Advertisement
Quick Links
SPLASH PROOF
CONNECTOR CAP
FITTING TOOL
57147-6000: For 52266 Housing (for AVSS0.3)
57148-6000: For 52213 Housing (for AVSS0.3)
57170-6000: For 52266 Housing (for AVS0.3)
57171-6000: For 52213 Housing (for AVS0.3)
OPERATING MANUAL
Molex Japan Co., Ltd.
INSTRUCTION MANUAL
IS-0048E
ISSUED
1989-03-07
REVISED
2007-02-23
REV.
D
Advertisement
Related Manuals for molex 57147-6000
Summary of Contents for molex 57147-6000
- Page 1 1989-03-07 REVISED 2007-02-23 REV. SPLASH PROOF CONNECTOR CAP FITTING TOOL 57147-6000: For 52266 Housing (for AVSS0.3) 57148-6000: For 52213 Housing (for AVSS0.3) 57170-6000: For 52266 Housing (for AVS0.3) 57171-6000: For 52213 Housing (for AVS0.3) OPERATING MANUAL Molex Japan Co., Ltd.
- Page 2 Molex Japan Co., Ltd. Contents of Update Instruction Manual No. IS-0048E 57147-6000, 57148-6000 Title Splash Proof Connector Cap Fitting Tool Tool Number 57170-6000, 57171-6000 Rev. Issued Description 1989/03/07 New creation release. 1989/03/16 Added the parts list. 2005/02/15 Revised to a bilingual version.
-
Page 3: Dangerous Operations
1) Unauthorized reproduction of this document in part or in whole is prohibited. 2) The contents of this document are subject to change without notice. 3) Molex Japan Co., Ltd. assumes no responsibility for losses resulting from use or misuse of this document. - Page 4 A–2 <Safety Precautions> Please read the following before operating the tool. 3. Careful handling 1) Carry out the cap fitting work with the acceptable connector after confirming the tool number. 2) Check the tool for any damage, and repair prior to use. There is fear that it causes a cap defective fitting.
- Page 5 1) Tool name: Splash Proof Connector Cap Fitting Tool 2) Tool number: (1) 57147-6000 (For AVSS0.3 and 52266 housing) (2) 57148-6000 (For AVSS0.3 and 52213 housing) (3) 57170-6000 (For AVS0.3 and 52266 housing) (4) 57171-6000 (For AVS0.3 and 52213 housing) 3) External size and weight: 230 (width) x 70 (depth) x 20 (thickness) mm, Approx.
- Page 6 Page 2 6) Tool appearance and parts name Ratchet part Handle Shut height size Housing holder Ratchet adjustment screw & fixing nut...
-
Page 7: Operation Method
Page 3 3. Operation Method 1) Grip the handle of a tool lightly to put it into the state of a preliminary that the “ratchet” is caught of 1-3 teeth. 2) Set a housing assembly to the tool so that the “cap (3)” may become parallel to the “lower jaw (4).”... -
Page 8: Daily Maintenance
The shut height size between the housing holder and the lower jaw must be in the standard value when grips the handle enough to the operation end. (Please refer the figure on the next page) [Standard value of shut height size] 57147-6000: 21.1+/-0.1mm 57170-6000: 57148-6000: 14.1+/-0.1 mm 57170-6000:... - Page 9 Rotate to right: The jaw shuts a lot. Rotate to left: The jaw shuts a little. [Standard value of shut height size] 57147-6000 & 57170-6000: 21.1+/-0.1 mm 57148-6000 & 57171-6000: 14.1+/-0.1 mm 3) Tighten the “fixing nut (2)” when a proper size is obtained.
-
Page 10: Parts List
Page 6 5. Parts List Parts Q’ty Parts Name Remarks number 57147-1005 Handle Assembly J4174 Outside Handle J4170 Inside Handle J4163 Torsion Spring J4168 Ratchet Spring J4175 Adjustment Screw J4176 J4161 Pivot Pin J4166 Ratchet Pin J4177 Handle Pin J57147-1004 Ratchet Plate J4165 Ratchet Spring Pin... - Page 11 Page 7 6. Splash Proof Connector Cap Fitting Tool Startup Checklist [Applicable Tool] 57147-6000: Splash Proof Connector Cap Fitting Tool (For AVSS0.3) 57148-6000: Splash Proof Connector Cap Fitting Tool (For AVSS0.3) 57170-6000: Splash Proof Connector Cap Fitting Tool (For AVS0.3) 57171-6000: Splash Proof Connector Cap Fitting Tool (For AVS0.3)
Need help?
Do you have a question about the 57147-6000 and is the answer not in the manual?
Questions and answers