H Troubleshooting - Panasonic KX-TG2302B Operating Instructions Manual

Things You Should Know

4-H Troubleshooting

Problem
• Check the settings (1-C).
The unit does not
• Check whether the dialing mode setting is
work.
correct (1-C).
• Fully charge the battery (4-A).
• Clean the charge contacts and charge again
(4-A).
• Check battery installation (1-C).
• Unplug the AC adaptor to reset it. Plug in,
and try again.
• Re-install the battery (1-C) and fully charge it.
• You are too far from the base unit. Walk closer
An alarm tone sounds
when you press [ ], to the base unit and try again.
• Confirm the AC adaptor is plugged in.
[SP-PHONE] or
• Raise the base unit antenna.
[VOICE ENHANCER].
• If the above remedies do not solve the
problem, the handset may have lost
communication with the base unit. Register the
handset again (3-E).
• Move the handset and the base unit away
Static, sound cuts
in/out, fades. from other electrical appliances (4-F).
• Walk closer to the base unit.
Interference from
• Raise the base unit antenna.
other electrical units.
• The ringer volume is turned off. Set to high,
The handset does not
ring. medium, or low (2-B).
• If the last number dialed was more than
You cannot redial.
48 digits long, the number will not be
redialed correctly.
• Please make sure you have long distance
You cannot make long
distance calls. service.
• The handset is too far from the base unit or
You cannot page the
handset. is engaged in an outside call. Try again later.
4-I Helpful Information
•
—
Environment do not place the unit in a room where the temperature is
less than 5˚C (41˚F) or greater than 40˚C (104˚F). Allow 10 cm (4")
clearance around the unit for proper ventilation. Avoid excessive smoke,
dust, mechanical vibration, shock, or direct sunlight.
•
Medical—consult the manufacturer of any personal medical devices, such
as pacemakers or hearing aids, to determine if they are adequately
shielded from external RF (radio frequency) energy. (The unit operates in
the frequency range of 2400MHz to 2481MHz, and the power output level
can range 0.04 to 0.1 watts.) Do not use the unit in health care facilities if
any regulations posted in the area instruct you not to do so. Hospitals or
health care facilities may be using equipment that could be sensitive to
external RF (radio frequency) energy.
•
Routine care—wipe the unit with a soft cloth. Do not use benzine, thinner,
or any abrasive powder. When you leave the unit unused for a long period
of time, unplug the AC adaptor from the outlet.
•
If there is any trouble—disconnect the unit from the telephone line and
connect a known working phone. If the known working phone operates
properly, have your unit repaired by one of the authorized Panasonic
Factory Service Centers. If the known working phone does not operate
properly, consult your telephone company.
Cause & Remedy
For assistance, please call: 1-800-211-PANA(7262)
Problem
• Set the flash time.
[FLASH/CALL WAIT]
does not work Press [VOICE ENHANCER], [9] and [8],
properly. then press [VOICE ENHANCER] again.
• Fully charge the battery (4-A).
The RECHARGE
indicator flashes or the
unit beeps
intermittently.
• Clean the charge contacts and charge again
You charged the
battery fully, but the (4-A).
• The battery may need to be replaced. If you
RECHARGE indicator
continues to flash. install a new battery, fully charge it (1-C).
• This is normal.
The CHARGE
indicator light does
not go out after the
battery has been
charged.
• Make sure the optional headset is connected
You cannot have a
conversation using properly (4-D).
• [SP-PHONE] may have been pressed. Press
the headset.
[
• Visit our website:
If you cannot solve
your problem http://www.panasonic.com/support
• Contact us via the web at:
http://www.panasonic.com/contactinfo
• Call our customer call center at:
1-800-211-PANA(7262)
For your future reference
Serial No.
(found on the bottom of the unit)
Name and address of dealer
Section 4
Cause & Remedy
] to switch to the headset.
Date of purchase