Camera Control Unit Rear Panel - Panasonic AK-HCU931 Operating Instructions Manual

Parts and their functions

$ Camera control unit rear panel

A
RET1
HD
RET1
SD
WFM1
SD
I
P U S H
COMMUNICATION IN RTS
P Q
A Optical fiber connector
FXW.3K.93C.CLM made by LEMO
Pin
Function Polarity
No.
1 Optical fiber
2 Optical fiber
3 Control wire, hot
4 Control wire, cold
5 AC 240 V live
6 AC 240 V neutral
B HDTV digital return video 1, 2, 3, 4 input connectors
[HD DIGITAL RET 1, 2, 3, 4] (Option)
These connectors (BNC) are for inputting the return video
signals of the HDTV serial digital interface.
C HDTV digital video 1, 2, 3, 4 output connectors
[HD DIGITAL OUT 1, 2, 3, 4] (Option)
These connectors (BNC) are for outputting the video sig-
nals of the HDTV serial digital interface.
D HDTV analog component video output connectors
[HDTV ANALOG Y/G, Pb/B, Pr/R] (Option)
The HDTV analog signals of the camera are output from
these connectors (BNC).
G/B/R or Y/Pb/Pr video signals can be selected by the
master setup unit (MSU) or remote operation panel
(ROP).
SDTV PM output connector [PM]
This is the HDTV PM output (1Vp-p) connector.
C
B
RET2 RET3 RET4 OUT1 OUT2
SDI INPUT SDI OUTPUT
RET2 RET3 RET4 OUT1 OUT2
E F
SDI INPUT SDI OUTPUT
WFM2 PM1 PM2 VBS1 VBS2
J K
OUTPUT
OUT CH–1 MIC OUT CH–2 DIGITAL AUDIO
R S T U
Signal flow Cable color
CAM#CCU Yellow (01)
CCU#CAM
Yellow (02)
CAM,.CCU Black
i
CAM,.CCU Red
j
CCU#CAM Orange
i
CCU#CAM White
j
D
OUT3 OUT4/PM Y / G Pb / B Pr / R
OUTPUT
OUT3 OUT4 RET1 RET2 PROMPT
G H
INPUT 1
1
HD SD HD REF SD REF
L M
N O
SYNC OUTPUT
TRUNK WFM CONTROL
V W
ROP
AUX
X
Y
E SDTV digital return video 1, 2, 3, 4 input connectors
[SDTV DIGITAL RET 1, 2, 3, 4]
These connectors are for inputting the return video sig-
nals of the SDTV serial digital interface.
F SDTV D1 digital video output connectors
[SDTV DIGITAL OUT D1 1, 2 3]
These connectors are for outputting the D1 format video
signals of the SDTV serial digital interface.
There are 3 connectors (BNC).
G Analog return video 1, 2 input connectors
[ANALOG RET 1, 2]
These connectors (BNC) are for inputting the SD analog
return video signals.
H PROMPT-IN connectors [PROMPT1,2]
These are the prompter signal input connectors (BNC).
Input SDTV composite video signals as the prompter sig-
nals.
I SDTV waveform monitor output connectors
[SDTV WFM 1, 2]
These connectors (BNC) are for outputting the camera
video signals which are to be displayed on the SDTV
waveform monitor.
ROP/MSU monitor selection
R
G
B
SEQ
ENC
[
PM
HD
SD
2
2
AC IN
ALARM
CSU / MSU
Z
GND
\
^
SDTV WFM output
R
G
B
RGB 3 waveforms
Composite video
]
5