Related Manuals for SCHUNK GSW-B-AGE
Summary of Contents for SCHUNK GSW-B-AGE
- Page 1 Translation of the original manual Assembly and Operating Manual GSW-B-AGE Shaft interface with compensation unit...
- Page 2 Imprint Imprint Copyright: This manual is protected by copyright. The author is SCHUNK GmbH & Co. KG. All rights reserved. Technical changes: We reserve the right to make alterations for the purpose of technical improvement. Document number: 389555 Version: 05.00 | 18/01/2023 | en...
-
Page 3: Table Of Contents
5.2.2 Pressure supply with compressed air ............ 21 5.2.3 Pressure supply with machine cooling fluid .......... 21 Connection of GSW-B-AGE to toolholder ............ 23 Troubleshooting ..................... 27 Product does not move?.................. 27 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555... - Page 4 Servicing and assembling the product ............... 29 Seal kit........................ 29 Assembly drawing .................... 30 Translation of the original declaration of incorporation .......... 31 UKCA declaration of incorporation................ 32 10 Annex to declaration of Incorporation .............. 33 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555...
-
Page 5: General
Dangers for persons! Non-observance can lead to irreversible injury and even death. CAUTION Dangers for persons! Non-observance can cause minor injuries. NOTICE Material damage! Information about avoiding material damage. 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555... -
Page 6: Applicable Documents
• Observe the specified maintenance and lubrication intervals • Observe the ambient conditions and operating conditions Parts touching the workpiece and wear parts are not included in the warranty. 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555... -
Page 7: Scope Of Delivery
GSW-B-AGE 50-Z 5519205 2x M5x20, 9660013 DIN 4762 GSW-B-AGE 64-PZ 5519122 4x M5x20, 9660013 DIN 4762 GSW-B-AGE 80-PZ 5519123 4x M5x20, 9660013 DIN 4762 GSW-B-AGE 100-PZ 5519124 4x M5x20, 9660013 DIN 4762 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555... -
Page 8: Accessories Kit
• Toolholder • Adapter plate • Gripper For information regarding which accessory articles can be used with the corresponding product variants, see catalog data sheet. 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555... -
Page 9: Basic Safety Notes
• Structural changes should only be made with the written approval of SCHUNK. 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555... -
Page 10: Spare Parts
Due to its technical training, knowledge and experience, service the manufacturer personnel of the manufacturer is able to perform the delegated tasks and to recognize and avoid possible dangers. 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555... -
Page 11: Personal Protective Equipment
• Eliminate any malfunction immediately. • Observe the care and maintenance instructions. • Observe the current safety, accident prevention and environmental protection regulations regarding the product's application field. 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555... -
Page 12: Transport
The incorrect handling of disposal may impair the product's safety and cause serious injuries as well as considerable material and environmental harm. • Follow local regulations on dispatching product components for recycling or proper disposal. 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555... -
Page 13: Fundamental Dangers
Falling loads may cause serious injuries and even death. • Stand clear of suspended loads and do not step into their swiveling range. • Never move loads without supervision. • Do not leave suspended loads unattended. 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555... -
Page 14: Protection During Commissioning And Operation
Before starting up the machine or automated system, check that the EMERGENCY STOP system is working. Prevent operation of the machine if this protective equipment does not function correctly. 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555... -
Page 15: Protection Against Electric Shock
• The effectiveness of the potential equalisation must be verified by executing regular safety measurements. 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555... -
Page 16: Technical Data
Min. / max. operating pressure [bar] Compressed air 4 / 8 Machine cooling water 20 / 50 More technical data is included in the catalog data sheet. Whichever is the latest version. 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555... -
Page 17: Description
Description 4 Description 4.1 Description GSW-B_AGE Shaft interface with compensation unit (2) for use with a toolholder (1), an adapter plate (3) and a gripper (4). 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555... -
Page 18: Assembly
1. Check if the O-rings (165) are insert in the shank. If necessary, insert the O-rings (165). 2. Clamp the module with the shank or via the clamping surface (1) into the toolholder. 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555... -
Page 19: Pressure Supply
Toolholder with WELDON mount Sectional view of GSW-B-AGE clamped in the WELDON mount The shank of the GSW-B-AGE is clamped in the clamping face (1) using the set-screw (2) of the toolholder with WELDON mount. 5.2 Pressure supply NOTICE Observe the requirements for the air supply } 3 [ /... -
Page 20: Air Connections
• When using a SCHUNK gripper with AS (AS = closing the gripper with spring force): – Connection 2 or 4 on GSW-B-AGE and open the bottom connection "a" on the gripper. – Connection “A” on the gripper is to be closed with the locking screw (gripper accessory kit) and connection “B”... -
Page 21: Pressure Supply With Compressed Air
5.2.3 Pressure supply with machine cooling fluid NOTE The adapter plate (1) is not included in the scope of delivery and must be ordered according to the gripper type. 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555... - Page 22 Replace the locking screw (150) with the throttle (151). Note: Please observe the permissible pressure range! In case of deviating pressures, the function of the gripper is limited or disabled! 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555...
