Table of Contents
Advertisement
Quick Links
Video-inserter
CI-RL1-RLK
Compatible with
Dacia, Fiat,
Smart
and
Renault
vehicles
with RLink or MediaNav system
and
Opel
vehicles with Navi 50 or Navi 80
Video-inserter with 2 video inputs and rear-view camera input
Product features
Video-inserter for factory-infotainment systems
2 video-inputs for after-market devices (e.g. DVD-Player, DVB-T tuner)
Rear-view camera video-input
Automatic switching to rear-view camera input on engagement of the reverse gear
Video-in-motion (ONLY for connected video-sources)
Video-inputs NTSC compatible
Version 07.02.2023
HW CAM(V31)/(V22)
CI-RL1-RLK
Advertisement
Table of Contents
Related Manuals for NavLinkz CI-RL1-RLK
Summary of Contents for NavLinkz CI-RL1-RLK
- Page 1 Video-inserter CI-RL1-RLK Compatible with Dacia, Fiat, Smart Renault vehicles with RLink or MediaNav system Opel vehicles with Navi 50 or Navi 80 Video-inserter with 2 video inputs and rear-view camera input Product features Video-inserter for factory-infotainment systems 2 video-inputs for after-market devices (e.g. DVD-Player, DVB-T tuner) ...
-
Page 2: Table Of Contents
2.4.2.1. Warning notes, concerning the installation of ribbon cables 2.5. Connection – video sources 2.5.1.1. After-market rear-view camera 2.5.2. Audio-insertion 2.7. Connecting - external keypad 2.8. Picture settings 3. Interface operation Specifications Frequently asked questions Version 07.02.2023 HW CAM(V31)/(V22) CI-RL1-RLK... -
Page 3: Prior To Installation
1. Prior to installation Read the manual prior to installation. Technical knowledge is necessary for installation. The place of installation must be free of moisture and away from heat sources. 1.1. Delivery contents Version 07.02.2023 HW CAM(V31)/(V22) CI-RL1-RLK... -
Page 4: Checking The Interface Compatibility Of Vehicle And Accessories
Factory rear-view camera Automatic switch to factory rear-view camera only while reverse gear is engaged. To delay the switch reset, additional electronics is required. Video input signal NTSC video sources compatible only. Version 07.02.2023 HW CAM(V31)/(V22) CI-RL1-RLK... -
Page 5: Video-Interface
Rear-view cam type after-market factory or none Monitor specific set to OFF adjustments See following chapters for detailed information. After each Dip-switch-change a power-reset has to be performed! See the following chapters for detailed information. Version 07.02.2023 HW CAM(V31)/(V22) CI-RL1-RLK... -
Page 6: Enabling The Interface's Video Inputs (Dip 2-3)
2.1.2. Place of installation - daughter PCB The interface’s daughter PCB is prepared to be installed between the head unit’s housing and the monitor panel. For this purpose the housing of head-unit have to be opened. Version 07.02.2023 HW CAM(V31)/(V22) CI-RL1-RLK... -
Page 7: Connection Scheme
2.2. Connection Scheme Version 07.02.2023 HW CAM(V31)/(V22) CI-RL1-RLK... -
Page 8: Connection - 6Pin Interface Cable
Note: The connection of the green wire (Reverse signal) will be described in chapter “After- market rear-view camera”. The white wire, can be used by +12V impulse to switch the enabled video sources , same as the keypad (see chapter “video interface-operation”). Version 07.02.2023 HW CAM(V31)/(V22) CI-RL1-RLK... -
Page 9: Installation Of Ribbon Cables Into Monitor Panel
20pin connector of the interface. Take care for installing the cable in the right direction as both connectors seem to be identical. (Take notice of the wire`s caption “MONITOR SIDE” and “BOX SIDE” Version 07.02.2023 HW CAM(V31)/(V22) CI-RL1-RLK... -
Page 10: Warning Notes, Concerning The Installation Of Ribbon Cables
180° position to the connector. Each deviation from a perfect contact position will curse faulty contact and even danger of short circuit 2) The ribbon cable’s contacting side always has to correspond to the contacting side of the connector, concerning the mounting position. Version 07.02.2023 HW CAM(V31)/(V22) CI-RL1-RLK... - Page 11 PCB, otherwise the length of the screws may cause destruction inside the monitor! The picture on the right side shows the position for leading out the out the ribbon cables Note: Please observe above warning notes for ribbon cable installation! Version 07.02.2023 HW CAM(V31)/(V22) CI-RL1-RLK...
-
Page 12: Connection - Video Sources
Note: The picture settings for CAM input have to be adjusted in AV2. Connect the RCA of the video source 1 and video source 2 to the female RCA „Video IN1“ and „Video IN2“ of the video cable. Version 07.02.2023 HW CAM(V31)/(V22) CI-RL1-RLK... -
Page 13: After-Market Rear-View Camera
Connect the output connector (87) of the relay to the rear-view camera’s power- cable, like you did it to the green switching input cable before. Connect stabile and permanent +12V to the relay’s input connector (30). Version 07.02.2023 HW CAM(V31)/(V22) CI-RL1-RLK... -
Page 14: Audio-Insertion
Connect the keypad’s female 4pin connector to the male 4pin connector of the video- interface. Note: Even if the switching through several video sources by the keypad mightn’t be required, the keypad’s invisible connection and availability is strongly recommended. Version 07.02.2023 HW CAM(V31)/(V22) CI-RL1-RLK... -
Page 15: Picture Settings
Note: The OSD menu is only shown when a working video source is connected to the selected video-input of the interface. The following settings are available: Brightness Contrast Saturation Position H (horizontal) Position V (vertical) Version 07.02.2023 HW CAM(V31)/(V22) CI-RL1-RLK... -
Page 16: Interface Operation
190mA @12V Video input 0.7V - 1V Video input formats NTSC RGB-video amplitude 0.7V with 75 Ohm impedance Temperature range -40°C to +85°C Dimensions video-box 113 x 25 x 97mm (W x H x D) Version 07.02.2023 HW CAM(V31)/(V22) CI-RL1-RLK... - Page 17 Camera input picture fluorescent light which shines Test camera under natural light outside the garage. flickers. directly into the camera. Camera input picture is Protection sticker not Remove protection sticker from lens. bluish. removed from camera lens. Version 07.02.2023 HW CAM(V31)/(V22) CI-RL1-RLK...
- Page 18 Cut the grey wire of 6pin to 8pin and isolate both Interface switches compatibility to vehicle is ends. If problem still occurs, additionally cut the white video-sources by itself. limited. wire of 6pin to 8pin cable and isolate both ends. 10R-03 5384 Made in China Version 07.02.2023 HW CAM(V31)/(V22) CI-RL1-RLK...
Need help?
Do you have a question about the CI-RL1-RLK and is the answer not in the manual?
Questions and answers