S&A CW-5300 User Manual
  1. Manuals
  2. Brands
  3. S&A Manuals
  4. Chiller
  5. CW-5300
  6. User manual

S&A CW-5300 User Manual

Industrial chiller
Hide thumbs Also See for CW-5300:

Advertisement

Table of Contents

TY-JS-20319-003
CW-5300/6000/6100/6200/6260
Industrial Chiller
User Manual
1

Advertisement

Table of Contents
loading

Related Manuals for S&A CW-5300

Summary of Contents for S&A CW-5300

  • Page 1 TY-JS-20319-003 CW-5300/6000/6100/6200/6260 Industrial Chiller User Manual...
  • Page 2 TY-JS-20319-003 FOREWORD Thanks for your purchase of our product. Please read this manual carefully before using and keep it properly so that you can refer to it whenever you need information. This manual is not a quality guarantee. Our company reserves the right to the interpretation of the correction of misprint and improperly described information and product improvement.

  • Page 3: Table Of Contents

    TY-JS-20319-003 CONTENTS Notice-----------------------------------------------------------------------------------------4 I. Overview----------------------------------------------------------------------------------7 II. Model Illustration--------------------------------------------------------------------- 7 III. Product Outlines & Parts----------------------------------------------------------8 IV. Installation------------------------------------------------------------------------------9 V. Operating States &Parameters Adjustment--------------------------------- 11 VI. Alarm & Output Terminal----------------------------------------------------------14 VII. Maintenance-------------------------------------------------------------------------- 15 VIII. Simple Troubleshooting--------------------------------------------------------- 16 Attachment – Schematic---------------------------------------------------------------- 17...

  • Page 4: Notice

    TY-JS-20319-003 Notice In order to ensure your personal safety and avoid property loss, you must pay attention to this manual, but not limited to the following warning notices. General electric knowledge and safety standards should also be followed. DANGER Failure to take safety measures will result in death or serious personal injury.
  • Page 5 TY-JS-20319-003 DANGER Failure to take safety measures will result in death or serious personal injury. Notice Operation Guideline The equipment must be firmly fixed during transport and Transport and installation. Otherwise, there will be a danger of tipping or installation falling.
  • Page 6 TY-JS-20319-003 air inlet and 1.5 meters around the air outlet. If the air inlet and the air outlet are blocked, the cooling ability that the equipment should have cannot be realized. a) Make sure that the water supply pipe of equipment is not blocked;...

  • Page 7: Overview

    TY-JS-20319-003 I. Overview This product is an industrial cooling device designed and manufactured for laser cutting, laser welding, laser marking, laser engraving and other equipment that uses laser processing. It can provide a temperature-stable cooling medium for the above application scenarios.

  • Page 8: Product Outlines & Parts

    TY-JS-20319-003 III. Product Outlines & Parts Temperature Controller Power Switch Air Outlet Water Inlet Water Supply Inlet Water Outlet Air Inlet Water Level Gauge (Filter Gauze) Alarm Output Port Electrical Drain Connecting Note: The above-mentioned product outlines and part names are only for one of the models. The outlines and parts installation may be slightly different in different models.

  • Page 9: Installation

    TY-JS-20319-003 IV. Installation 1. Open the package and check whether the machine is in good condition and whether the accessories are complete. 2. Please ensure that the working voltage of the chiller is stable and normal. Because the refrigeration compressor is sensitive to the power supply voltage, the normal working voltage of our company's standard products is 210~240V (110V model is 100~120V).
  • Page 10 TY-JS-20319-003 free of impurities, so as to prevent impurities from entering the waterway and causing blockage or pump failure. 5. Plug in the power cord and turn on the power switch(It is forbidden to start without water). (1) After turning on the power switch, the circulating pump of the chiller starts to work. When the new machine is turned on for the first time, there will be more air bubbles in the pipeline, which will cause the machine to alarm occasionally, and it will return to normal after a few minutes of operation.

  • Page 11: Operating States &Parameters Adjustment

    TY-JS-20319-003 (2) Exhaust Air After adding water for the first time or replacing water, exhaust the air in the water pump to start use, otherwise the equipment will be damaged. The exhaust method is as follows ： Method 1: Under the state of shutting down, after adding water, remove the water outlet and connect the water pipe, drain for 2 minutes, and then install it firmly.
  • Page 12 TY-JS-20319-003 controller. Press “RST” key to save the data and exit. 4.Press key once to enter status display menu and it indicates t1 which suggests temperature of room temperature sensor. Press key twice to indicate t2 which suggests flow rate. Press key three times to return to normal operation.

  • Page 13: Alarm & Output Terminal

    TY-JS-20319-003 28.0℃ to 27.0℃). Case 2:Cooling water temperature is controlled by constant temperature control mode. Requiring water temperature to remain at 25 ℃ , and the water temperature fluctuation does not exceed ±2℃. The alarm of over high water temperature will be on when water temperature is 5℃...

  • Page 14: Maintenance

    TY-JS-20319-003 2. Alarm causes and working status table. Display Alarm Buzzer OUT H1、H2 OUT H1、H3 Condition code Circulating pump works properly Disconnection Breakover Ultrahigh room temperature alarm Sounds Breakover Disconnection Ultrahigh water temperature alarm Sounds Breakover Disconnection Ultralow water temperature alarm Sounds Breakover Disconnection...

  • Page 15: Simple Troubleshooting

    TY-JS-20319-003 VIII. Simple Troubleshooting Failure Failure Cause Approach Check and ensure the power interface Power cord is not plugged and the power plug is plugged in in place place and in good contact. Machine turned on but Open the electric box cover, check the unelectrified fuse and replace with a spare one if necessary.

  • Page 16: Attachment - Schematic

    TY-JS-20319-003 Attachment – Schematic CW-5300（flow sensor） CW-5300（flow switch）...
  • Page 17 TY-JS-20319-003 CW-6000（flow sensor） CW-6000（flow switch）...
  • Page 18 TY-JS-20319-003 CW-6100/6200（flow sensor） CW-6100/6200（flow switch）...
  • Page 19 TY-JS-20319-003 CW-6260（flow sensor）...

This manual is also suitable for:

Cw-6000Cw-6100Cw-6200Cw-6260

Table of Contents