Related Manuals for Schmidt FS Series
Summary of Contents for Schmidt FS Series
- Page 1 Edition FS 01-1.E FS Series Model FS1 Instruction Manual Valid as of: 01.10.2012 • Please keep the manual for future reference! FSB1...
-
Page 2: Table Of Contents
2.1.4 Available FSW models ..................8 2.1.5 Available FSL models ..................8 2.1.6 Available FSB1 models ..................9 2.2 Specifications of the FS series ................9 2.3 Assignment of the connector ................10 2.3.1 Connecting the tension meter................. 10 2.4 Optional accessories .................... 10 2.5 Delivery includes .................... -
Page 3: Warranty And Liability
Warranty: - SCHMIDT tension meters are warranted for 12 months. Parts subject to wear, electronic components and measuring springs are not covered by the warranty. No warranty or liability will be accepted for bodily injury or property damage resulting from one or several of the following causes: - Misuse or abuse of the device. -
Page 4: Informal Safety Measures
The device is intended exclusively to be used as a tension meter. Any other use or any use exceeding this intention will be regarded as misuse. Under no circumstances shall Hans Schmidt & Co GmbH be held liable for damage resulting from misuse. -
Page 5: Available Models
Available models 2.1 General information These instruction manual refer to the FS1 model of the FS series; they are also applicable to the following models: FSP, FSH, FSW, FSL, FSB1 The individual models of the FS series are also available with the following modifications... -
Page 6: Available Fs1 Models
* Outer dimensions of front plate. ** Suitable for 95% of applications. PA = Polyamide Monofilament Should the process material differ significant from the SCHMIDT calibration material in size, rigidity or shape, we recommend special calibration using customer supplied material. -
Page 7: Available Fsp Models
* Outer dimensions of front plate. ** Suitable for 95% of applications. PA = Polyamide Monofilament Should the process material differ significant from the SCHMIDT calibration material in size, rigidity or shape, we recommend special calibration using customer supplied material. -
Page 8: Available Fsw Models
* Outer dimensions of front plate. ** Suitable for 95% of applications. PA = Polyamide Monofilament Should the process material differ significant from the SCHMIDT calibration material in size, rigidity or shape, we recommend special calibration using customer supplied material. -
Page 9: Available Fsb1 Models
International unit of tensile force: 1 cN = 1.02 g = 0.01 N 1 daN = 1.02 kg = 10.00 N Specifications of the FS series Calibration: According to SCHMIDT factory procedure Accuracy: ± 1.5 % full scale and ± 1 digit Other calibration material: ±... -
Page 10: Assignment Of The Connector
Hans Schmidt & Co GmbH. Certification to the CE specification does not extend to, and shall be invalid for any other combina- tion. Under no circumstances shall Hans Schmidt & Co GmbH be held liable for any damage resulting from the use of non-SCHMIDT sensors or cables. -
Page 11: Delivery Includes
FS sensor, SCD-1, display unit and an 5 m long connecting cable (special cable). In no event shall Hans Schmidt & Co GmbH take over any warranty coverage for, or shall be held liable for, any damage resulting from self-made cables. -
Page 12: Initial Setup
If the material path is other than vertical or if the process material deviates signifi- cantly from the SCHMIDT calibration material, you need to carry out static zero and gain adjustment as described in chapters 3.3.1 and 3.3.2. -
Page 13: Gain Adjustment
3.3.1 Zero adjustment (cont.) - Install the sensor in the desired position at the measuring location using the provided mounting holes. - Allow approx. 10 minutes for thermal stabilization of the sensor. - Thread the process material through the measuring and guide rollers, following the material path symbol on the front of the sensor. -
Page 14: Service And Maintenance
The question of finding the right frequency of calibration accuracy verification depends on several different factors: Operating time and load of the SCHMIDT tension meter Tolerance band defined by the customer Changes to the tolerance band compared to previous calibrations Therefore, the interval between verifications of calibration must be determined by the user‘s Quality Assurance Department, based on the user‘s experience. -
Page 15: Verification Of Calibration And Determination Of Repair Costs
6.1 Verification of calibration and determination of repair costs Flow chart for verifying the calibration of used tension meters, incoming and outgoing verification with Inspection Certificate 3.1 according to DIN EN 10204 Delivery Visual inspection and functional test Unit can be Vertification of the calibrated calibration... -
Page 16: Correspondence
Please indicate in your order whether you require an Inspection Certificate 3.1 according to DIN EN 10204. Service address: Hans Schmidt & Co GmbH Schichtstr. 16 84478 Waldkraiburg Germany...
Need help?
Do you have a question about the FS Series and is the answer not in the manual?
Questions and answers