HIKVISION iDS-TCE507-BR Configuration Manual
  1. Manuals
  2. Brands
  3. HIKVISION Manuals
  4. Security Camera
  5. iDS-TCE507-BR
  6. Configuration manual

HIKVISION iDS-TCE507-BR Configuration Manual

Network traffic camera
Hide thumbs Also See for iDS-TCE507-BR:
Table of Contents

Advertisement

Quick Links

Download this manual
Network Traffic Camera
Configuration Manual

Advertisement

Table of Contents
loading

Related Manuals for HIKVISION iDS-TCE507-BR

Summary of Contents for HIKVISION iDS-TCE507-BR

  • Page 1 Network Traffic Camera Configuration Manual...
  • Page 2 With the philosophy of "Technology for the Good", Hikvision requests that every end user of video technology and video products shall comply with all the applicable laws and regulations, as well as ethical customs, aiming to jointly create a better community.
  • Page 3 Network Traffic Camera Configuration Manual control, selecting a suitable network environment (the Internet or Intranet) where video products are connected, establishing and constantly optimizing network security. Video products have made great contributions to the improvement of social security around the ●...
  • Page 4 WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES,...
  • Page 5 Network Traffic Camera Configuration Manual DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES.
  • Page 6 Network Traffic Camera Configuration Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Indicates a hazardous situation which, if not avoided, will or could Danger result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could Caution result in equipment damage, data loss, performance degradation, or...

  • Page 7: Table Of Contents

    Network Traffic Camera Configuration Manual Contents Chapter 1 Application Mode Configuration ................. 1 1.1 Set Checkpoint Capture ......................1 1.1.1 Set Checkpoint Single I/O ....................1 1.1.2 Set RS-485 Radar ......................4 1.1.3 Set Mixed-Traffic Lane ....................8 1.2 Set Intersection Violation System Capture ................12 1.3 Set Smart Monitoring Capture .....................
  • Page 8 Network Traffic Camera Configuration Manual 1.9.4 Set Picture Composition ....................47 1.9.5 Set Information Overlay ....................49 1.9.6 Set Body Picture Matting .................... 53 1.9.7 Set Traffic Light ......................54 1.9.8 Set Vehicle Feature Parameters .................. 57 1.9.9 Set Image Encoding Parameters .................. 58 1.9.10 Set Linked Capture ....................

  • Page 9: Chapter 1 Application Mode Configuration

    Network Traffic Camera Configuration Manual Chapter 1 Application Mode Configuration Note The supported application modes vary with different models. The actual device prevails. ● If the application mode supports area drawing, you can check Display All Areas to display all the ●...
  • Page 10 Network Traffic Camera Configuration Manual Figure 1-1 Set Checkpoint Single I/O 3. Optional: Select the violation type(s) to be detected, and set the corresponding parameters. Refer to Set Violation and Incident Detection for details. 4. Set scene and mode parameters. Refer to Set Scene Mode for details. 5.
  • Page 11 Network Traffic Camera Configuration Manual Capture is triggered according to the level signal status. If you select Falling Edge, the device will trigger capture at the moment that the high level falls to low level. If you select Rising Edge, the device will trigger capture at the moment that the low level rises to high level. Capture Interval Select Time, and set Interval (the time between the adjacent captures).

  • Page 12: Set Rs-485 Radar

    Network Traffic Camera Configuration Manual Figure 1-2 Draw Lane Line 12. Click Save. 1.1.2 Set RS-485 Radar Set RS-485 radar if RS-485 signal (speed detection or capture via radar) is connected, and capture is triggered by radar. In this mode, the information including the vehicle speed, vehicle passing time, vehicle overview, license plate number, license plate color, vehicle color, the facial features of the driver and the front passenger, etc.
  • Page 13 Network Traffic Camera Configuration Manual Steps 1. Go to Configuration → Capture → Application Mode . 2. Select Application Mode as RS-485 Radar.
  • Page 14 Network Traffic Camera Configuration Manual Figure 1-3 Set RS-485 Radar...
  • Page 15 Network Traffic Camera Configuration Manual 3. Optional: Select the violation type(s) to be detected, and set the corresponding parameters. Refer to Set Violation and Incident Detection for details. 4. Set scene and mode parameters. Refer to Set Scene Mode for details. 5.

