Bosch D9412GV4 Installation And Operation Manual page 5

7.11.2 Operation
7.11.3 Installing the D928
7.11.4 D928 Status LEDs
On-Board Points ............................................. 37
8.0
8.1 Terminals 11 to 22 Description
8.2 Point Sensor Loops
8.3 Point Parameters
8.4 Point Response Time
8.5 Wiring Information for Installations Using
the Rothenbuhler 5110/4001-42 High
Security Bell
Off-Board Points ............................................ 40
9.0
9.1 Zonex Buses
9.1.1 POPIT Modules
9.1.2 POPEX Modules
9.1.3 Missing Conditions
9.1.4 Control Panel Responses to Missing Point
Conditions
9.2 D8125 and D9127 POPIT Modules
Installing the D8125 POPEX Module
9.3
9.3.1 Mounting
9.3.2 Wiring the D8125 to the Control Panel
9.3.3 Wiring POPITs to the Data Expansion
Loop
Wiring Data Expansion Loops to POPEX
9.3.4
Modules
POPIT Sensor Loops
9.3.5
9.3.6 POPIT Module Point Assignments
9.3.7 Program Record Sheet
POPIT Labels
9.3.8
D8128D OctoPOPIT Module
9.4
9.4.1 Description
9.4.2 Listings
9.4.3 Installation
9.4.4 Setting the OctoPOPIT Switches
9.4.5 Mounting OctoPOPITs
9.4.6 Wiring OctoPOPITs
9.4.7 OctoPOPIT Sensor Loops
Testing Off-Board Points
9.5
9.6 SDI2 Octo-input Point Modules
9.7 Extra Point Events
10.0 Off-Board Relays ................................................. 56
10.1 D8129 OctoRelay
10.1.1 Configuring the D8129 OctoRelay
10.1.2 Relay Outputs
10.1.3 Installation
Bosch Security Systems, Inc. | 3/12 | F01U266054-01
10.1.4 Wiring Connections
10.2 D811 Arm Status Relay Module
10.2.1 Relay Output
10.2.2 Installation
10.2.3 Wiring Connections
10.3 SDI2 Octo-output Relay Modules
11.0 Arming Devices ................................................... 62
11.1 Description
11.2 Keypad Terminals 29 to 32
11.2.1 Assigning an Address for the Keypad
11.2.2 Installation
D279A Independent Zone Control
11.3
11.4 Keyswitch
11.4.1 Description
11.4.2 Programming
11.4.3 Installation
11.4.4 Operation
12.0 SDI Devices .......................................................... 66
12.1 Description
12.2 Installation
12.2.1 Open Wide Trouble on SDI
12.3 D9131A Parallel Printer Interface Module
12.3.1 Switch Settings
12.3.2 Supervision
12.4 D9210C Access Control Interface Module
(D9412GV4 and D7412GV4)
12.4.1 Access
12.4.2 Switch Settings
12.5 SDI Addresses 88 and 92
12.5.1 Local RPS Programming
12.6 SDI Network Interface Modules
12.6.1 Address Settings
12.6.2 Supervision
13.0 SDI2 Devices ........................................................ 69
13.1 Description
13.2 Installation
13.2.1 Open Wire Trouble on SDI2
13.3 B208 Octo-input Module
13.3.1 Address Settings
13.3.2 Supervision
13.4 B308 Octo-output Module
13.4.1 Address Settings
13.4.2 Supervision
13.5 B420 Ethernet Communication Module
5