Rehadapt Rehadapter Instructions For Use Manual page 15

4 4 U U s s i i n n g g t t h h e e R R e e h h a a d d a a p p t t e e r r ™ ™ – – U U s s e e r r
This section includes the instructions for use for the end-user. It includes all the information the end-user
needs to know to use the Rehadapter™ according to its intended purpose (as defined in Section 1.2). For
information about the initial setup of the Rehadapter™, refer to
Before using the Rehadapter™ for the first time, fully charge the battery

R R e e h h a a d d a a p p t t e e r r ™ ™ ) )
.
Only authorized distributors may set up and adjust the Rehadapter™. This is to avoid the risk of

damaging the Rehadapter™.
Comply with any notices and signs that limit or prohibit the use of mobile devices (for example in

healthcare facilities). Notwithstanding the fact that the Rehadapter was designed, tested and
manufactured to comply with regulations regarding radio frequency emissions, such emissions may
affect the operation of other electronic equipment and cause them to malfunction.
4 4 . . 1 1 T T u u r r n n i i n n g g t t h h e e R R e e h h a a d d a a p p t t e e r r ™ ™ o o n n / / o o f f f f
T T u u r r n n o o n n
To turn on the Rehadapter™, press and hold the volume up button
R R e e h h a a d d a a p p t t e e r r ™ ™ O O v v e e r r v v i i e e w w ) )
T T u u r r n n o o f f f f
To completely turn off the Rehadapter™, press and hold both volume buttons
seconds.
The Rehadapter™ will shut down by itself if there is no Bluetooth® connection with the tablet for 10

minutes.
4 4 . . 2 2 P P a a i i r r i i n n g g t t h h e e R R e e h h a a d d a a p p t t e e r r ™ ™ w w i i t t h h t t h h e e t t a a b b l l e e t t
To initially pair the Rehadapter™ with the tablet via
Bluetooth®, follow the steps below:
1. Turn on the tablet.
2. On the tablet, turn on Bluetooth®.
3. Turn on the Rehadapter™
T T u u r r n n i i n n g g t t h h e e R R e e h h a a d d a a p p t t e e r r ™ ™ o o n n / / o o f f f f ) )
4. Activate Pairing Mode: Press and hold one
volume button
the other volume button for 4 times one
second each. When the status indicator starts
blinking quickly in blue, let go of both buttons.
5. On the tablet, go to Bluetooth® settings, and
tap the name of the Rehadapter™

( Rehadapter-XXXXXX as shown on
The status indicator LED is solid blue.
Pairing is only possible for 1 minute.

If the Rehadapter™ is not paired with a new device within 1 minute, the Rehadapter™ will shut down

by itself.
The Rehadapter™ can only be connected with one tablet at the time.

.
( ( S S e e c c t t i i o o n n 4 4 . . 1 1
.
 
or while slowly pressing
F F i i g g . . 4 4 . . 1 1
C C h h a a p p t t e e r r 5 5
.
Figure 4.1 Device identification label
of the Rehadapter™
). The Rehadapter™ is now paired with the tablet.
1 1 5 5
( ( S S e e c c t t i i o o n n 6 6 . . 1 1 . . 2 2 C C h h a a r r g g i i n n g g t t h h e e

( ( F F i i g g . . 3 3 . . 1 1
for 3 seconds
 
and
 on the back
for 5