  • Page 16: Set Mixed-Traffic Lane

    Network Traffic Camera Configuration Manual Figure 1-4 Draw Lane Line 12. Click Save. 1.1.3 Set Mixed-Traffic Lane Set mix-traffic lane if capture is triggered by virtual coils (video or radar detection). In this mode, the information including the vehicle speed, vehicle passing time, vehicle overview, license plate number, license plate color, vehicle color, the facial features of the driver and the front passenger, etc.
  • Page 17 Network Traffic Camera Configuration Manual Steps 1. Go to Configuration → Capture → Application Mode . 2. Select Application Mode as Mixed-Traffic Lane.
  • Page 18 Network Traffic Camera Configuration Manual Figure 1-5 Set Mixed-Traffic Lane...
  • Page 19 Network Traffic Camera Configuration Manual 3. Optional: Select the violation type(s) to be detected, and set the corresponding parameters. Refer to Set Violation and Incident Detection for details. 4. Set continuous capture parameters. Refer to Set Continuous Capture Parameters for details. 5.

  • Page 20: Set Intersection Violation System Capture

    Network Traffic Camera Configuration Manual Figure 1-6 Draw Lane Line 13. Click Save. 1.2 Set Intersection Violation System Capture Set video analysis intersection violation system if capture is triggered by virtual coils. In this mode, the information including the violation information, vehicle passing time, vehicle overview, license plate number, license plate color, vehicle color, etc.
  • Page 21 Network Traffic Camera Configuration Manual Figure 1-7 Set Intersection Violation System Capture...
  • Page 22 Network Traffic Camera Configuration Manual 3. Optional: Select the violation type(s) to be detected, and set the corresponding parameters. Refer to Set Violation and Incident Detection for details. 4. Set continuous capture parameters. Refer to Set Continuous Capture Parameters for details. 5.

  • Page 23: Set Smart Monitoring Capture

    Network Traffic Camera Configuration Manual Figure 1-8 Draw Lane Line 13. Click Save. 1.3 Set Smart Monitoring Capture The smart monitoring mode supports capturing motor vehicles, non-motor vehicles, and pedestrians via video triggering. Steps 1. Go to Configuration → Capture → Application Mode . 2.
  • Page 24 Network Traffic Camera Configuration Manual Figure 1-9 Set Smart Monitoring Capture 3. Set smart mode parameters. Capture Type Motor Vehicle, Non-Motor Vehicle, and Pedestrian The motor vehicles, non-motor vehicles, and pedestrians in the scene will be recognized and captured. Motor Vehicle and Non-Motor Vehicle The motor vehicles and non-motor vehicles in the scene will be recognized and captured.
  • Page 25 Network Traffic Camera Configuration Manual The number of captured picture(s). Capture Interval The time between the adjacent captures. 4. Set continuous capture parameters. Refer to Set Continuous Capture Parameters for details. 5. Set the lane parameters. Refer to Set Linked Lane Parameters for details. 6.

  • Page 26: Set License Plate Recognition System Capture

    Network Traffic Camera Configuration Manual Figure 1-10 Draw Lane Line 8. Click Save. 1.4 Set License Plate Recognition System Capture If you want to trigger capture of the passing vehicles and recognize the license plate numbers, set license plate recognition system capture. Steps 1.
  • Page 27 Network Traffic Camera Configuration Manual Figure 1-11 Set License Plate Recognition System 3. Select Trigger Type. Video Detection The passing vehicles will be recognized via videos. The capture mode is recommended as Strobe Light Mode. I/O Coil Select it when the device has been connected to I/O signal. Note The trigger types vary with different models.
  • Page 28 Network Traffic Camera Configuration Manual Scene Picture + Close-up Picture One passing vehicle picture and one close-up picture will be output. 5. Set the lane parameters. Refer to Set Linked Lane Parameters for details. 6. Set other parameters according to the selected trigger type. I/O Trigger Default Status Capture is triggered according to the level signal status.

