VE01-B22L / VE01-B23L User Manual Remark Please follow the user manual for correct installation and testing. If there is any doubt please call our tech-supporting and customer center. Our company applies ourselves to reformation and innovation of our products. No further notice for any change. The illustration shown here is only for reference.
VE01-B22L / VE01-B23L User Manual Product description Application VE01-B23L is outdoor panel based on TCP/IP communication protocal, supporting digital video intercom and SIP communication protocol. Operating system : Linux...
VE01-B22L / VE01-B23L User Manual Basic function ◇ Call indoor monitor by one button; ◇ Support unlocking by IC/ID access control card or password(ID Optional); (Note: this function is only applicable to the panel with card swiping function.) ◇ IC/ID card information can be registered on outdoor panel. Registration information of max.
VE01-B22L / VE01-B23L User Manual Basic operation 1. Call indoor monitor In standby mode, press the call button on outdoor panel to call indoor monitor. During the call, press the call button on outdoor panel again to end the call. If the call fails or indoor monitor is busy, outdoor panel will emit a beep.
VE01-B22L / VE01-B23L User Manual WEB settings Connect outdoor panel to PC through the switch. Input IP address of outdoor panel in the web browser of PC (The IP addresses of PC and outdoor panel must be in the same network segment.
VE01-B22L / VE01-B23L User Manual DHCP: dynamic IP function. IP address: for the same system on the same network segment, IP address can not be repeated. Subnet mask: the original subnet mask is 255.255.255.0, which normally doesn't need to be changed.
VE01-B22L / VE01-B23L User Manual System volume: adjust the system volume with 6 levels for selection. Video size: 320x240, 640x480 or 1280x720. Call forwarding: the call can be made one by one or simultaneously. After the setup is completed, click the icon “Submit" to enable the settings.
VE01-B22L / VE01-B23L User Manual Then register the user card. The user shall swipe the admin card first. The system emits a beep. Then place the card to be registered near the swiping area within 10 seconds. When the system gives an indication tone, it means that the user card is registered successfully.
VE01-B22L / VE01-B23L User Manual 6. Call Forwarding Click the icon "Forward" on the left side of the page to enter the interface as shown below: The room number can be bound with the telephone number. When a visitor calls but there is no answer within 25 seconds, the system will automatically forward the call to the phone.
Page 15
VE01-B22L / VE01-B23L User Manual Quick Call: Check the box to enable this function. It refers to the call to management center. Enter the SIP address of specified management center device in the box after URL. The device can be indoor monitor or SIP phone of other manufacturers.
VE01-B22L / VE01-B23L User Manual Other Settings Click the icon "Others" on the left side of the page to enter the interface as shown below: Click Reboot to restart the system. Logout Click the icon "Logout" on the left side. In next page, click the icon "Submit" to log out...
VE01-B22L / VE01-B23L User Manual Wiring diagram of outdoor panel Network&POE Power/Switching Value Output/Exit/ RS485 Door Magnetic DC12V 485+ 485- VE01-B22L/VE01-B23L Network Power/Switching Value Output/Exit/ RS485 Door Magnetic DC12V 485+ 485- VE01-B22L/VE01-B23L...
VE01-B22L / VE01-B23L User Manual RS485 interface It can connect to the equipment with RS485 interface. RS485 interface can output 12V/100mA power. Connection of +12V isn't required if it is unused. +12V +12V RS485 interface RS485 equipment 2. Exit Button/Door Magnetic Switch Connect with Exit button and door magnetic switch;...
VE01-B22L / VE01-B23L User Manual 3. Network Interface Connect to management center, indoor monitor or other network device through network switch. CAT-5e network interface Power/Switching value output Connect power interface of outdoor panel to 12V DC power. Switching value output connects with electric lock. Independent power supply is required for the lock.
VE01-B22L / VE01-B23L User Manual 6. RS485/Switching Value Output/Exit/Door Magnetic +12V +12V RS485 equipment 485+ 485+ 485- 485- Normally-closed connection of relay Common port of relay Normally-open connection of relay EXIT Exit button Exit Magnetic detection switch Door Magnetic RS485...
VE01-B22L / VE01-B23L User Manual Troubleshooting Some common failures and troubleshooting methods are listed for your reference. In case of failure which cannot be repaired, do not disassemble or repair the product by yourself. Please contact the after-sales service department.
VE01-B22L / VE01-B23L User Manual Safety & Precautions Safety & Precautions To protect you and others from harm or protect your device from damage, please read the following information before using your device. Do not install equipment in the following areas: Do not install equipment in high temperature, humidity, near the magnetic field, such as generators, transformers or magnets, etc.