Table of Contents
Advertisement
Available languages
Available languages
gb
the AC output. The typical use of this output is to charge
a lead acid battery. see 2.5.
A DC overload, disconnect the DC circuit protector. If this
happens, unplug the DC load before resetting the circuit
protector to resume operation.
OVERLOAD
The team cut the electricity supply if a consumer exceeds
the maximum, to restore supply shut off the engine and
start it again. Press the protection button 13..
STOPPING THE ENGINE
To stop the engine in an emergency, turn the starter
control (3) to the "OFF" position.
In normal operation:
Disconnect the plugged-in equipment and remove the
male plug from the generator.
Turn the starter control (3) to the "OFF" position.
Turn the fuel filler cap knob to the "OFF" position.
Ensure that both the fuel filler cap knob (6) and the engine
switch are in the "OFF" position when the generator is
stopped, transported and/or stored.
LOCATION AND TROUBLESHOOTING
Engine will not start:
Enough fuel?
Yes
Are the engine switch and fuel
valve "on"?
Yes
Enough lubricating oil?
Yes
Is there fuel in the carburetor?
Yes
NO
Spark plug works or
Replace spark plug.
not?
Shake the generator several times to make the float rise
if the generator cannot start after adding oil for the first
Is the output indicator on?
time and the oil alarm indicator stays on when pulling the
NO
starting grip.
Is the overload
indicator on?
Yes
Make sure there is no spilled fuel around the spark plug.
Does the electrical equipment
Spilled fuel may ignite.
work when plugged in directly?
If the engine still doesn't start, have the generator repaired
by a licensed repair person.
Inspection:
- Remove the spark plug rubber boot and clean any dirt
from around the spark plug.
Is the electric
circuit breaker intact?
- Remove the spark plug and place it in the spark plug
rubber boot.
- Connect the side electrode of the spark plug to the
metal parts of the engine.
- Pull the starting cord. Aspark could jump across the
gap.
Regular Service Period (1)
Item
Perform at every indicated month or operating hour
interval, whichever comes first.
Engine oil
Air cleaner
Spark plug
Spark arrester
Valve clearance
Fuel tank and filter
Fuel line
NO
Add fuel.
NO
Turn them to the "on" position.
NO
Add more qualified oil.
Start a few times to ensure that
NO
fuel enters the carburetor.
NO
Send the generator
to an authorized dealer
Send the generator to an
NO
authorized dealer.
Restart after turning off the
NO
overload indicator.
Yes
Send the generator to an
authorized dealer.
Yes
Replace the electric equipment.
Repair the electric equipment.
NO
Replace the electric circuit breaker.
Yes
Send the generator to
an authorized dealer.
Check level
Change
Check
Clean
(2)
Check-adjust
Clean
Check-adjust
Clean
Check
Every 2 years (Replace if
necessary) (3)
Yes
Yes
NO
Spark plug works or
NO
Spark plug works or
not?
not?
The equipment that connects generator doesn't start:
Is the output indicator on?
Is the output indicator on?
NO
NO
Is the overload
Is the overload
indicator on?
indicator on?
Yes
Enough fuel?
Yes
Does the electrical equipment
Does the electrical equipment
Yes
work when plugged in directly?
work when plugged in directly?
Are the engine switch and fuel
valve "on"?
Yes
Enough lubricating oil?
Yes
There is no power in the direct current electric outlet:
Is there fuel in the carburetor?
Is the electric
Is the electric
Yes
circuit breaker intact?
circuit breaker intact?
NO
Spark plug works or
not?
4_MAINTENANCE AND SERVICE INSTRUCTIONS
Is the output indicator on?
NO
Is the overload
MAINTENANCE SCHEDULE
Regular Service Period (1)
Regular Service Period (1)
indicator on?
Yes
Item
Item
Does the electrical equipment
The purpose of the maintenance and adjustment schedule
Perform at every indicated month or operating hour
work when plugged in directly?