  • Page 29: Set Data Collection

    Network Traffic Camera Configuration Manual Figure 1-12 Draw Lane Line 8. Click Save. 1.5 Set Data Collection The device supports to detect the traffic flow, POS, and other information. Steps 1. Go to Configuration → Capture → Application Mode . 2.
  • Page 30 Network Traffic Camera Configuration Manual Figure 1-13 Set Data Collection 4. Select the data upload mode. Upload Real-Time Data The device will upload the collected data to the server in real time. Upload Statistics Data The device will upload the collected data to the server according to the set interval. 5.
  • Page 31 Network Traffic Camera Configuration Manual 4) Enter Linked Lane No. 5) Select Direction and Lane Direction. 6) Optional: Check lane(s) to copy the parameters of the current lane to other lane(s). 8. Draw lane lines and virtual coil areas. 1) Click Draw Area. 2) Select the lane.

  • Page 32: Set Event Detection

    Network Traffic Camera Configuration Manual Figure 1-14 Draw Lane Lines 9. Click Save. 1.6 Set Event Detection The device supports to capture various traffic events. Steps 1. Go to Configuration → Capture → Application Mode . 2. Select Application Mode as Event Detection. 3.
  • Page 33 Network Traffic Camera Configuration Manual Figure 1-15 Set Event Detection 4. Set Scene Mode according to the actual conditions. 5. Set the capture parameters. Radar Track The radar track of the target will be overlaid on the captured pictures. Close Range Capture Check it and set Capture Interval.

  • Page 34: Set Application Mode Detailed Parameters

    Network Traffic Camera Configuration Manual 5) Optional: Click Draw Lane Line to restore to the default drawing. 6) Select area and click Draw Area. Click the left button of the mouse to draw a rectangular or polygonal frame, and then click the right button of the mouse to save the area. 7) Optional: Click Draw Area to delete the current area.
  • Page 35 Network Traffic Camera Configuration Manual Steps Note Not all the application modes support violation detection. ● The violation and incident detection types vary with different models. The actual device prevails. ● If the device supports setting associated masked area, you can check corresponding area and ●...
  • Page 36 Network Traffic Camera Configuration Manual Violation Detection Description Type Threshold and Actual Distance Between Measuring Lines according to the actual needs. Prohibition Violation Left-​ t urn violation, right-turn violation, emergency lane occupation, large-sized vehicle passing violation, bus lane occupation, etc. Check it and select the number of captured picture(s).
  • Page 37 Network Traffic Camera Configuration Manual Violation Detection Description Type always red during the process of turning left at the intersection, then the vehicle is judged as running the red light. Capture Position of First Picture: The vehicle position of the firstly ●...
  • Page 38 Network Traffic Camera Configuration Manual Violation Detection Description Type Sensitivity: The higher the sensitivity is, the more easily the violation ● will be captured. Number of Pedestrian Not Yielded to: When the number of ● pedestrians not yielded to reaches the set value, capture will be triggered.
  • Page 39 Network Traffic Camera Configuration Manual Violation Detection Description Type Roadblock Check it and set the corresponding parameters to detect the roadblock. Sensitivity: The higher the sensitivity is, the more easily the violation ● will be captured. Alarm Interval: The interval between two alarms. ●...

  • Page 40: Set Linked Lane Parameters

    Network Traffic Camera Configuration Manual Violation Detection Description Type Fire Check it and set the corresponding parameters to detect the fire on the lane. Sensitivity: The higher the sensitivity is, the more easily the event ● will be captured. Alarm Interval: The interval between two alarms. ●...

  • Page 41: Set Continuous Capture Parameters

    Network Traffic Camera Configuration Manual Linked Lane No. The corresponding lane No. linked with the current lane. The lane No. will be overlaid on the captured picture. Lane Type If you select Highway Emergency Lane or Truck Forbidden Lane, set the period. If you select Opposite Lane, the lane direction will be opposite from the current direction.

  • Page 42: Set Scene Mode

    Network Traffic Camera Configuration Manual Speeding Capture Check it to capture the speeding violation. One more picture will be captured beyond the set number of captured picture(s). Capture Interval Set Interval (dm) (the distance between the adjacent captures) if you select Distance, and set Capture Interval (ms) (the time between the adjacent captures) if you select Time.

  • Page 43: Calibrate Speed Via Video

    Network Traffic Camera Configuration Manual It adopts the frame extracting, and the captured pictures share the same exposure parameters with the video image. It is applicable to the condition of capturing license plates only. 5. Set Speed Detection Mode. Radar Speed detection via radar.

  • Page 44: Set Radar Parameters

    Network Traffic Camera Configuration Manual Note The number of vertexes should be consistent with the selected number of Calibration Point. 4) Drag the vertexes of the calibration area to align it to the lanes. Note If the lanes cannot be aligned, ensure the calibration area can contain the detection area. ●...

