HIKVISION iDS-TCV507-BIR/1550 Configuration Manual
  1. Manuals
  2. Brands
  3. HIKVISION Manuals
  4. Security Camera
  5. iDS-TCV507-BIR/1550
  6. Configuration manual

HIKVISION iDS-TCV507-BIR/1550 Configuration Manual

Network traffic camera
Hide thumbs Also See for iDS-TCV507-BIR/1550:
Table of Contents

Advertisement

Quick Links

Download this manual
Network Traffic Camera
Configuration Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the iDS-TCV507-BIR/1550 and is the answer not in the manual?

Questions and answers

Related Manuals for HIKVISION iDS-TCV507-BIR/1550

Summary of Contents for HIKVISION iDS-TCV507-BIR/1550

  • Page 1 Network Traffic Camera Configuration Manual...
  • Page 2 With the philosophy of "Technology for the Good", Hikvision requests that every end user of video technology and video products shall comply with all the applicable laws and regulations, as well as ethical customs, aiming to jointly create a better community.
  • Page 3 Network Traffic Camera Configuration Manual control, selecting a suitable network environment (the Internet or Intranet) where video products are connected, establishing and constantly optimizing network security. Video products have made great contributions to the improvement of social security around the ●...
  • Page 4 WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES,...
  • Page 5 Network Traffic Camera Configuration Manual DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES.
  • Page 6 Network Traffic Camera Configuration Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Indicates a hazardous situation which, if not avoided, will or could Danger result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could Caution result in equipment damage, data loss, performance degradation, or...

  • Page 7: Table Of Contents

    Network Traffic Camera Configuration Manual Contents Chapter 1 Application Mode Configuration ................. 1 1.1 Set Checkpoint Capture ......................1 1.1.1 Set Checkpoint Single I/O ....................1 1.1.2 Set RS-485 Radar ......................4 1.1.3 Set Mixed-Traffic Lane ....................8 1.2 Set Intersection Violation System Capture ................12 1.3 Set Smart Monitoring Capture .....................
  • Page 8 Network Traffic Camera Configuration Manual 1.7.6 Set Body Picture Matting .................... 44 1.7.7 Set Traffic Light ......................45 1.7.8 Set Vehicle Feature Parameters .................. 48 1.7.9 Set Image Encoding Parameters .................. 49 1.8 Set Barrier Gate Linkage ....................... 49 1.8.1 Set Allowlist and Blocklist ................... 50 1.8.2 Control Barrier Gate ....................

  • Page 9: Chapter 1 Application Mode Configuration

    Network Traffic Camera Configuration Manual Chapter 1 Application Mode Configuration Note The supported application modes vary with different models. The actual device prevails. ● If the application mode supports area drawing, you can check Display All Areas to display all the ●...
  • Page 10 Network Traffic Camera Configuration Manual Figure 1-1 Set Checkpoint Single I/O 3. Optional: Select the violation type(s) to be detected, and set the corresponding parameters. Refer to Set Violation and Incident Detection for details. 4. Set scene and mode parameters. Refer to Set Scene Mode for details. 5.
  • Page 11 Network Traffic Camera Configuration Manual Capture is triggered according to the level signal status. If you select Falling Edge, the device will trigger capture at the moment that the high level falls to low level. If you select Rising Edge, the device will trigger capture at the moment that the low level rises to high level. Capture Interval Select Time, and set Interval (the time between the adjacent captures).

  • Page 12: Set Rs-485 Radar

    Network Traffic Camera Configuration Manual Figure 1-2 Draw Lane Line 12. Click Save. 1.1.2 Set RS-485 Radar Set RS-485 radar if RS-485 signal (speed detection or capture via radar) is connected, and capture is triggered by radar. In this mode, the information including the vehicle speed, vehicle passing time, vehicle overview, license plate number, license plate color, vehicle color, the facial features of the driver and the front passenger, etc.
  • Page 13 Network Traffic Camera Configuration Manual Steps 1. Go to Configuration → Capture → Application Mode . 2. Select Trigger Mode as RS-485 Radar.
  • Page 14 Network Traffic Camera Configuration Manual Figure 1-3 Set RS-485 Radar...
  • Page 15 Network Traffic Camera Configuration Manual 3. Optional: Select the violation type(s) to be detected, and set the corresponding parameters. Refer to Set Violation and Incident Detection for details. 4. Set scene and mode parameters. Refer to Set Scene Mode for details. 5.