Perform at every indicated month or operating hour
interval, whichever comes first.
interval, whichever comes first.
is to keep the generator in the best operating condition.
Engine oil
Engine oil
Inspect or service as scheduled in the table below.
Air cleaner
Air cleaner
Shut
off
the
maintenance. If the engine must be run, make sure
Spark plug
Spark plug
the area is well ventilated. The exhaust contains
Spark arrester
Spark arrester
Valve clearance
poisonous carbon monoxide gas.
Valve clearance
Fuel tank and filter
Is the electric
Fuel tank and filter
circuit breaker intact?
Use authorized parts or their equivalent. The use of
Fuel line
Fuel line
replacement parts which are not of equivalent quality
may damage the generator.
Maintenance Schedule
SAE Viscosity Grades
SAE Viscosity Grades
Single
Single
Regular Service Period (1)
viscosity
viscosity
Item
Perform at every indicated month or operating hour
interval, whichever comes first.
Multi
Engine oil
Multi
viscosity
Air cleaner
viscosity
Spark plug
Spark arrester
-20
-10
Valve clearance
-20
-10
Fuel tank and filter
0
Fuel line
0
NOTE:
1
Log hours of operation to determine proper
SAE Viscosity Grades
maintenance.
2
Service more frequently when used in dusty areas.
Single
3
These items should be serviced by an authorized
viscosity
dealer.
Multi
viscosity
-20
-10
0
(3)
(3)
-
24
-
fuel enters the carburetor.
NO
NO
Replace spark plug.
Replace spark plug.
Send the generator to an
NO
Send the generator to an
authorized dealer.
NO
authorized dealer.
NO
Add fuel.
Restart after turning off the
NO
Restart after turning off the
NO
overload indicator.
overload indicator.
NO
Turn them to the "on" position.
Send the generator to an
Send the generator to an
authorized dealer.
authorized dealer.
NO
Add more qualified oil.
Yes
Replace the electric equipment.
Yes
Replace the electric equipment.
Repair the electric equipment.
Repair the electric equipment.
Start a few times to ensure that
NO
NO
fuel enters the carburetor.
NO
Replace the electric circuit breaker.
Replace the electric circuit breaker.
NO
Replace spark plug.
Yes
Send the generator to
Yes
Send the generator to
an authorized dealer.
an authorized dealer.
Send the generator to an
NO
authorized dealer.
Restart after turning off the
NO
overload indicator.
Check level
Check level
Change
Send the generator to an
Change
authorized dealer.
Check
engine
Check
before
performing
Yes
Clean
Replace the electric equipment.
Clean
Repair the electric equipment.
Check-adjust
Check-adjust
Clean
Clean
Check-adjust
Check-adjust
NO
Clean
Replace the electric circuit breaker.
Clean
Check
Every 2 years (Replace if
Check
Every 2 years (Replace if
necessary) (3)
necessary) (3)
Yes
Send the generator to
an authorized dealer.
10W
10W
20W
20W
20
20
20W - 40.20W-50
Check level
20W - 40.20W-50
Change
15W - 40.15W-50
15W - 40.15W-50
Check
10W - 40
10W - 40
Clean
100W - 30
Check-adjust
100W - 30
Clean
0
10
20
30
40ºC
Check-adjust
0
10
20
30
40ºC
Clean
20
40
60
80
100ºF
Check
20
40
60
80
Every 2 years (Replace if
100ºF
necessary) (3)
Ambient Temperature
Ambient Temperature
10W
20W
20
20W - 40.20W-50
15W - 40.15W-50
10W - 40
100W - 30
0
10
20
30
40ºC
20
40
60
80
100ºF
Ambient Temperature
Send the generator
Send the generator
to an authorized dealer
to an authorized dealer
Yes
Yes
Send the generator
to an authorized dealer
Yes
any
(2)
(2)
(3)
(3)
(3)
(3)
30
30
40
40
(2)
(3)
(3)
30
40
Advertisement
Table of Contents