  • Page 45: Set Violation Recording Parameters

    Network Traffic Camera Configuration Manual 1. Go to Configuration → Capture → Application Mode . 2. Select Application Mode. 3. Set the parameters. Radar Type Select the connected radar type. Linkage RS-485 No. Select the connected RS-485 port No. of the radar. Radar Efficient Time If the duration from the time that the radar sends the detected vehicle speed to the device to the time that the device captures the vehicle locates in the efficient time, then the radar...

  • Page 46: Set Supplement Light Linkage

    Network Traffic Camera Configuration Manual Select the number of captured picture(s). Record will start after the set number of picture(s) captured. Pre-record Time The time before the violation recording starts. Post-record Time The time after the violation recording ends. 5. Click Save. 1.7.8 Set Supplement Light Linkage You can link supplement light(s) to the specific lane(s).

  • Page 47: Set Traffic Light Detection Parameters

    Network Traffic Camera Configuration Manual Steps Note Not all the application modes support lane speed limit parameters. ● The lane speed limit parameters vary with different models. The actual device prevails. ● 1. Go to Configuration → Capture → Application Mode . 2.
  • Page 48 Network Traffic Camera Configuration Manual Steps 1. Go to Configuration → Capture → Application Mode . 2. Select Application Mode as Video Analysis E-Police. 3. Select Traffic Light Signal Input and set the corresponding parameters. RS-485 Set Linked Red Light Channel and Yellow Light Related Channel No. according to the actual wiring.

  • Page 49: Set Capture Schedule

    Network Traffic Camera Configuration Manual Network Set Linked Red Light Channel and Yellow Light Related Channel No. according to Mode the actual wiring. Note You can go to Live View → Traffic Light Status to view the traffic light status. 4.

  • Page 50: Set Capture Parameters

    Network Traffic Camera Configuration Manual Figure 1-19 Set Capture Schedule 4. Select Lane. 5. Optional: Check No Plate Vehicle Capture according to the actual needs. 6. Adjust the time period. - Click on the selected time period, and enter the desired value. Click Save. - Click on the selected time period.
  • Page 51 Network Traffic Camera Configuration Manual Steps Note The function varies with different models. The actual device prevails. 1. Go to Configuration → Capture → Capture Images → Image Parameters . Figure 1-20 Set Captured Image Parameters 2. Set the captured image parameters. Brightness It refers to the max.

  • Page 52: Set License Plate Recognition Parameters

    Network Traffic Camera Configuration Manual Window Enhancement. The higher the Brightness Enhancement Level is, the brighter the window image is. The higher the Defog Level is, the better the permeability of the window image is. White Balance Level It is the white rendition function of the device used to adjust the color temperature according to the environment.

  • Page 53: Set Supplement Light Parameters

    Network Traffic Camera Configuration Manual Figure 1-21 Set License Plate Recognition Parameters 2. Set Country/Region according to the actual needs. 3. Select License Plate Recognition. - Select Forward when license plates of vehicles from the approaching direction need to be recognized.
  • Page 54 Network Traffic Camera Configuration Manual Figure 1-22 Set Supplement Light Parameters 2. Select the I/O and set the supplement light parameters. I/O Output Mode Supplement Light Mode The flash light will be triggered by the signals and output high intensity illumination instantaneously.

  • Page 55: Set Picture Composition

    Network Traffic Camera Configuration Manual The effective status should stay different with the default status for I/O to take effect. And the default status changes according to the selection of the effective status. If you set the effective status as high level, the default level goes to low level. Pulse When pulse signal is output to the supplement light, the light will flash.
  • Page 56 Network Traffic Camera Configuration Manual 1. Go to Configuration → Capture → Capture Parameters → Image Encoding and Composition → Image Composition/Violation Picture Composition . Figure 1-23 Set Picture Composition 2. Check Enable Composition. 3. Set composition types for different picture quantities. 4.

