Panasonic AK-HCU931 Operating Instructions Manual page 6

Parts and their functions
$ Camera control unit rear panel
A
RET1
HD
RET1
SD
WFM1
SD
I
P U S H
COMMUNICATION IN RTS
P Q
J SDTV picture monitor video output connectors
[PM 1, 2]
These connectors (BNC) are for outputting the video signals
which are to be displayed on the SDTV picture monitor.
ROP/MSU monitor selection
R
G
B
SEQ
ENC
K SDTV analog composite video output connectors
[SDTV VBS]
These connectors (BNC) are for outputting the SDTV ana-
log composite video signals (with sync) of the camera.
L HDTV analog SYNC output connector [HD SYNC]
The HDTV analog sync signal of the camera is output
from this connector (BNC). Its amplitude is +/-0.3 V (75h
termination).
M SDTV analog SYNC output connector
[SDTV ANALOG SYNC]
The SDTV analog sync signal of the camera is output
from this connector (BNC). Its amplitude is 2 Vp-p (75h
termination).
N HDTV genlock input connectors [HD REF]
These are the HDTV genlock input connectors (BNC).
The bridging connection between the two connectors
enables one to be used for input purposes and the other
for output purposes.
Input the HDTV tri-level sync signal as the genlock signal.
O SDTV genlock input connectors [SDTV REF]
These are the SDTV genlock input connectors (BNC).
The bridging connection between the two connectors
enables one to be used for input purposes and the other
for output purposes.
Input the BB video signal as the genlock signal.
6
C
B
RET2 RET3 RET4 OUT1 OUT2
SDI INPUT SDI OUTPUT
RET2 RET3 RET4 OUT1 OUT2
E F
SDI INPUT SDI OUTPUT
WFM2 PM1 PM2 VBS1 VBS2
J K
OUTPUT
OUT CH–1 MIC OUT CH–2 DIGITAL AUDIO
R S T U
SDTV PM1 output
Rialarm display
Gialarm display
Bialarm display
Y and skin tone zebra pattern
Composite video
D
OUT3 OUT4/PM Y / G Pb / B Pr / R
OUTPUT
OUT3 OUT4 RET1 RET2 PROMPT
G H
INPUT 1
1
HD SD HD REF SD REF
L M
N O
SYNC OUTPUT
TRUNK WFM CONTROL
V W
ROP
AUX
X
Y
P INCOM/tally connector [COMMUNICATION]
The external INCOM or tally system is connected here.
INCOM/tally connector (KPT02E14-19P made by Japan
Aviation Electronics Industry)
Pin No. Function
A
Shield
B
INCOM 1
C
INCOM 1
D
INCOM 1
E INCOM 1
F
INCOM 2
G
INCOM 2
H
INCOM 2
J
INCOM 2
K PGM1(H)
L
PGM1(C)
M
PGM2(H)
N
PGM2(C)
P
NC
R
Red tally
S
Green tally
T NC
U
NC
V
Tally common
PGM output level: 0 dBm/600h
INCOM level: 0 dBm/600h
[
PM
HD
SD
2
2
AC IN
ALARM
CSU / MSU
Z
GND
\
]
^
Polarity Signal flow
CCU#SYSTEM
i
CCU#SYSTEM
j
SYSTEM#CCU
i
SYSTEM#CCU
j
CCU#SYSTEM
i
CCU#SYSTEM
j
SYSTEM#CCU
i
SYSTEM#CCU
j
SYSTEM#CCU
i
SYSTEM#CCU
j
SYSTEM#CCU
i
SYSTEM#CCU
j
Contact
Contact