  • Page 16: Set Mixed-Traffic Lane

    Network Traffic Camera Configuration Manual Figure 1-4 Draw Lane Line 12. Click Save. 1.1.3 Set Mixed-Traffic Lane Set mix-traffic lane if capture is triggered by virtual coils (video or radar detection). In this mode, the information including the vehicle speed, vehicle passing time, vehicle overview, license plate number, license plate color, vehicle color, the facial features of the driver and the front passenger, etc.
  • Page 17 Network Traffic Camera Configuration Manual Steps 1. Go to Configuration → Capture → Application Mode . 2. Select Trigger Mode as Mixed-Traffic Lane.
  • Page 18 Network Traffic Camera Configuration Manual Figure 1-5 Set Mixed-Traffic Lane...
  • Page 19 Network Traffic Camera Configuration Manual 3. Optional: Select the violation type(s) to be detected, and set the corresponding parameters. Refer to Set Violation and Incident Detection for details. 4. Set continuous capture parameters. Refer to Set Continuous Capture Parameters for details. 5.

  • Page 20: Set Intersection Violation System Capture

    Network Traffic Camera Configuration Manual Figure 1-6 Draw Lane Line 13. Click Save. 1.2 Set Intersection Violation System Capture Set video analysis intersection violation system if capture is triggered by virtual coils. In this mode, the information including the violation information, vehicle passing time, vehicle overview, license plate number, license plate color, vehicle color, etc.
  • Page 21 Network Traffic Camera Configuration Manual Figure 1-7 Set Intersection Violation System Capture...
  • Page 22 Network Traffic Camera Configuration Manual 3. Optional: Select the violation type(s) to be detected, and set the corresponding parameters. Refer to Set Violation and Incident Detection for details. 4. Set continuous capture parameters. Refer to Set Continuous Capture Parameters for details. 5.

  • Page 23: Set Smart Monitoring Capture

    Network Traffic Camera Configuration Manual Figure 1-8 Draw Lane Line 13. Click Save. 1.3 Set Smart Monitoring Capture The smart monitoring mode supports capturing motor vehicles, non-motor vehicles, and pedestrians via video triggering. Steps 1. Go to Configuration → Capture → Application Mode . 2.
  • Page 24 Network Traffic Camera Configuration Manual Figure 1-9 Set Smart Monitoring Capture 3. Set smart mode parameters. Capture Type Motor Vehicle, Non-Motor Vehicle, and Pedestrian The motor vehicles, non-motor vehicles, and pedestrians in the scene will be recognized and captured. Motor Vehicle Only the motor vehicles in the scene will be recognized and captured.
  • Page 25 Network Traffic Camera Configuration Manual 4. Set continuous capture parameters. Refer to Set Continuous Capture Parameters for details. 5. Set the lane parameters. Refer to Set Linked Lane Parameters for details. 6. Optional: Check the other lane(s) to copy the same settings. 7.

  • Page 26: Set License Plate Recognition System Capture

    Network Traffic Camera Configuration Manual 8. Click Save. 1.4 Set License Plate Recognition System Capture If you want to trigger capture of the passing vehicles and recognize the license plate numbers, set license plate recognition system capture. Steps 1. Go to Configuration → Capture → Application Mode . 2.
  • Page 27 Network Traffic Camera Configuration Manual Select it when the device has been connected to I/O signal. Note The trigger types vary with different models. The actual device prevails. 4. Select Picture Type. Scene Picture Only one passing vehicle picture will be output. Scene Picture + Close-up Picture One passing vehicle picture and one close-up picture will be output.

  • Page 28: Set Application Mode Detailed Parameters

    Network Traffic Camera Configuration Manual Figure 1-12 Draw Lane Line 8. Click Save. 1.5 Set Application Mode Detailed Parameters 1.5.1 Set Violation and Incident Detection The device supports different violation types detection. You can select the violation type(s) to be detected under different application modes, and set the corresponding parameters.
  • Page 29 Network Traffic Camera Configuration Manual Steps Note Not all the application modes support violation detection. ● The violation and incident detection types vary with different models. The actual device prevails. ● 1. Go to Configuration → Capture → Application Mode . 2.
  • Page 30 Network Traffic Camera Configuration Manual Violation Detection Description Type Note If Prohibition Violation is enabled, and Lane Type is set as Highway Emergency Lane, the violation of occupying emergency lane will be captured. Not Following The moving direction of the motor vehicle is not consistent with the Directional Sign guidance direction at the intersection.
  • Page 31 Network Traffic Camera Configuration Manual Violation Detection Description Type Distance to Stop Line: The offset pixel of the second captured ● picture of the vehicle running the red light to the stop line. Offset for Third Capture: The min. offset pixel of the third captured ●...