  • Page 57: Set Information Overlay

    Network Traffic Camera Configuration Manual 1.9.5 Set Information Overlay Set Single Picture Overlay If you want to overlay information on the captured single pictures, set capture overlay. Steps Note The supported parameters vary with different models. The actual device prevails. 1.
  • Page 58 Network Traffic Camera Configuration Manual When the overlaid number digits are smaller than the fixed digits, 0 will be overlaid before the overlaid number. E.g., the fixed digits for lane No. is 2. If the lane No. is 1, 01 will be overlaid on the picture.
  • Page 59 Network Traffic Camera Configuration Manual Figure 1-25 Set Composite Picture Overlay 4. Set the font size, color, overlay position, etc. Percentage It is the percentage that the overlaid information occupies on the picture. For example, if you set the percentage to 50, the overlaid information in a row will occupy up to half of the image width, and the excess content will be overlaid from a new line.
  • Page 60 Network Traffic Camera Configuration Manual Set Line Break Edit the number of characters from 0 to 100 between the current Characters information line and the previous information line. 0 means no line break. Adjust overlay Click to adjust the display sequence of the overlay sequence information.

  • Page 61: Set Body Picture Matting

    Network Traffic Camera Configuration Manual Check Face Picture Matting of Violation Picture to detect the passenger's face in the ● violation picture. Check Check out Front Passenger Forcedly to mat the front passenger's picture no ● matter there is someone in the seat or not. Non-Motor Vehicle User's Face Picture Matting Check it when you need to detect the non-motor vehicle user's face picture.

  • Page 62: Set Traffic Light

    Network Traffic Camera Configuration Manual Steps Note The function varies with different models. The actual device prevails. 1. Go to Configuration → Capture → Capture Parameters → Vehicle Feature → Body Picture Matting . 2. Check Enable Body Picture Matting. Figure 1-27 Set Body Picture Matting 3.
  • Page 63 Network Traffic Camera Configuration Manual Figure 1-28 Set Traffic Light Enhancement 3. Select Enhancement Mode. Note Select Smart Traffic Light Enhancement if the device supports this mode. 4. Draw traffic light areas. 1) Select Magnification. 2) Click Zoom In. 3) Click Add Traffic Light. 4) Adjust the drawn areas according to the actual scene.
  • Page 64 Network Traffic Camera Configuration Manual 5) Optional: Select Light Shape. 6) Optional: Set Yellow Light Delay Time. 5. Set traffic light enhancement parameters according to the actual needs. Note Keep default settings if the device supports smart traffic light enhancement mode. Correction Level You can set different correction levels for different periods.

  • Page 65: Set Vehicle Feature Parameters

    Network Traffic Camera Configuration Manual Figure 1-30 Set Traffic Light Synchronization 3. Set Phase Position and Signal Frequency according to the actual needs. 4. Click Save. 1.9.8 Set Vehicle Feature Parameters Set vehicle feature parameters if you need to detect the vehicle features of the passing vehicle. Steps Note The parameters vary with different models.

  • Page 66: Set Image Encoding Parameters

    Network Traffic Camera Configuration Manual 1.9.9 Set Image Encoding Parameters If the captured pictures are not clear, set the resolution of the captured pictures and the picture size. Steps 1. Go to Configuration → Capture → Capture Parameters → Image Encoding and Composition → Image Encoding .

  • Page 67: Set Barrier Gate Linkage

    Network Traffic Camera Configuration Manual Steps Note The function varies with different models. The actual device prevails. 1. Go to Configuration → Event → Alarm Linkage → Linked Capture . 2. Check Enable. Figure 1-33 Set Linked Capture 3. Check Linkage Type. Note The supported linkage types vary with different violation types.

  • Page 68: Set Allowlist And Blocklist

    Network Traffic Camera Configuration Manual 1.10.1 Set Allowlist and Blocklist Set allowlist and blocklist if you want to control the passing vehicles at the entrance or exit via the barrier gate. Before You Start Connect the barrier gate to the relay output interface of the device. ●...

  • Page 69: Control Barrier Gate

    Network Traffic Camera Configuration Manual Delete Select the delete type, or enter the keywords. Click Delete to delete the lists of ● the same type. Select an item from the list, and click to delete the item. ● Click Delete All to delete all the lists. ●...

  • Page 70: Set Wiegand Parameters

    Network Traffic Camera Configuration Manual Note The supported number of relays varies with different models. Relay 1 corresponds to the 1A and 1B of the terminal. Relay 2 corresponds to the 2A and 2B of the terminal. 4. Set the barrier gate operation and alarm operation for the temporary vehicles, vehicles in the blocklist, and vehicles in the allowlist.

