Table of Contents
Advertisement
Quick Links
Extraction Tool
SCOPE:
The 63813-1400 Extraction Tool is used on several different connector series.
Product List
The following is a partial list of the product order numbers and their specifications this tool is designed to run. Updates to this list are
available on www.molex.com.
This tool is used on the E67 Power Train Connectors with 33467 and 33468 .64MM Terminals.
%
See Section 1, pages 2 thru 6 of this Instruction Sheet.
This tool is use on the SPOX BMI Connectors with 5263 and 45627 Terminals.
%
See Section 2, page 7 of this Instruction Sheet.
Doc No. 63813-1400
Released Date: 01-23-03
Revision: J
Revision Date: 06-21-06
Extractor Tool
Instruction Sheet
Order No. 63813-1400
Terminal Series Number
33467
33468
Terminal Series Number
08-70-1039
08-70-1040
5263
08-70-1045
08-70-1046
45627
45627-0001
Terminal Order Number
33467-0001
33467-0004
33467-0002
33467-0005
33467-0003
33467-0006
33468-0001
33468-0004
33468-0002
33468-0005
33468-0003
33468-0006
Terminal Order Number
08-70-1047
39-00-0152
39-00-0042
39-00-0159
39-00-0043
39-00-0160
39-00-0151
39-00-1167
45627-0002
45627-1001
UNCONTROLLED COPY
Page 1 of 7
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for molex 63813-1400
Summary of Contents for molex 63813-1400
- Page 1 Order No. 63813-1400 SCOPE: The 63813-1400 Extraction Tool is used on several different connector series. Product List The following is a partial list of the product order numbers and their specifications this tool is designed to run. Updates to this list are available on www.molex.com.
- Page 2 SECTION 1 E67 Power Train Connector Terminal Servicing Extractor Tool Instruction Sheet Order No. 63813-1400 For 33467 and 33468 .64mm Series Terminals MX64 1. Wire Dress Cover Removal With connector removed from module and interface facing down, gently unlatch wire dress cover latch features.
- Page 3 4. Terminal Removal Using the Molex 0.64 mm service tool (part no. 63813-1400), gently insert the tip into the terminal service hole adjacent to the terminal to be serviced. Be careful not to push the service tool into the terminal opening.
- Page 4 Give the service tool a further push to ensure that it has disengaged the terminal lock finger. Service Tool 0.64mm Terminal Terminal Finger UNCONTROLLED COPY Doc No. 63813-1400 Released Date: 01-23-03 Page 4 of 7 Revision: J Revision Date: 06-21-06...
- Page 5 If the TPA resists it may be detecting a partially installed terminal. Pull the TPA back into its pre-lock position, check to see that your terminal is fully installed and push it further into the cavity if required. Now the TPA can be seated. UNCONTROLLED COPY Doc No. 63813-1400 Released Date: 01-23-03 Page 5 of 7...
- Page 6 %$%FHE8WÁ %!##" !Á #"##%#%#%Á !&%&! &Á Et„wpÁBEÁ#" ÁTR4Á fxpƒtyq€3x€wp‰h€xÁ qpytyq€3x€wp‰h€xÁ qp„tyq€3x€wp‰h€xÁ p†ƒtyq€3x€wp‰h€xÁ # &#&!""Á 9f‰'Á# &#& " Visit our Web site at http://www.molex.com UNCONTROLLED COPY Doc No. 63813-1400 Released Date: 01-23-03 Page 6 of 7 Revision: J Revision Date: 06-21-06...
- Page 7 2. The extractor pin will depress the terminal locking tabs then pull the terminated wire out of the housing as shown. Wiggling the wire while pulling it out will help. 3. Molex does not offer repair parts for Extraction Tools due to the inexpensive nature of the tool. CONNECTOR...
Need help?
Do you have a question about the 63813-1400 and is the answer not in the manual?
Questions and answers