Dake JH-10 Operator's Manual
  1. Manuals
  2. Brands
  3. Dake Manuals
  4. Saw
  5. JH-10
  6. Operator's manual

Dake JH-10 Operator's Manual

Horizontal bandsaw
Hide thumbs Also See for JH-10:
Table of Contents

Advertisement

Quick Links

Download this manual
Operator's Manual and Part's List
Model J-10 & JH-10
Dake/Johnson Horizontal Bandsaw
DAKE Division of JSJ
724 Robbins Road
Grand Haven, MI 49417
Phone: 1-800-937-3253
Fax:
1-800-846-3253
E-mail:
customerservice@dakecorp.com
technicalservice@dakecorp.com
Web:
www.dakecorp.com
616-842-7110
616-842-0859
6/02
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the JH-10 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Dake JH-10

Summary of Contents for Dake JH-10

  • Page 1 6/02 Operator’s Manual and Part’s List Model J-10 & JH-10 Dake/Johnson Horizontal Bandsaw DAKE Division of JSJ 724 Robbins Road Grand Haven, MI 49417 Phone: 1-800-937-3253 616-842-7110 Fax: 1-800-846-3253 616-842-0859 E-mail: customerservice@dakecorp.com technicalservice@dakecorp.com Web: www.dakecorp.com...
  • Page 2 Please refer to the pertinent sections when contacting the factory regarding parts, schematics…or when you have other questions. As Dake’s policy is one of continuous development for each range of machine, the contents of this manual, though completely up to date when issued, are subject to change without notice.

  • Page 3: Table Of Contents

    6/02 CONTENTS GENERAL Basic Machine Data ……………………………………. Specifications …………………………………………….. Machine Installation ……………………………………… Safety Information………………………………………… Electrical Diagrams ………………………………………. Machine Features ……………………………………….. SECTION 1 OPERATION Controls and Operation ………………………………….. Standard Drive …………………………………………… Blade Selection ………………………………………….. Blade Removal/Installation ……………………………… 13-14 Blade Guide Adjustment ………………………………… 14-15 Balance Spring Adjustment ……………………………..
  • Page 4 ………………………………..15, 29, 49 and 82 mpm J-10 Wet ..……………………….. 845 lbs (383 kgs) Bed Work Area. ……..……… 11” (28cm) x 18” (46cm) JH-10 Dry ……………………..… 817 lbs (371 kgs) Vise Size ………………………. 5” (13cm) x 11” (28cm) JH-10 Wet ……………………….. 850 lbs (386 kgs)
  • Page 5 6/02 SAFETY INFORMATION LABEL LABEL LABEL LABEL 84604 84395 76462 84605 LABEL 84605 – SAFETY INSTRUCTIONS When you see this symbol on your saw, be alert to the potential for personal injury. Follow recommended precautions and safe operating practices. Carefully read all safety messages in these instructions and on your saw safety signs.
  • Page 6 6/02 LABEL 76462 – SAFETY INSTRUCTIONS LABEL 84395 – DANGER LABEL LABEL 84604 – WARNING Follow recommended precautions and safe operating practices. Carefully read all safety messages in these instructions and on your saw safety signs. Keep safety labels in good condition. Replace missing or damaged safety labels.
  • Page 7 6/02 ELECTRICAL CONTROL DIAGRAMS...
  • Page 8 6/02 SINGLE PHASE ELECTRICAL DIAGRAM...
  • Page 9 6/02 THREE PHASE ELECTRICAL DIAGRAM...
  • Page 10 6/02 MACHINE FEATURES Head Feed Blade Control Tension Handle Off-On Guide Arm Switch & Starter Balance Vise Spring Handwheel Stock Stop Gauge SECTION 1...
  • Page 11 6/02 OPERATION OFF/ON SWITCH All J-saw machines are equipped with a manual starter with low voltage, dropout protection and a limit switch. When the machine frame reaches the end of its down travel it contacts the limit switch, turning off the machine. HYDRAULIC CONTROL The hydraulic control cylinder mounted on the rear of the machine is operated by a control valve mounted on the front of the machine head.
  • Page 12 6/02 OPERATING INSTRUCTIONS 1. Raise frame and close feed cylinder valve to hold frame in elevated position. 2. Loosen the vise nut and open the vise. Place work in vise and slide the vise swivel jaw against the work piece. Engage the vise nut and tighten the vise screw to clamp the work securely.