  • Page 71: Chapter 2 Radar Detection

    Network Traffic Camera Configuration Manual Chapter 2 Radar Detection Radar is used to detect the target and link the capture. Set radar detection parameters before capturing vehicle pictures. Note The function varies with different models. The actual device prevails. 2.1 Set Detection Parameters Set radar detection parameters before capturing vehicle pictures.
  • Page 72 Network Traffic Camera Configuration Manual 1) Set Number of Lane and the width of each lane. Note The number of lanes is consistent with the total lanes in the application mode settings. 2) Set Scene Mode. 3) Set Vehicle Direction. Approaching Direction The vehicles are driven towards the construction position of the camera.
  • Page 73 Network Traffic Camera Configuration Manual Enable the function, and the target track will be displayed on the interface according to the detected coordinates. Advanced Settings Debug Mode Enable the radar debugging mode. In this mode, the vehicles outside the drawn area will be displayed, to make it convenient to debug the radar.

  • Page 74: Set Radar Calibration

    Network Traffic Camera Configuration Manual Adjust the course angle of the radar for target detection. Auto Angle Correction Check it to get the radar deviation angle according to the moving path of vehicle. 6. Click Save. 2.2 Set Radar Calibration Calibrate radar after the radar detection parameters are set to display the targets detected by the radar on the video.
  • Page 75 Network Traffic Camera Configuration Manual Figure 2-2 Manual Calibration 3. Draw the lane lines. 1) Select the lane sum. 2) Select the lane line No. 3) Click Draw Lane Line. The selected lane line will be displayed on the live view picture. 4) Drag the two end points of the line or drag the whole line to adjust its position according to the actual scene.

  • Page 76: Auto Calibration

    Network Traffic Camera Configuration Manual Note The origin (0, 0) of the world coordinates locates in the middle of the whole lanes detected by the radar. You can refer to the top view of the diagram for the positions. 6. Adjust the radar in two ways if the coordinates fed back from the radar cannot be matched with the measured coordinates when the vehicle passes the calibration position.

  • Page 77: Gps Calibration

    Network Traffic Camera Configuration Manual 4) Drag the two end points of the line or drag the whole line to adjust its position according to the actual scene. 5) Repeat the steps above to draw more lane lines. 4. Click Start. The auto calibration starts, and you can view the calibration status and progress.

  • Page 78: Search Detected Vehicles

    Network Traffic Camera Configuration Manual 4. Click OK. 2.3 Search Detected Vehicles You can search the radar detected vehicles and export the information. Steps 1. Click Radar. 2. View the vehicle information in the vehicle list. 3. Enter the vehicle No. in the text field, and press Enter to search the vehicle information. 4.

  • Page 79: Chapter 3 View Real-Time Picture

    Network Traffic Camera Configuration Manual Chapter 3 View Real-Time Picture You can view the real-time captured pictures and license plate information. Steps Note The supported parameters vary with different models. The actual device prevails. 1. Go to Live View → Real-Time Capture . 2.
  • Page 80 Network Traffic Camera Configuration Manual Click it to measure the license plate pixel. Click it again to disable the measurement. Click it to enable the ruler to measure the license plate. Click it to enable manual capture. Click it to set continuous capture parameters and the device will capture pictures according to the set interval.

  • Page 81: Chapter 4 Search Picture

    Network Traffic Camera Configuration Manual Chapter 4 Search Picture You can search the captured pictures stored in the storage card and export the pictures you need. Before You Start Install the storage card, and ensure the storage status is normal. Steps 1.

  • Page 82: Chapter 5 View Traffic Statistics

    Network Traffic Camera Configuration Manual Chapter 5 View Traffic Statistics 5.1 View Real-Time Traffic Statistics You can view the real-time traffic statistics if the device supports this function. Steps Note This function varies with different models. The actual device prevails. 1.

  • Page 83: Chapter 6 View Traffic Light Status

    Network Traffic Camera Configuration Manual Chapter 6 View Traffic Light Status For the device supporting traffic light detection, you can go to Live View → Traffic Light Status to check real-time traffic light status after the traffic light detection mode is set.
  • Page 84 UD31785B...

This manual is also suitable for:

Ids-2cd9396-bisIds-tcs800-ciIds-2cd9856-bisIds-tce500-bIds-tce907-brIds-tce900-b ... Show all

Table of Contents