Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hyundai HY3810
Summary of Contents for Hyundai HY3810
- Page 1 CHAIN SAW HY3810 HY4110 Instruction Manual...
-
Page 4: Before The First Use
BEFORE THE FIRST USE Be sure to read the full instructions! Read the user manual before use before first use. Instructions contain important information for the safe use of this product. Add fuel There is no fuel in the engine! Fuel must be added to the tank before use. - Page 5 Instruction manual · This instruction manual applies for this device. It contains important information for starting the use and handling with the product. · Before you start using the device, read the instruction manual carefully and in its entirety, specially the safety instructions. Failure to follow this instruction manual can result in serious bodily injuries or damage to the device.
-
Page 6: General Safety Instructions
GENERAL SAFETY MEASURES Read all the safety warnings and instructions that are included in the manual. Failure to observe the safety warnings and instructions may result in the risk of exposure of people and domestic pets to electric shock, fire and / or serious injuries. -
Page 7: Environmental Requirements
alcohol or medicines. A moment of carelessness when using the tool can cause serious personal injury. Environmental requirements Do not expose the tools to rain or moisture. Safety of persons · Wear head, eye, hands and hearing protection when using the tool. ·... -
Page 8: Adding Fuel
· If you use a chainsaw in or after rain, particular consideration should be given to the precautionary measures, as the soil can be very slippery. · Children, other persons and animals must not be in the vicinity when using a chainsaw. In the event of a distraction, you can lose control of the chainsaw. - Page 9 Do not use a chainsaw if it is damaged or does not work reliably. · Always hold the chain saw with the right hand for the rear handle and with the left hand for the front handle. Holding a chainsaw the other way increases the risk of injury and must not be done.
- Page 10 · Turn the engine off before checking the tension of the chain, before replacing the chain, before removing the chain and before removing the faults! For maintenance work, extract the plug from the spark plug to prevent accidental starting of the engine. ·...
-
Page 11: Designated Use
the tip of the sword and allows better control of the chainsaw in unexpected situations. · Always use replacement bars and chains recommended by the manufacturer. The wrong replacement bar and the chain can lead to a chain breakage and / or kickback. ·... -
Page 12: Installing The Guide Bar And Chain
C. Mandatory use of protective equipment for protection of the head, hearing and eyes. D. Mandatory use of protective gloves. E. Mandatory use of protective safety shoes. F. Noise level G. Refuelling cap H. Chain oil cap I. Fuel pump membrane J. -
Page 13: Chain Oil
the hook on the motor unit. Pull up the chain and tighten the tensioning screw with a screwdriver to tighten the chain. (A3) 8. Now you can screw the tensioner nut with the supplied key. 9. Check the chain before working. The chain must move if you drag it by hand. - Page 14 fuel flows into the pump. 2. Move the On / Off button to the "I" position. (B1) 3. Push the choke out to position 1. (B2) 4. Firmly grasp the front handgrip with your left hand, and the ignition handgrip with your right hand. (B3) 5.
- Page 15 WARNING! If the brake does not work properly, take the chainsaw to an authorized service. Cutting down trees WARNING! Carefully read and follow all instructions before starting work! Logging 1. Determine the direction of the fall according to the wind, the angle of the tree, the direction of growth of heavy branches and similar factors.
-
Page 16: Maintenance
Supported trunk (C3) ·In zone A, cut from the bottom first and finish cutting down from the top. ·In zone B, cut from the top first and finish cutting up from the bottom. Cutting the branches of a fallen tree (C4) First, check which side of the branch is curved. -
Page 17: Storage And Transport
Tensioning the chain The chain tensioning screw is located on the right side of the device under the tensioner nut. ·Tighten the chain tensioning screw with a screwdriver to tension the chain. ·Unscrew the screw to release the chain. Sharpening the chain A round file and a template is used for grinding the cutter teeth. -
Page 18: Specifications
Specifications Model: HY3810 Engine type: 2-stroke Engine volume: 37 cm Engine cooling: Air-cooled Engine power 1,2 kW Rotation speed: 2.700 - 12.000 min Oil and fuel mixture: 40:1 (2.5%) - oil for two-stroke engine Fuel tank capacity: 310 ml Oil tank capacity:... - Page 19 Model: HY4110 Engine type: 2-stroke Engine volume: 40.1 cm Engine cooling: Air-cooled Engine power 1,2 kW Rotation speed: 2.700 - 12.000 min Oil and fuel mixture: 40:1 (2.5%) - oil for two-stroke engine Fuel tank capacity: 310 ml Oil tank capacity: 200 ml Starting system: Manual startup...