  • Page 32: Set Linked Lane Parameters

    Network Traffic Camera Configuration Manual Violation Detection Description Type Capture Position Control Ratio: When the length of the target ● vehicle body beyond the stop line exceeds the ratio, the vehicle is regarded as failing to yield for pedestrians, and capture will be triggered.

  • Page 33: Set Continuous Capture Parameters

    Network Traffic Camera Configuration Manual If you select Opposite Lane, the lane direction will be opposite from the current direction. Total Lanes The sum of the linked lane(s) under the current application mode. Lane Direction The guidance direction of the lane. Lane Property Select the lane type for speeding capture.

  • Page 34: Set Scene Mode

    Network Traffic Camera Configuration Manual 4. Click Save. 1.5.4 Set Scene Mode Set the capture type, capture mode, and speed detection mode for the application mode. Steps Note Not all the application modes support scene mode settings. ● The scene mode parameters vary with different models. The actual device prevails. ●...

  • Page 35: Calibrate Speed Via Video

    Network Traffic Camera Configuration Manual 6. Click Save. 1.5.5 Calibrate Speed via Video In mixed-traffic lane mode, if you select speed detection mode as video, you need to calibrate speed via video. Before You Start In mixed-traffic lane mode, select Speed Detection Mode as Video. Steps 1.

  • Page 36: Set Radar Parameters

    Network Traffic Camera Configuration Manual Note If the lanes cannot be aligned, ensure the calibration area can contain the detection area. ● You can refer to the schematic diagram and top view description to draw the calibration ● area. 5) Optional: Click Clear to clear the drawn calibration area. 3.

  • Page 37: Set Violation Recording Parameters

    Network Traffic Camera Configuration Manual Select the connected radar type. Linkage RS-485 No. Select the connected RS-485 port No. of the radar. Radar Efficient Time If the duration from the time that the radar sends the detected vehicle speed to the device to the time that the device captures the vehicle locates in the efficient time, then the radar detected speed is valid.

  • Page 38: Set Supplement Light Linkage

    Network Traffic Camera Configuration Manual Post-record Time The time after the violation recording ends. 5. Click Save. 1.5.8 Set Supplement Light Linkage You can link supplement light(s) to the specific lane(s). Before You Start Connect the supplement light(s) to the corresponding interface(s) of the device. Steps Note Not all the application modes support supplement light linkage.

  • Page 39: Set Traffic Light Detection Parameters

    Network Traffic Camera Configuration Manual 2. Select Trigger Mode. 3. Set the lane speed limit parameters for small-sized and large-sized vehicles. Abnormal Low Speed When the detected speed of the vehicle is lower than the value, the detection is regarded as abnormal, and a normal speed will be provided randomly.
  • Page 40 Network Traffic Camera Configuration Manual Video Click Set to set the video analysis area. Analysis Interface Figure 1-14 Set Video Analysis Area a. Select the area. b. Set the parameters. - Guiding Direction of Traffic Light: The direction guided by the traffic light. - Traffic Light Color: The color of the traffic light.

  • Page 41: Set Capture Schedule

    Network Traffic Camera Configuration Manual 1.6 Set Capture Schedule You can set the schedule for the violation behavior capture or checkpoint capture if needed. Steps Note The function varies with different models. The actual device prevails. 1. Go to Configuration → Capture → Capture Parameters → Capture Schedule . 2.

  • Page 42: Set Capture Parameters

    Network Traffic Camera Configuration Manual - Click on the selected time period, and enter the desired value. Click Save. - Click on the selected time period. Drag the both ends to adjust the time period. 7. Optional: Click to copy the same settings to other days. 8.
  • Page 43 Network Traffic Camera Configuration Manual Shutter If the shutter speed is quick, the details of the moving objects can be displayed better. If the shutter speed is slow, the outline of the moving objects will be fuzzy and trailing will appear. Gain It refers to the upper limit value of limiting image signal amplification.

  • Page 44: Set License Plate Recognition Parameters

    Network Traffic Camera Configuration Manual 1.7.2 Set License Plate Recognition Parameters When there are vehicles of different types passing from different directions, set the license plate recognition parameters. Before You Start For some models, you need to select Trigger Mode as License Plate Recognition System. Steps Note The supported parameters vary with different models.
  • Page 45 Network Traffic Camera Configuration Manual Steps Note For video intersection violation system mode, only strobe light can be connected, and the I/O ● effective status should be set as pulse. The supported parameters vary with different models. The actual device prevails. ●...
  • Page 46 Network Traffic Camera Configuration Manual It is the dwell time [0 to 10000 μs] after the flash light responds. The actual flash light supplement time is the result of the dwell time minus advanced time. Effective Status Select the effective status of the supplement light according to the actual condition. High/Low When high/low level signal is output to the supplement light, the light will flash.

