the saw with both hands firmly with the thumbs and fingers encircling the handles of the saw and place your body and arms to allow you to withstand the rebound forces. The rebound forces can be controlled by the operator, if appropriate precautions are taken. Do not allow chain saw to start.
-
Page 7: Your Product
Do not operate the tool with one hand. Always hold it with both hands. Wear protective gloves Wear protective foot wear. Do not use the too under rain 2. YOUR PRODUCT a. Description 7- Oil vacuole 1- Cover-rear handle 8- Brake 2- Trigger 9- Chain adjusting tension 3- Choke lever... - Page 8 Technical data Model HTRT4140-1 Type of engine RY1E40F Fuel Tank Volume 260cm³ Oil tank volume 210cm³ Idle speed of the engine 3100±300/min Engine speed with clutch engage 4300/min Maximum power 1.4kW Displacement 41cm³ Maximum engine power speed 8000/min Maximum engine speed...
-
Page 9: Assembly
3. ASSEMBLY a. Assembly of the chain guide IMPORTANT: The machine must not be started during assembly. Wear protective gloves when handling the blade. 1) Pull the lever of the hand wheel and to unscrew the hand wheel. Remove then the chain cover. -
Page 10: Filling The Fuel Tank And Oil Tank
4. FILLING THE FUEL TANK AND OIL TANK 1) Filling fuel tank WARNING: When filling the tank: The chainsaw must always be stopped and cooled. Never smoke during refueling. It must not have flames or sparks near the fuel. Before refueling, allow the chainsaw to cool completely. Do not attempt to refuel when the engine is hot. - Page 11 c. Storage of fuel The fuel must be kept in a clean and safe container and always closed. If you are not using the product for a long time, remove the fuel mixture and add it to a container. Do not leave the fuel for a long time in the product. The fuel may clog the carburetor and the engine will not operate properly.
-
Page 12: Operation
5. OPERATION Before using the chainsaw, inspect the work area. This must be cleared. Remove any branches, obstacles and other items that may cause damage during cutting. The unit should always be filled with fuel and useful. Check the level of filling and refill when necessary. - Page 13 Pull the choke lever. It will close and the throttle will be moved to the starting position Hold the chainsaw firmly against the ground. Put the chainsaw: Either on the left side of your body holding the handle firmly with your left hand. ...
- Page 14 b. Stopping the engine Allow the chainsaw to run for a few minutes. Then turn the switch to the OFF position. 1. Main settings a. Adjusting the carburetor The carburetor is preset at the factory. To avoid malfunction, it is recommended not to adjust the adjustment screws.
- Page 15 d. Sharpening of the chain For best performance, we strongly recommend that you periodically sharpen the chain. The chain can either be sharpened by a professional or by yourself by providing you with a sharpening guide (make sure you know how to use it). The chain must be sharpened when: Wood chips have become powder To make a normal cut, force on the tool...
- Page 16 b. Trunk on the ground Cut half of the trunk, turn it over and finish the cut on the other side. c. Trunk in elevation Begin by cutting a first part from below and then from above. Then, on the second part, repeat this operation.
-
Page 17: Maintenance And Storage
6. MAINTENANCE AND STORAGE 1. Maintenance Before any maintenance work, the machine must be switched off and completely cooled. Perform the maintenance work according to the instructions below and perform them regularly. A clean, well-maintained machine increases its standard of living and efficiency. - Page 18 e. Sprocket Check the sprocket on signs of wear. If wearing is important, replace it with a new one. Do not install a chain on a worn or damaged sprocket. Do not install a worn chain on a pinion. Spark plug Clean the electrodes with a wire brush and set the gap to 0.6mm if necessary.
- Page 19 h. Sharpening of the chain For best performance, we strongly recommend that you periodically sharpen the chain. The chain can either be sharpened by a professional or by yourself by providing you with a sharpening guide (make sure you know how to use it). The chain must be sharpened when: Wood chips have become powder To perform a normal cut, force on the tool#...
-
Page 20: Declaration Of Conformity
Declaration of conformity BUILDER ZI, 32 rue Aristide Bergès – 31270 Cugnaux - France Declares that the machinery designated below: Petrol chainsaw HTRT4140-1 Serial number: 20210752700-20210752849 20210752850-20210752999 Complies with the provisions of the Directive "machinery" 2006/42/EC and regulations National transposing it;... -
Page 21: Warranty
8. WARRANTY WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. The manufacturer agrees to replace parts identified as defective by the designated distributor. -
Page 22: Product Failure
9. PRODUCT FAILURE WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: a) Empty the fuel tank. b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine. -
Page 23: Warranty Exclusions
10. WARRANTY EXCLUSIONS THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. • Damage resulting from improper use of the product. • Damage resulting from assembly or start-up not in accordance with the user manual. •...