Table of Contents
Advertisement
Operating Other Manufacturers' Video Equipment
To change the transmittable signals for operating a
CATV converter or DBS tuner ——————————
1.
Set the remote control mode to "CATV/DBS."
2.
Press and hold
3.
Press TV/DBS.
4.
Enter manufacturer's code (two digits) using
buttons 1 ~ 9, and 0.
See the list on below to find the code.
Examples: For a Echostar product, press 2 then 1.
For a Pioneer product, press 1 then 3.
5.
Release
TV/CATV/DBS.
After setting the remote control mode selector to "CATV/DBS,"
you can perform the following operations on the CATV convertor
or on the DBS tuner:
TV/CATV/DBS
CHANNEL +/–
1 ~ 10, 0, 100+ (+10) : Selects the channel.
Note:
• Refer to the manual supplied with your CATV converter or
DBS tuner.
6.
Try to operate your CATV converter or DBS tuner by
pressing
TV/CATV/DBS.
When your CATV converter or DBS tuner turns on or off, you
have entered the correct code.
If there are more than one code listed for your brand of CATV
converter or DBS tuner, try each one until the correct one is
entered.
Manufacturer
ECHOSTAR
GI JERROLD
HAMLIN/REGAL
PIONEER
RCA
SCIENTIFIC ATLANTA
SONY
ZENITH
Manufactures' codes are subject to change without notice. If they
are changed, this remote control cannot operate the equipment.
58
TV/CATV/DBS.
: Turns on and off the CATV converter
or DBS tuner.
: Changes the channels.
100+ (+10) button will function as the
ENTER button if your equipment
requires pressing ENTER after selecting a
channel number.
Code
21
01, 02, 03, 04, 05,
06, 07, 08
15, 16, 17, 18
13, 14
19
09, 10
20
11, 12
To change the transmittable signals for operating
another manufacturer's VCR ——————————
1.
Set the remote control mode to "AUDIO/TV/VCR."
2.
Press and hold
VCR.
3.
Press VCR.
4.
Enter manufacturer's code (two digits) using
buttons 1 ~ 9, and 0.
See the list on below to find the code.
Examples: For a JVC product, press 0 then 1.
For a Funai product, press 1 then 0.
5.
Release
VCR.
Following button can be used for operating the VCR (with the
remote control mode selector set to "AUDIO/TV/VCR"):
VCR : Turns on and off the VCR.
After pressing VCR or VCR CONTROL (with the remote
control mode selector set to "AUDIO/TV/VCR"), you can
perform the following operations on the VCR:
PLAY
: Starts playback.
1
: Rewinds a video tape.
¡
: Fast winds a video tape.
STOP : Stops operation.
PAUSE : Pauses.
¶ REC : Starts recording or enters recording pause.
After pressing VCR:
CHANNEL +/– : Changes the TV channels on the VCR.
1 ~ 10, 0, 100+ (+10) : Selects the TV channels.
100+ (+10) button will function as the
ENTER button if your VCR requires
pressing ENTER after selecting a channel
number.
Notes:
• Refer to the manual supplied with your VCR.
• You can use either VCR button or the VCR CONTROL
button to activate the buttons listed above. If you press VCR,
the playing source also changes. On the other hand, if you
press VCR CONTROL, the playing source does not change.
6.
Try to operate your VCR by pressing
When your VCR turns on or off, you have entered the correct
code.
If there are more than one code listed for your brand of VCR,
try each one until the correct one is entered.
Manufacturer
Code
JVC
01, 02, 03
EMERSON
11, 26
FISHER
29
FUNAI
10, 14, 15, 16 SANYO
GOLD STAR
12
HITACHI
04
MITSUBISHI 13
NEC
25
PANASONIC 07, 17
Manufactures' codes are subject to change without notice. If they
are changed, this remote control cannot operate the equipment.
VCR.
Manufacturer
Code
PHILIPS
09
RCA
05, 06
SAMSUNG
24
21, 22, 23
SHARP
27, 28
SHINTOM
30
SONY
18, 19, 20
ZENITH
08
Advertisement
Table of Contents