  • Page 13: Blade Selection

    6/02 require less feed than hard materials. Thin cross-sections require less feed than solid cross- sections. Generally, reduced feed pressure will result in a straighter more accurate cut. BLADE SELECTION Saw blades should be selected by choosing the blade that will give the best results at the lowest cost.
  • Page 14 6/02 BLADE INSTALLATION 1. Raise frame a few inches above bed and close feed cylinder valve to hold frame up. 2. Remove necessary guards and blade cleaning brushes. 3. Turn blade tension screw counterclockwise and pull idle wheel toward center of machine. 4.

  • Page 15: Blade Guide Adjustment

    6/02 BLADE GUIDE ADJUSTMENT NOTE: The following instructions are for one guide arm; procedure is same for both. Left hand guide arm is shown in Figure 6. 1. Loosen nut (A, Fig. 6) and turn eccentric axle (B) until there is no light gap between rollers and blade…do not pinch the blade.

  • Page 16: Maintenance

    6/02 MAINTENANCE LUBRICATION Lube Instructions Point Description Interval Lubricant Drive wheel ring gear 6 months Clean thoroughly before lubricating. Gear box Maintain level Maintain level at 2 to 3 ounces. Drain and refill yearly. Capacity 3 ounces. Pivot bar (2 fittings) Monthly Use grease gun.
  • Page 17 6/02 SAWING PROBLEMS & SOLUTIONS...
  • Page 18 Section 3 6/02 ASSEMBLIES AND PARTS LIST...

  • Page 19: Machine Assembly, Front View

    10268-05A Right Leg Pan 10093-00 Frame Handle 10229-00 Brush holder Guard 72295 Dake/Johnson Name Plate 71541 Submersible Coolant Pump – Electric 110 volt PARTS NOT ILLUSTRATED PART NO. DESCRIPTION 10079-05 Motor, 230/460 volt, 60 Hz, 3 phase – 1 H.P.

  • Page 20: Machine Assembly, Top View

    Driven Pulley – 3/4" Bore (Key – Part No. 71061) 10510-01 Drive Wheel Assembly (J-10) 10010-01 Drive Wheel Only (J-10) 10052-00 Ring Gear (Used on J-10 and JH-10) 10510-03 Drive Wheel Assembly (JH-10) 10010-03 Drive Wheel Only (JH-10) 10062-00 Wheel Axle (J-10 & JH-10) 10134-01 Bearing Cup (J-10 &...

  • Page 21: Gearbox Assembly

    6/02 GEARBOX ASSEMBLY ITEM PART NO. DESCRIPTION 10544-00 Gear Case Assembly Complete 5047-00 Bearing Cap 5138-00 Cap Gasket 5073-00 Bearing 5044-00 Gear Case 3922 Dowel Pin 5072-00 Bearing 10049-00 Worm Gear Shaft 8 & 15 10050-51 Worm – Steel Worm & Gear Bronze Assembly 13080-01 Cover Gasket 5045-00...

  • Page 22: Hydraulic Assembly

    6/02 HYDRAULIC ASSEMBLY...
  • Page 23 6/02 ITEM PART NO. DESCRIPTION 10530-10 Hydraulic Assembly (Includes Control Valve Assembly) 10530-09 Cylinder Assembly (Only) 10031-00 Cylinder Base 10203-03 Fiber Seal 10205-02 Tie Rod 5129-00 Spring 5116-00 Spring – R Style included in repair kit. 17817 3/8 inch Ball 10204-02 Piston Rod 10033-00...

  • Page 24: Guide Arm Assembly

    6/02 GUIDE ARM ASSEMBLY T-slot Dimension 5/8” New Style ITEM PART NO. DESCRIPTION 10519-10 Guide Arm Assembly Complete LH & RH 1” (items 1-8, 14) 10019-10 Guide Arm LH & RH 10020-10 Guide Holder 10084-01 Guide Arm Tightening Handle 10025-01 Side Guide Bearing 5026-00 Upper Guide Bearing...

  • Page 25: Vise Unit

    6/02 VISE UNIT ITEM PART NO. DESCRIPTION 10007-00 Hold Down Block 10099-00 Vise Lift 5200-00 Handle 10008-00 Movable Vise Jaw (Bolt – Part No. 43348) 10009-00 Stationary Vise Jaw (Bolt – Part No. 43348) 10116-00 Lift Pin 10201-00 Vise Nut Plate (Self Tapping Screw (10-24) – Part No. 43882) 10016-00 Vise Nut 10015-10...
  • Page 26 Horizonal Bandsaws, Vertical Bandsaws and Cold Saws A complete line of Arbor, H-Frame and custom engineered competitively priced. Hydraulic Presses for production, maintenance and research work. DAKE Division of JSJ 724 Robbins Road Grand Haven, MI 49417 Phone: 1-800-937-3253 616-842-7110...

This manual is also suitable for:

J-10Jh10w3Jh10w1

Table of Contents