Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for PLANET ECLIPSE ETHA3
Summary of Contents for PLANET ECLIPSE ETHA3
- Page 1 Planet eclipse: etha3 SUB TITLE User manual: english .68cal etha3...
- Page 2 Only use professional paintball fields where codes of safety are This User Manual is in English. Always fit a barrel-blocking device to the marker when not in use. PLANET ECLIPSE PAINTBALL EQUIPMENT IS NOT A TOY. strictly enforced. PAINTBALL SAFETY RULES MUST BE FOLLOWED AT ALL It contains important safety guidelines and Always remove paintballs from the marker when not in use.
-
Page 3: Table Of Contents
All Eclipse products undergo meticulous checks our worldwide technical support network that will by experienced specialists who care about the Switching The ETHA3 On/Off Solenoid Assembly help you with any technical problems from product that arrives at your door. Precision... -
Page 4: Sub Title
Do not pressurise the marker without the bolt system correctly installed, as high pressure gas will be emitted. Do not install a compressed air system or load paintballs into the marker until you feel confident with your ability to handle the marker safely and responsibly. Etha3 Etha3 etha3 etha3... -
Page 5: Led Status Indicator
Fig.1 SUB TITLE SWITCHING THE ETHA3 ON/OFF LED STATUS INDICATOR PUSH BUTTON SAFETY The frame houses the On/Off button BATTERY STATUS Fig.1 the status indicator . Use the On/Off button to switch the marker On/Off. Tap the On/Off button when the marker is On. -
Page 6: Velocity Adjustment
NEVER point your marker in the direction of other people when not on the field. If the pre-travel screw is wound in too far this could ALWAYS be aware of where the barrel is facing when adjusting the velocity. cause the marker to fire unintentionally. 1/8” Etha3 Etha3 etha3 etha3... -
Page 7: Unloading The Marker
Do not pressurise the marker without the bolt system correctly installed, as high pressure gas will be emitted. Do not install a compressed air system or load paintballs into the marker until you feel confident with your ability to handle the marker safely and responsibly. Etha3 Etha3 etha3 etha3... -
Page 8: Storage And Transportation
Never carry your marker un-cased when not on a playing field. The non-playing public and law enforcement personnel may not be able to distinguish between a paintball marker and a real firearm. For your own safety, and to protect the image of paintball, always carry the paintball marker in a suitable marker case, such as the one in which it was supplied. Etha3 Etha3... -
Page 9: The Set-Up Mode
If a parameter does not support tenths, this will be skipped. A long LED flash indicates the unit, whilst a short LED flash indicates the tenth. E.g. 5 long flashes and 3 short flashes would indicate 5.3. Etha3 Etha3 etha3... - Page 10 Replace the battery base , ensuring the side tabs click and lock into place. Push the bottom locking tab back in place to lock the unit. DO NOT use rechargeable batteries. DO NOT use poor quality batteries. 1/8” Etha3 etha3...
-
Page 11: Fault Finding Tables
The PCB is damaged. Replace the PCB. Clean, lubricate or replace the 14x2 NBR70 o-ring towards the back Dirty or damaged rear bolt guide o-ring. of the bolt guide. The solenoid valve is damaged. Replace the solenoid pilot valve. Etha3 etha3... - Page 12 The breech sensor turns itself off after firing and the The sensors are faulty. Replace the main circuit board. display shows a breech sensor fauly. The sensors are out of place. Make sure the breech sensors are pointing outwards. Etha3 etha3...
-
Page 13: Gamma Core Bolt Assembly (68Cal)
Rubber Detent Barrel O-Ring On/Off button (left side only) #016 NBR70 Solenoid Assembly 9V Battery Rear Frame Screw Light Pipe Front Frame Screw Breech Sensor E E Q E E N E E M E E O Etha3 Etha3 etha3 etha3... - Page 14 Solenoid Plate Adjuster Top M1.6 x 5 Machine Screws #008 NBR70 Internal O-Ring Solenoid Pilot #011 NBR70 External O-Ring Solenoid Plug Regulator Spring M2 x 16 Cross Pan head Screws Regulator Piston 14x2 NBR70 O-Ring Regulator Cap Etha3 Etha3 etha3 etha3...
- Page 15 #008 NBR70 O-Ring Bolt Guide #014 NBR70 O-Ring 14 x 2 NBR70 O-Ring #013 NBR70 O-Ring Bolt 14 x 2 NBR70 O-Ring #015 NBR90 O-Ring #013 NBR70 O-Ring #020 NBR70 External O-Ring #017 NBR70 Internal O-Ring Etha3 Etha3 etha3 etha3...
- Page 16 Repeat the steps in reverse order to reattach the grips to the frame. warning! When cleaning the frame, there are exposed operational elements that may be affected if wet. Etha3 Etha3 etha3 etha3...
- Page 17 Breech Cover Screw be able to alter/lock the marker settings. 6-32UNC x 5/16 See pages 16-17 for parameter settings and Countersunk socket screws status indicator. Breech Cover Light Pipe Rubber Detent Detent Recess Fig.2 Tournament Lock Button Breech Sensor Etha3 etha3...
-
Page 18: Frame Assembly
ETHA3 CIRCUIT BOARD FRAME ASSEMBLY FIG-1 Fig.1 Fig.1 CIRCUIT BOARD: TOP Circuit Board Tournament Lock Button Breech Sensors Solenoid Connector FIG-2 CIRCUIT BOARD: BOTTOM 9V Battery Terminals Push Button Switch LED Unit Fig.2 Microswitch Etha3 etha3... -
Page 19: Warranty
05, 15 Feed Neck 04, 07, 13, 30 On/Off 02, 04, 07–09, 13, 16, 21, 25 Set-Up 04, 16, 18, 21 YELLOW Frame 04, 08, 25, 31, 35 Parameters 09, 16–18, 21, 33 Solenoid 04, 20–21, 25, 27, 34–35 Etha3 etha3... - Page 20 Additional U.S. and International Patents may be pending. EUROPE Unit 14 Premier Park, Acheson Way 130 Franklin Street PE-Paintball.De Gmbh © Planet Eclipse Ltd. Trafford Park Road, Trafford Park Building L4 & L5 Langenberger Str. 9 Tor 5 & 6 5069__EN_ETHA3-Manual-V1...
Need help?
Do you have a question about the ETHA3 and is the answer not in the manual?
Questions and answers