JVC HR-S9600EU Instructions Manual page 58

58
EN
N U M BER
Storing Cha nnels M a nua lly
Store channels that were not stored during Auto Set Up (
6), Preset Download (
ACCESS MAIN MEN U
Press M EN U .
1
ACCESS CO N FIRMATIO N
SCREEN
Press %fi to move the highlight bar (pointer) to
2
" MANUAL CH SET" , then press O K or
mation screen appears.
SELECT PO SITIO N
Press % fi
3
@ #
open position in which
you want to store a
channel begins blinking,
then press O K . The
Manual Channel Set
screen appears.
Downloaded from: https://www.usersmanualguide.com/
1
– –:– –
2
1 2 3
4 5 6
7 8 9
3
0 4
4
3
1
M EN U
2
pg. 8) or Auto Channel Set (
#
(Ex.) To store in position 12.
until an
PR CH ID
01 25 ARD
02 CDB SKY1
03 10 ZDF
04 C65 RAI1
05 C31 BBC1
06 C32 BBC2
07 C33 3SAT
[ 5 ∞ ]
: EDIT
=
= [X] : DELETE
[MENU] : EXIT
The blueback screen and the
programme currently being
broadcast by the selected channel
appear alternately for 8 seconds
each.
SU BSID IARY SETTIN GS (cont.)
4
O K
5
pg.
pg. 56). 6
7
. The Confir-
ATTEN TIO N
Guide Program numbers are not set when channels are
PR CH ID
08 C26 E-SP
stored manually. If an attempt is made at timer program-
09 55 WEST
ming with S
10 C24 SAT1
11 C23 OSF screen appears; set the Guide Program numbers on this
12 – – – –
screen.
13 – – – –
Number Set" on pg. 29.
14 – – – –
Or perform " Guide Program Number Set" (
SELECT BAN D
Press % fi to change the
band between CH (regular)
and CC (cable), then
press .
#
The blueback screen and the
programme currently being
broadcast by the selected channel
appear alternately for 8 seconds
each.
IN PUT CHAN N EL
Press the NUMBER keys to input the channel number you
want to store.
● Input "0" before any single number entries.
● To input the registered station name (ID –
press until "----" (ID setting) begins blinking, then
#
press % fi .
● For fine tuning adjustment, press
blinking, then press % fi . While tuning, " +" or " –"
appears.
● When storing a channel that sends scrambled
broadcasts, press until "OFF" (Decoder setting)
#
blinks, then press %fi to set "DECODER" to "ON"
("OFF" is the default setting).
● When "AV2 SELECT" is set to "AV2", the "DECODER"
setting cannot be changed (
EN TER N EW CHAN N EL
IN FO RMATIO N
Press OK and the Confirmation screen appears.
● Repeat steps 3 through 6 as necessary.
CLO SE CO N FIRMATIO N
SCREEN
Press M EN U .
● To change positions, see "Change Station Channel
Position" ( pg. 59).
● If you wish to set station names other than the ones
registered in your recorder,
page 60.
V in this state, the " GUIDE PROG SET"
HOW IEW
" ATTENTION – Regarding Guide Program
PR CH ID FINE DECODER
12 CH01 – – – – +/– OFF
[ 5 ∞ ] : SELECT
[ ] : CURSOR +=
: OK
[MENU] : EXIT
pg. 61),
until "+/–" begins
#
pg. 44).
"Set Stations (B)" on
pg. 66).