Related Manuals for Schmidt FG Series
Summary of Contents for Schmidt FG Series
- Page 1 S C H M I D T c o n t r o l i n s t r u m e n t s Edition FGJN 01.E FG Series Model FGJN Operating Instructions Valid as of: 01.10.2015 • Please keep the manual for future reference!
-
Page 2: Safety Precaution
Safety Precaution *Please keep this instruction manual at your side after you read. Observe all warnings and cautions; it is extremely important and any safety serious contents are described. Expression and meaning are as follows. Warning When you use FGJN wrongly, it may cause serious problem, such as death or severe injury. Caution When you use FGJN wrongly, it might cause serious problem depend on the situation. - Page 3 Safety precaution Caution Do not use and keep the FGJN under Do not use AC plug covered with dust. the following circumstances. ・ Location which will be gotten water ・ Dusty, salinity and iron content environments It might the cause of the fire. ・...
- Page 4 INDEX 1.Product features 2.Confirmation of standard accessories 3.Part names and functions 3.1.Main unit 3.2.Display 3.2.1.Part names 3.2.2.Numeric display 3.2.3.Unit display 3.2.4.Peak hold mode display 4.Before use 4.1.Charge 4.2.Attaching measuring adapter 4.3.Attaching hanger 4.4.Tracking 4.5.Function setting 4.5.1.Sign: f01 4.5.2.Display update time: f02 4.5.3.Auto power off: f03 4.5.4.Function mode-end 4.6.Reverse the display...
-
Page 5: Product Features
1.Product Features ● Nickel –hydrogen battery enable us to use long time → 4.1. Charge ● Rated Capacity 2.000N (200.0gf, 8oz) ～ 500N (50.0kgf, 100lb) → 8 Specifications and Dimensions ● Reverse the display of the measuring value and the unit. →... - Page 6 3． Part names and functions 3.1.Main Unit ① Sensor shaft ② Display ③ PEAK key ⑤ＺＥＲＯ key ④ＵＮＩＴ key ⑨ Threaded hole ⑥ＰＯＷＥＲ key Model number ⑦ AC adapter port ⑧ Hanger attachment bolt ① Sensor shaft Force bolt (Push/Pull Force) ②...
-
Page 7: Numeric Display
3.2.Display 3.2.1.Part names Display of unit Display of measuring value. Display of peak hold mode 3.2.2.Numeric Display Display the measuring value with sign and 4 digits numbers. Compression force: plus, Tension force: minus. (It’ s available to switch plus/minus with the setting of function (f01)). Reverse display is available. -
Page 8: Attaching Measuring Adapter
4.Before use 4.1.Charge Do not charge with non- Please use AC adapter which supplied with FGJN. If you use non-attached AC adapter, electronic circuit might be broken and fire might happen. attached AC adapter. Before the FGJN arrive at your hand, nickel hydride battery might discharge electricity. Please plug attached AC adapter and charge before you use. -
Page 9: Function Setting
4.4.Tracking A load cell of strain gauge is used for FGJN as a load sensing. By using this sensor, the measuring value is slightly changed due to temperature and so on, but tracking is able to cancel this slightly change by the software. When you measure very minute forces, measuring value error might happen due to the tracking. -
Page 10: Display Update Time: F02
4.5.1.Sign: f01 It’ s available to set the sign (plus or minus) of measuring value for pushing the sensor shaft. Select the sign by use of UNIT key / Press the PEAK key to move ahead. Key operation Display Plus Minus PEAK ZERO... -
Page 11: Function Mode-End
4.5.4.Function mode-end Press ZERO key to memorize the set value and come back from function mode to standard measuring mode. In order to cancel the change of function mode, press POWER key, then turn the POWER off. 4.6.Reverse the display In the case you attach FGJN with a stand, display of the value and the units can be reversed in order to read the display easily. -
Page 12: Measuring Mode
5.2.Measuring Mode There are standard measuring mode and peak hold mode in the measuring mode. 5.2.1Standard measuring mode It’ s avairable to measure the compression and tension force. Measuring value is appeared at all times. １） Press POWER key and release ( Turn POWER on after release) ２）... - Page 13 6.Frequently –asked questions 6.1.Questions for trouble Questions Cause Presumable reason Procedure When turning on power, “OVR” is There is possibility which Due to dropment or Please send it for repair. displayed even if not applying load internal loadsell is broken. overloading and cannot be cleared by pushing ZERO key.
-
Page 14: Warranty
7.Support 7.1.Repair and Calibration We have calibration service for value. We recommend calibrating regularly for keeping up the accuracy of force gauge. Please ask our dealers for the price and lead time of the calibaration. 7.2.Warranty Nidec-Shimpo Corp. warrants, to the original purchaser of new products only, that this product shall be free from defects in workmanship and materials under normal use and proper maintenance for one year from the date of original purchase. - Page 15 8.Specifications and Dimensions Dimensions Force measuring attachments (standard accessories) Flat head φ 12 Chisel ： 70° Cone head ： 70° (43) Extension rod Ｌ＝ 92 Notched head ： 70° Hook -14- -14-...
- Page 16 Yarn Package Durometer and Shore-A Durometer Sample Cutter Balance Moisture Meter Leak Tester Softometer More than 60 years - Worldwide - Hans Schmidt & Co GmbH Mailing address: Phone: e-mail: P. O. B. 1154 int. + 49 / (0)8638 / 9410-0 info@hans-schmidt.com...
Need help?
Do you have a question about the FG Series and is the answer not in the manual?
Questions and answers