  • Page 47: Set Picture Composition

    Network Traffic Camera Configuration Manual 1.7.4 Set Picture Composition You can enable the picture composition to composite several pictures into one to make it convenient to view the violation captured pictures. Steps Note Functions and parameters vary with different models. The actual device prevails. 1.

  • Page 48: Set Information Overlay

    Network Traffic Camera Configuration Manual Note Enabling composition and outputting close-up independently functions conflict with each other. You can only enable one. 6. Click Save. 1.7.5 Set Information Overlay Set Single Picture Overlay If you want to overlay information on the captured single pictures, set capture overlay. Steps Note The supported parameters vary with different models.
  • Page 49 Network Traffic Camera Configuration Manual Transparency It is the condition of viewing the live view image through the overlaid information. Overlay Number Zeroizing When the overlaid number digits are smaller than the fixed digits, 0 will be overlaid before the overlaid number. E.g., the fixed digits for lane No. is 2. If the lane No. is 1, 01 will be overlaid on the picture.
  • Page 50 Network Traffic Camera Configuration Manual 1. Go to Configuration → Capture → Capture Parameters → Text Overlay . 2. Select composite picture channel. 3. Check Capture Picture Overlay. Figure 1-21 Set Composite Picture Overlay 4. Set the font size, color, overlay position, etc. Percentage It is the percentage that the overlaid information occupies on the picture.
  • Page 51 Network Traffic Camera Configuration Manual Set Space Edit the number of space between the current information and the next one from 0 to 255. 0 means there is no space. Set Line Break Edit the number of characters from 0 to 100 between the current Characters information line and the previous information line.

  • Page 52: Set Body Picture Matting

    Network Traffic Camera Configuration Manual Check it when you need to detect the passenger's face picture. Check Face Picture Matting of Violation Picture to detect the passenger's face in the ● violation picture. Check Check out Front Passenger Forcedly to mat the front passenger's picture no ●...

  • Page 53: Set Traffic Light

    Network Traffic Camera Configuration Manual Steps Note The function varies with different models. The actual device prevails. 1. Go to Configuration → Capture → Capture Parameters → Vehicle Feature → Body Picture Matting . 2. Check Enable Body Picture Matting. Figure 1-23 Set Body Picture Matting 3.
  • Page 54 Network Traffic Camera Configuration Manual Figure 1-24 Set Traffic Light Enhancement 3. Select Enhancement Mode. Note Select Smart Traffic Light Enhancement if the device supports this mode. 4. Draw traffic light areas. 1) Select Magnification. 2) Click Zoom In. 3) Click Add Traffic Light. 4) Adjust the drawn areas according to the actual scene.
  • Page 55 Network Traffic Camera Configuration Manual 5) Optional: Select Light Shape. 6) Optional: Set Yellow Light Delay Time. 5. Set traffic light enhancement parameters according to the actual needs. Note Keep default settings if the device supports smart traffic light enhancement mode. Correction Level You can set different correction levels for different periods.

  • Page 56: Set Vehicle Feature Parameters

    Network Traffic Camera Configuration Manual Figure 1-26 Set Traffic Light Synchronization 3. Set Phase Position and Signal Frequency according to the actual needs. 4. Click Save. 1.7.8 Set Vehicle Feature Parameters Set vehicle feature parameters if you need to detect the vehicle features of the passing vehicle. Steps Note The parameters vary with different models.

  • Page 57: Set Image Encoding Parameters

    Network Traffic Camera Configuration Manual 1.7.9 Set Image Encoding Parameters If the captured pictures are not clear, set the resolution of the captured pictures and the picture size. Steps 1. Go to Configuration → Capture → Capture Parameters → Picture Encoding and Composition → Image Encoding .

  • Page 58: Set Allowlist And Blocklist

    Network Traffic Camera Configuration Manual 1.8.1 Set Allowlist and Blocklist Set allowlist and blocklist if you want to control the passing vehicles at the entrance or exit via the barrier gate. Before You Start Connect the barrier gate to the relay output interface of the device. ●...

  • Page 59: Control Barrier Gate

    Network Traffic Camera Configuration Manual Delete Select the delete type, or enter the keywords. Click Delete to delete the lists of ● the same type. Select an item from the list, and click to delete the item. ● Click Delete All to delete all the lists. ●...

