Pilz PNOZ mi2p Operation Manual
Hide thumbs
Also See for PNOZ mi2p:
- Configuration manual (359 pages) ,
- Operating instructions manual (12 pages)
Related Manuals for Pilz PNOZ mi2p
Summary of Contents for Pilz PNOZ mi2p
- Page 1 PNOZ mi2p Configurable, safe small controllers PNOZmulti Classic Operating Manual-21135-EN-04...
- Page 2 Preface This document is the original document. All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made for the user's internal purposes. Suggestions and comments for improving this documenta- tion will be gratefully received.
-
Page 3: Table Of Contents
Connecting the base unit and expansion modules ..............Commissioning ........................General wiring guidelines ......................Download modified project to the PNOZmulti system .............. Connection..........................Connection example ......................... Operation ..........................Messages ..........................Technical details ........................Order reference ........................Product ............................. Accessories ..........................Operating Manual PNOZ mi2p 21135-EN-04... -
Page 4: Introduction
Introduction Introduction Validity of documentation This documentation is valid for the product PNOZ mi2p. It is valid until new documentation is published. This operating manual explains the function and operation, describes the installation and provides guidelines on how to connect the product. - Page 5 Introduction INFORMATION This gives advice on applications and provides information on special fea- tures. Operating Manual PNOZ mi2p 21135-EN-04...
-
Page 6: Overview
Can be configured in the PNOZmulti Configurator LED indicator for: – Status of PNOZmulti Max. 8 PNOZ mi2p can be connected to the base unit Plug-in connection terminals: Either spring-loaded terminal or screw terminal available as an accessory (see Order ref- erences for accessories). -
Page 7: Safety
System requirements Please refer to the "Product Modifications PNOZmulti" document in the "Version overview" section for details of which versions of the base unit and PNOZmulti Configurator can be used for this product. Operating Manual PNOZ mi2p 21135-EN-04... -
Page 8: Safety Regulations
PNOZmulti Configurator's online help. Only use these functions once you have read and understood the documentations. Do not open the housing or make any unauthorised modifications. Please make sure you shut down the supply voltage when performing maintenance work (e.g. exchanging contactors). Operating Manual PNOZ mi2p 21135-EN-04... -
Page 9: Function Description
Calculation of the maximum reaction time between an input switching off and a linked out- put in the system switching off is described in the document "PNOZmulti System Expan- sion". Block diagram I 2 I 3 I 4 I 5 I 6 I 7 Input Operating Manual PNOZ mi2p 21135-EN-04... -
Page 10: Installation
Electrostatic discharge can damage components. Ensure against discharge before touching the product, e.g. by touching an earthed, conductive sur- face or by wearing an earthed armband. Dimensions in mm 22,5 94 (3.70") (0.88") Operating Manual PNOZ mi2p | 10 21135-EN-04... -
Page 11: Connecting The Base Unit And Expansion Modules
Please refer to the document "PNOZmulti System Expansion" for details of the number of modules that can be connected to the base unit and the module types. Operating Manual PNOZ mi2p | 11 21135-EN-04... -
Page 12: Commissioning
Proceed as described in the operating manual for the base unit. NOTICE For the commissioning and after every user program change, you must check whether the safety devices are functioning correctly. Connection Input circuit Contact Semiconductor Not safety-related 24 V DC Operating Manual PNOZ mi2p | 12 21135-EN-04... -
Page 13: Connection Example
Commissioning Connection example Poll of PLC outputs (standard function) Reset Operating Manual PNOZ mi2p | 13 21135-EN-04... -
Page 14: Operation
"I0" ... "I7" lights: Input I0 ... I7 carries a high signal "I0" ... "I7" off: Input I0 ... I7 carries a low signal Messages Legend LED on LED flashes LED off Base unit PNOZ mi2p Error FAULT Internal error on the expansion module Operating Manual PNOZ mi2p | 14 21135-EN-04... -
Page 15: Technical Details
Climatic suitability In accordance with the standard EN 60068-2-30, EN 60068-2-78 Humidity 93 % r. h. at 40 °C Condensation during operation Not permitted Max. operating height above sea level 2000 m EN 61131-2 Operating Manual PNOZ mi2p | 15 21135-EN-04... - Page 16 1 core flexible with crimp connector 0,25 - 0,75 mm², 24 - 20 AWG Spring-loaded terminals: Terminal points per connec- tion Stripping length with spring-loaded terminals 9 mm Dimensions Height 94 mm Width 22,5 mm Depth 121 mm Operating Manual PNOZ mi2p | 16 21135-EN-04...
- Page 17 Technical details Mechanical data Weight 119 g Where standards are undated, the 2020-07 latest editions shall apply. Operating Manual PNOZ mi2p | 17 21135-EN-04...
-
Page 18: Order Reference
1 set of spring-loaded terminals 783 400 Set screw terminals 1 set of screw terminals 793 400 Terminator, jumper Product type Features Order no. PNOZmulti bus terminator Terminator 779 110 KOP-XE Jumper 774 639 Operating Manual PNOZ mi2p | 18 21135-EN-04... - Page 19 We are represented internationally. Please refer to our homepage www.pilz.com for further details or contact our headquarters. Headquarters: Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany Telephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: info@pilz.com, Internet: www.pilz.com...