Download Print this page
Extron electronics VN-Matrix 325 Setup Manual
Extron electronics VN-Matrix 325 Setup Manual

Extron electronics VN-Matrix 325 Setup Manual

Hide thumbs Also See for VN-Matrix 325:

Advertisement

Quick Links

VN-Matrix
325 Codecs • Setup Guide
®
The Extron VN-Matrix 325 encoders/decoders (codecs) distribute digital SD, HD-SDI, or 3G-SDI
video using the Extron PURE3
configured as an encoder are compressed into a TCP or RTP data stream for transport across a
local area or wide area network. At the far end of the network, one or more VNC 325 codecs
configured as decoders convert the compressed stream back
into the original video signal format.
NOTE
: For full installation, configuration, and operation
details, see the VN-Matrix 325 User Guide, available
at www.extron.com.
Connections
NOTES
: • See
"Initial Setup — Before You Connect to a
Network," step 2 for the RS-232 protocol for the
Remote port ( a )
• The protocol for the RS-232 Over LAN port (
configurable and beyond the scope of this guide.
Connections — Either Configuration
NOTE
: The VNC 325 products use male connectors for
ports
a
and
b
a
Remote 1 port — Use this male 9-pin port to configure
the connected VN-Matrix 325 unit only.
b
RS-232 Over LAN port — Use this male 9-pin port to transmit and receive data across a network.
NOTE
: Do NOT connect VN-Matrix units to an existing network until each is correctly configured. Incorrect configuration may
cause disruption to other network users. See
c
LAN port 1 (RJ-45 port) — Use either this port or the fiber optic network port (
network, to control the VN-Matrix system, or both.
d
LAN port 2 (fiber optic port) — Use either this port or the RJ-45 network port (
network, to control the VN-Matrix system, or both.
NOTE
: Extron does not supply the the plug-in SFP module for the optical Network port.
e
Power Connector — Connect the included 12 V power supply between this connector
and a 100 VAC/240 VAC, 50-60 Hz source.
Video Connections — Encoder Configuration
f
SDI In BNC connector — Connect a digital video input for encoding and streaming to
one or more decoders.
g
Out BNC connector (optional) — This connector provides a loop through of the original source
with or without an optional text overlay.
h
Loop BNC connector (optional) — This connector provides a buffered loop through of the
original source.
Video Connections — Decoder Configuration
f
SDI In BNC connector (optional) — If desired, connect a digital genlock signal to synchronize
the decoder to a genlock signal.
g
SDI Out BNC connector — Connect a digital video display to receive the streamed digital video
output. When no video streams are being decoded, this output can provide either a frozen
image of the last received frame or a splash screen that masks the output.
h
Loop BNC connector — Not used.
codec. Video signals that are connected to a VNC 325 device
®
.
. You may need an adapter.
IP address: 192.168.0.101
IP address: 192.168.0.101
Subnet mask: 255.255.255.0
Subnet mask: 255.255.255.
LAN-1
LAN-2
TEST
STATUS
ALARM
Controller
Controller
IP address: 192.168.0.103
IP address: 192.168.0.103
Subnet mask: 255.255.255.0
Subnet mask: 255.255.255.0
LAN-1
LAN-2
TEST
STATUS
ALARM
b
) is
Typical VN-Matrix 325 Application
Figure 1.
POWER
12V DC
1
LAN
3A MAX
5
3
VN-Matrix Connections
Figure 2.
"Initial Setup — Before You Connect to a
d
c
IP address: 192.168.0.102
IP addre
ess: 192.168.0.102
.0
Subnet mask: 255.255.255.0
Subnet m
mask: 255.255.255.0
LAN-1
LAN-2
TEST
STATUS
ALARM
VN-MATRIX 325 SERIES
ATRIX 325 SERIES
SERIAL DIGITAL VIDEO OVER IP
AL DIGITAL VIDEO OVER IP
IP address: 192.168.0.104
IP addre
ess: 192.168.0.104
Subnet mask: 255.255.255.0
Subnet
mask: 255.255.255.0
LAN-1
LAN-2
TEST
STATUS
ALARM
VN-MATRIX 325 SERIES
ATRIX 325 SERIES
SERIAL DIGITAL VIDEO OVER IP
L DIGITAL VIDEO OVER IP
1
REMOTE
OPTICAL
SDI
OUT
2
4
7
Network" to configure the units.
) to stream video and audio data across a
) to stream video and audio data across a
3
POWER
OPTICAL
SDI
12V DC
OUT
1
LAN
2
3A MAX
Encoder Configuration
Camera
Network
POWER
12V DC
3A MAX
Decoder Configuration
VN-MATRIX 325 SERIES
SERIAL DIGITAL VIDEO OVER IP
VN-MATRIX 325 SERIES
SERIAL DIGITAL VIDEO OVER IP
2
RS-232
OVER LAN
SDI
IN
6
8
Network
REMOTE
RS-232
OVER LAN
SDI
IN
6
8
Monitor
3
REMOTE
RS-232
OVER LAN
OPTICAL
SDI
SDI
OUT
IN
1
LAN
2
Decoded
7
Video
Monitor

Advertisement

loading

Summary of Contents for Extron electronics VN-Matrix 325

  • Page 1 VN-Matrix 325 Codecs • Setup Guide ® The Extron VN-Matrix 325 encoders/decoders (codecs) distribute digital SD, HD-SDI, or 3G-SDI video using the Extron PURE3 codec. Video signals that are connected to a VNC 325 device ® configured as an encoder are compressed into a TCP or RTP data stream for transport across a local area or wide area network.
  • Page 2 The controller can be any unit in the system, whether configured as an encoder or decoder. In figure 1 on page 1, the VN-Matrix 325 unit at 192.168.0.101 is designated as the controller. Each VN-Matrix 325 device in the system should be set to recognize the IP address of the device controller.
  • Page 3 Startup and Login After you have made all network connections, cycle power on each VN-Matrix 325 unit to ensure that the other network components, such as hubs and switches recognize the power up of the units and begin exchanging data with them.
  • Page 4 NOTE : Choose rtp for unicast RTP streaming or tcp for unicast TCP streaming. See the VN-Matrix 325 User Guide for more information about these data transport methods. Click the Save All button to save the configuration changes.