  • Page 60: Set Wiegand Parameters

    Network Traffic Camera Configuration Manual Note The supported number of relays varies with different models. Relay 1 corresponds to the 1A and 1B of the terminal. Relay 2 corresponds to the 2A and 2B of the terminal. 4. Set the barrier gate operation and alarm operation for the temporary vehicles, vehicles in the blocklist, and vehicles in the allowlist.

  • Page 61: Chapter 2 Radar Detection

    Network Traffic Camera Configuration Manual Chapter 2 Radar Detection Radar is used to detect the target and link the capture. Set radar detection parameters before capturing vehicle pictures. Note The function varies with different models. The actual device prevails. 2.1 Set Detection Parameters Set radar detection parameters before capturing vehicle pictures.
  • Page 62 Network Traffic Camera Configuration Manual Construction Height Set the construction height of the radar according to construction at the actual scene. Display Track Enable the function, and the target track will be displayed on the interface according to the detected coordinates. Angle Deviation Set the angle compensation according to the target moving track detected by the radar.

  • Page 63: Set Radar Calibration

    Network Traffic Camera Configuration Manual initial position of the target should be approximately 35 m. The target track should correspond to the actual lane, or the lane No. cannot be corresponded to when the data is uploaded. Adjust Angle Deviation and Horizontal Deviation to guarantee the vehicle target is on the corresponding lane.

  • Page 64: Manual Calibration

    Network Traffic Camera Configuration Manual Steps 1. Click Radar. 2. Click Coordinate Calibration. 3. Set the radar calibration. - Set manual calibration. Refer to Manual Calibration for details. - Set auto calibration. Refer to Auto Calibration for details. Note The supported calibration modes vary with different models. The actual device prevails. 2.2.1 Manual Calibration Steps 1.

  • Page 65: Auto Calibration

    Network Traffic Camera Configuration Manual 2) Click Calibration. 3) Click the left button of the mouse to locate the vertexes of the calibration area on the live view image, and click the right button of the mouse to finish the drawing. Note The number of vertexes should be consistent with the selected number of Calibration Point.

  • Page 66: Search Detected Vehicles

    Network Traffic Camera Configuration Manual Figure 2-4 Auto Calibration 3. Draw the lane lines. 1) Select the lane sum. 2) Select the lane line No. 3) Click Draw Lane Line. The selected lane line will be displayed on the live view picture. 4) Drag the two end points of the line or drag the whole line to adjust its position according to the actual scene.
  • Page 67 Network Traffic Camera Configuration Manual - Search the vehicle first, and click Export to export the searched vehicle information to the computer. - Click Export directly to export the information of all the detected vehicles to the computer.

  • Page 68: Chapter 3 View Real-Time Picture

    Network Traffic Camera Configuration Manual Chapter 3 View Real-Time Picture You can view the real-time captured pictures and license plate information. Steps 1. Go to Live View → Real-Time Capture . 2. Click Arming. 3. Select an item from the list, and you can view the capture scene picture and recognized license plate information.
  • Page 69 Network Traffic Camera Configuration Manual Click it to enable the ruler to measure the license plate. Click it to enable manual capture. Click it to set continuous capture parameters and the device will capture pictures according to the set interval. Capture Times: Up to five pictures can be captured per continuous capture.

  • Page 70: Chapter 4 Search Picture

    Network Traffic Camera Configuration Manual Chapter 4 Search Picture You can search the captured pictures stored in the storage card and export the pictures you need. Before You Start Install the storage card, and ensure the storage status is normal. Steps 1.

  • Page 71: Chapter 5 View Traffic Statistics

    Network Traffic Camera Configuration Manual Chapter 5 View Traffic Statistics 5.1 View Real-Time Traffic Statistics You can view the real-time traffic statistics if the device supports this function. Steps 1. Go to Configuration → Capture → Advanced → Traffic Parameters → Traffic Parameters . 2.

  • Page 72: Chapter 6 View Traffic Light Status

    Network Traffic Camera Configuration Manual Chapter 6 View Traffic Light Status For the device supporting traffic light detection, you can go to Live View → Traffic Light Status to check real-time traffic light status after the traffic light detection mode is set.
  • Page 73 UD29407B...

This manual is also suitable for:

Ids-tcv507-ber/1550Ids-tce900-b/1140/h1Ids-tce900-b/1140Ids-tce500-b/1550/h1Ids-tce500-b/1550Ids-tce907-br/1140 ... Show all

Table of Contents