Tecnosicurezza Pulse User Instructions
  1. Manuals
  2. Brands
  3. Tecnosicurezza Manuals
  4. Locks
  5. Pulse
  6. User instructions

Tecnosicurezza Pulse User Instructions

Hide thumbs Also See for Pulse:
Table of Contents

Advertisement

Quick Links

Pulse
User Instructions

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Pulse and is the answer not in the manual?

Questions and answers

Related Manuals for Tecnosicurezza Pulse

Summary of Contents for Tecnosicurezza Pulse

  • Page 1 Pulse User Instructions...

  • Page 2: Table Of Contents

    User instructions Pulse Table of contents TABLE OF CONTENTS IMPORTANT NOTES! GENERAL INFORMATION FUNCTIONS OVERVIEW LOCK OPENING & ANAGER STANDARD USERS VERRIDE USER CHANGE CODE INSTALL/DISABLE/DELETE USERS NSTALL USERS FUNCTION ISABLE NABLE USERS FUNCTION ELETE USERS FUNCTION MANAGER CODE CHECK...

  • Page 3: Important Notes

    User instructions Pulse Important notes  Before installing this product, please read carefully the installation and operating instructions.  Locks have been designed to correctly operate in a temperature range from -5°C (23°F) to + 50°C (122°F) and in an environment with non-condensing humidity between 25% and 90%.

  • Page 4: General Information

    User instructions Pulse General information Using the keypad To start a time delay counting (if programmed), enter an opening code: LED flashes every 2s, indicating the counting. Press any key to stop the time delay counting. The opening window is indicated by a flashing and a beep alternating at 1s intervals.

  • Page 5: Functions Overview

     an ALKALINE 9V battery located in the battery compartement below the keypad;  an internal battery box provided by Tecnosicurezza (6 ALKALINE 1.5 batteries);  A power adapter (ref. N1212) with power supply interface (ref. T6006 or N620/A) both provided by Tecnosicurezza.

  • Page 6: Lock Opening

    User instructions Pulse Function access Standard mode: Hold press the key corresponding to the function for two seconds. Led remains on. Dual mode: Input a valid code that’s not the Manager code, hold press the key corresponding to the function for two seconds. Led remains on.

  • Page 7: Install/Disable/Delete Users

    User instructions Pulse Install/Disable/Delete users Install users (function #1) Hold press until the double beep. Led remains on. Enter the Manager code (and the Dallas key if needed). The keypad beeps twice. Enter the number of the user to be installed. The keypad beeps twice.

  • Page 8: Test Mode

    User instructions Pulse Test mode This function allows to verify the system is working correctly. Hold press until the double beep. Led remains on. Enter the following sequence of keys: Any working button produces 2 short beeps. A damaged button produces a long beep and the keypad switches off.

  • Page 9: Audit/Configuration Download

    Hold press again until the double beep. Place the magnetic Dallas connection cable into the reader and use the software Pulse Audit to start the download. At the end of audit download (wether direct or through a Dallas) the keypad beeps twice and the led switches off.

  • Page 10: Lock Reset

    User instructions Pulse Lock reset The reset operation will restore the system in pre-setup mode. Disconnect the power supply. Press keys to discharge the excess current. Connect the reset box on the connector 2 of the lock. Power up the reset box with a 9V battery. The keypad beeps twice.
  • Page 11 User instructions Pulse NOTES IU_Pulse_03_eng 11 of 12...

  • Page 12: Correct Disposal Of This Product

    Contacts GLOBAL HEADQUARTERS USA HEADQUARTERS SPAIN HEADQUARTERS Tecnosicurezza SpA Tecnosicurezza Inc. Tecnosicurezza Sa Via Cesare Battisti, 276 50, Thomas Lane C/Menor, 4 - Nave 10 37057 San Giovanni Lupatoto Pol.

Table of Contents