-
Page 23: Connection Of Gsw-B-Age To Toolholder
The fastening screws for the adapter plate are not included in the scope of delivery. Number and dimensions of fastening } 1.3 [ / screws, 7]Link Lieferumfang. Observe the maximum screw-in depth of the customer's mounting screws (2). 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555... - Page 24 DIN EN ISO 4762 according to standard Amount Max. depth of engagement from locating surface [mm] Max. tightening torque 11.0 [Nm] * included in the scope of delivery of the product 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555...
- Page 25 M3 x 40 M5 x 50 M6 x 55 M6 x 70 Mounting screw DIN EN ISO 4762 according to standard Amount Max. depth of engagement from locating surface [mm] 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555...
- Page 26 Assembly Mounting PZN-plus Max. tightening torque 0.94 11.0 18.0 18.0 [Nm] * included in the scope of delivery of the product 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555...
-
Page 27: Troubleshooting
Compressed air lines switched. Check compressed air lines. Unused air connections open. Close unused air connections. } 5.2.1 [ / The machine is equipped with a check valve. Use throttle 21]. 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555... -
Page 28: Maintenance
The retainer ring (19) can be ejected by high spring forces. Carefully disassemble the module. Disassemble the module as shown in the chapter “Assembly } 7.7 [ / drawing” 30]. 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555... -
Page 29: Servicing And Assembling The Product
• 1 × O-ring DIN 3771 (6.0×1.0) • 2 × O-ring DIN 3771 (17.0×1.5) ID.-No. of the seal kit Seal kit for ID number GSW-B-AGE 50 - 100 5522231 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555... -
Page 30: Assembly Drawing
It serves for illustration and assignment of the spare parts. Variations are possible depending on size and variant. * Wearing part, replace during maintenance. Included in the seal kit. Seal kit can only be ordered completely. 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555... -
Page 31: Translation Of The Original Declaration Of Incorporation
Person authorized to compile the technical documentation: Robert Leuthner, Address: see manufacturer's address Lauffen/Neckar, January 2023 p.p. Ralf Winkler; Head of Technology & Engineering, Mechanics Gripping Systems 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555... -
Page 32: Ukca Declaration Of Incorporation
Person authorized to compile the technical documentation: Marcel Machado, address: refer to manufacturer's address Lauffen/Neckar, January 2023 p.p. Ralf Winkler; Head of Technology & Engineering, Mechanics Gripping Systems 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555... -
Page 33: Annex To Declaration Of Incorporation
Selection of control or operating modes 1.2.6 Failure of the power supply Protection against mechanical hazards 1.3.1 Risk of loss of stability 1.3.2 Risk of break-up during operation 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555... - Page 34 Risk of being trapped in a machine 1.5.15 Risk of slipping, tripping or falling 1.5.16 Lightning Maintenance 1.6.1 Machinery maintenance 1.6.2 Access to operating positions and servicing points 1.6.3 Isolation of energy sources 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555...
- Page 35 Supplementary essential health and safety requirements for machinery intended for underground work Supplementary essential health and safety requirements for machinery presenting particular hazards due to the lifting of persons 05.00 | GSW-B-AGE | Assembly and Operating Manual | en | 389555...
- Page 36 Translation of the original manual SCHUNK GmbH & Co. KG Clamping and gripping technology Bahnhofstr. 106 - 134 D-74348 Lauffen/Neckar Tel. +49-7133-103-0 Fax +49-7133-103-2399 info@de.schunk.com schunk.com Folgen Sie uns I Follow us...